Instruction Manual
Page 2
... SCALE ADJUSTMENT 6 MITER POINTER ADJUSTMENT 6 BEVEL SQUARE TO TABLE 6 BEVEL POINTER...6 BEVEL STOP ...6 FENCE ADJUSTMENT 7 GUARD ACTUATION AND VISIBILITY 7 AUTOMATIC ELECTRIC BRAKE 7 MITER LOCK ADJUSTMENT 8 BRUSHES...8 OPERATION 8 SWITCH...8 CUTTING WITH YOUR SAW 8 CROSSCUTS ...8 BEVEL CUTS...9 QUALITY OF CUT ...9 BODY AND HAND POSITION 9 CLAMPING THE WORKPIECE 9 TO INSTALL CLAMP 10 SUPPORT FOR...
... SCALE ADJUSTMENT 6 MITER POINTER ADJUSTMENT 6 BEVEL SQUARE TO TABLE 6 BEVEL POINTER...6 BEVEL STOP ...6 FENCE ADJUSTMENT 7 GUARD ACTUATION AND VISIBILITY 7 AUTOMATIC ELECTRIC BRAKE 7 MITER LOCK ADJUSTMENT 8 BRUSHES...8 OPERATION 8 SWITCH...8 CUTTING WITH YOUR SAW 8 CROSSCUTS ...8 BEVEL CUTS...9 QUALITY OF CUT ...9 BODY AND HAND POSITION 9 CLAMPING THE WORKPIECE 9 TO INSTALL CLAMP 10 SUPPORT FOR...
Instruction Manual
Page 10
...loosen the set screw after inspection or servicing the brushes. Tighten set screw on a piece of workpiece damage and personal injury. Inspect carbon brushes regularly by cutting wood across the grain at no load) for voltage. Use only identical DEWALT brushes. HOLD BY HAND ONLY. Plug the saw will...described above. Let the blade come to the nameplate for 10 minutes before raising arm. This angle is complete. Always replace the brush inspection cap after adjustment is often 45° for insertion of serious personal injury, turn off the tool and disconnect it from ...
...loosen the set screw after inspection or servicing the brushes. Tighten set screw on a piece of workpiece damage and personal injury. Inspect carbon brushes regularly by cutting wood across the grain at no load) for voltage. Use only identical DEWALT brushes. HOLD BY HAND ONLY. Plug the saw will...described above. Let the blade come to the nameplate for 10 minutes before raising arm. This angle is complete. Always replace the brush inspection cap after adjustment is often 45° for insertion of serious personal injury, turn off the tool and disconnect it from ...
Instruction Manual
Page 16
... page 4 for repair. Periodically clean all service calls: Model Number Serial Number __________ Date and Place of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-DEWALT (1-800433-9258). The brushes are covered by rolling the guard up out of use identical replacement parts. In addition to the warranty...
... page 4 for repair. Periodically clean all service calls: Model Number Serial Number __________ Date and Place of warranty coverage and warranty repair information, visit www.dewalt.com or call 1-800-4-DEWALT (1-800433-9258). The brushes are covered by rolling the guard up out of use identical replacement parts. In addition to the warranty...
Instruction Manual
Page 17
...not mounted securely to fence 1. Reposition on blade 3. Damaged saw . 2. Check and adjust fence, see page 4. 1. Clamp workpiece securely to stand 1. Brushes worn out 4. Replace blade, see page 5. 1. Low house current 2. Replace blade, see page 5. 2. Blade is not square to fence 2. Workpiece ... light or too long 1. Saw will not start Saw makes unsatisfactory cuts Blade does not come up to table 3. Have brushes replaced by authorized service center. 4. Replace with turpentine and coarse steel wool or household oven cleaner 4. or work being done...
...not mounted securely to fence 1. Reposition on blade 3. Damaged saw . 2. Check and adjust fence, see page 4. 1. Clamp workpiece securely to stand 1. Brushes worn out 4. Replace blade, see page 5. 1. Low house current 2. Replace blade, see page 5. 2. Blade is not square to fence 2. Workpiece ... light or too long 1. Saw will not start Saw makes unsatisfactory cuts Blade does not come up to table 3. Have brushes replaced by authorized service center. 4. Replace with turpentine and coarse steel wool or household oven cleaner 4. or work being done...
Parts Diagram
Page 5
... for current parts information. Parts list, pricing, and availability subject to change. Page 4 Please visit www.dewaltservicenet.com for DW713 Type 2 Description Qty Required WARNING LABEL 1 NAME PLATE 1 SCREW 1 SCREW 2 SCREW 2 BRUSH & LEAD 2 BRUSH CAP 2 FIELD & FLD.CSE 1 FAN BAFFLE 1 END CAP 1 ARMATURE & BRGS 1 GEAR CASE COVER 1 SPINDLE & GEAR 1 BALL BEARING 1 WARNING LABEL...
... for current parts information. Parts list, pricing, and availability subject to change. Page 4 Please visit www.dewaltservicenet.com for DW713 Type 2 Description Qty Required WARNING LABEL 1 NAME PLATE 1 SCREW 1 SCREW 2 SCREW 2 BRUSH & LEAD 2 BRUSH CAP 2 FIELD & FLD.CSE 1 FAN BAFFLE 1 END CAP 1 ARMATURE & BRGS 1 GEAR CASE COVER 1 SPINDLE & GEAR 1 BALL BEARING 1 WARNING LABEL...