Emc PowerSwitch S5048F-ON

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 1
A00 Dell EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8 September 2020 Rev.

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 2
All rights reserved. Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you how to hardware or loss of data and tells you make better use of your product. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. © 2020 Dell Inc. Dell, EMC, and other trademarks are trademarks of their respective owners. or its subsidiaries. Other trademarks may be trademarks of Dell Inc. or its subsidiaries. CAUTION: A CAUTION indicates either potential damage to avoid the problem.

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 39
... or maintaining networks. Conventions This guide uses the following documents: ● Dell EMC Networking OS Configuration Guide ● Dell EMC Networking OS Installation Guide ● Dell EMC Networking OS Quick Start Guide ● Dell EMC Networking OS Release Notes Topics: • Objectives • Audience •... a double bar allow you to choose any or all of Layer 2 and Layer 3 networking technologies, who are in Dell EMC Networking OS. This book also includes information about your specific system. x||y Keywords and parameters separated by a bar require you...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 41
... enters CONFIGURATION mode and another user is '^]'. When the system successfully boots, enter the command line in CONFIGURATION mode, the Dell EMC Networking operating software generates an alert warning message similar to the system for the first time. Therefore, you must have a password... configured on a virtual terminal line before you can Telnet into the system. The Dell EMC Networking operating software commands are currently configuring the system: User "" on Devices Using a Command Option • Command Modes Accessing ...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 42
....1.123 ) User "admin" on line vty1 ( 123.12.1.123 ) User "Irene" on line vty3 ( 123.12.1.321 ) DellEMC#conf When another user enters CONFIGURATION mode, Dell EMC Networking OS sends a message similar to the ip hostname table HTTP configuration commands ICMP configuration commands Internet Group Management Protocol Max. at the prompt or...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 43
...key or Delete key to erase the previous character. ● Use the left and right Arrow keys to navigate left or right in the Dell EMC Networking OS command line. For example, you can take advantage of the prompt and reflects the current CLI mode. Deletes the line. Navigating the...the command structure. For more recent commands in Accessing the Command Line. Deletes all the characters from the cursor to the end of the Dell EMC Networking OS command modes, see Command Modes. Returns to the more information about command modes, see the command mode list in the history buffer...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 44
.... To filter a command output multiple times, place the save option as interface twentyfiveGigE 1/2. Filtering show command to a file for instances containing a noncapitalized ethernet. NOTE: The Dell EMC Networking OS accepts a space before or after the pipe, no space before or after the pipe to display all output at once - For example, the...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 45
...enables effective, streamlined management and administration of the platforms. To enable the VRF feature and cause all other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. You can employ this capability to activate software applications or components on a device using a command... 45 Activate the VRF application on a device by using the feature vrf command in CONFIGURATION mode. To display the state of Dell EMC Networking OS features: DellEMC# show feature Example of show feature output For a particular target where VRF is enabled, the show output...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 46
...Enter the protocol type: ● For IPv4, enter the ipv4 multicast command. For more information, see the relevant Dell EMC Networking OS Command Line Reference Guide. show feature Verify the status of the platforms. Example DellEMC# show feature Command Modes...VRF Enabled DellEMC# Command Modes To navigate and launch various CLI modes, use specific commands. Introduced on the S3100 series. Introduced on the S5048F-ON. Version Description 9.14(0.0) 9.12(1.0) 9.10(0.0) 9.10(0.0) 9.8(2.0) 9.8(1.0) 9.8(0.0P5) 9.8(0.0P2) 9.4(0.0) Updated the command to ROUTER BGP mode...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 49
...-IS). To enter IP ACCESS LIST mode: 1. Include a name for the ACL. Verify that is from 1 to 1284096. af_ipv6. NOTE: In Dell EMC Networking OS, the stack unit number and interfaces start from 0. The prompt changes to ROUTER ISIS mode. 2. The prompt changes to CONFIGURATION mode. ... standard command or the ip access-list extended command. To enter ISIS ADDRESS-FAMILY mode: 1. Verify that you are logged in Dell EMC Networking OS Open Networking platforms, the stack unit number and interfaces start from 1. Enter either standard or extended access control lists (ACLs...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 55
... OS image. The range is stored. Enter an IP address in dotted decimal format. Enter the keyword default to specify the primary Dell EMC Networking OS image. Enter the keywords stack-unit to manage the configuration files, as well as other file management commands. Enter the stack-unit ... running-config • show startup-config • show version • upgrade system • upgrade boot • verify boot system Specify the location where the Dell EMC Networking OS image used to boot the system is from 1 to the default boot sequence, use the no boot system command.

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 56
... keywords bmp-boot to retrieve the image from the image present in the DHCP offer. Introduced the support for bmp-boot on the S5048F-ON. Usage Information To display these changes in the bmp-boot option. nfsmount://filepath Enter the keyword system: to boot the system from.... Enter the keyword nfsmount: to retrieve the image from bare metal provisioning (BMP). For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Introduced on the S4048-ON. Introduced on the S3100 series. cd Change to boot one of the ...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 57
...10(0.0) 9.8(2.0) 9.8(1.0) 9.8(0.0P5) 9.8(0.0P2) 9.7(0.0) 9.0.2.0 8.3.19.0 8.3.11.1 8.3.7.0 7.6.1.0 7.5.1.0 E-Series Introduced on the S6100-ON. Introduced on the S5048F-ON. Introduced on the S6000-ON. Introduced on the S4048-ON. Introduced on the Z9000. Syntax Parameters copy source-file-url destination-file-url ...and S4048T-ON. Introduced on the S4820T. Original command. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Enter the directory name and path as follows: directory name ([[flash://]directory_path...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 58
..., Z9000, S4810, and S4820T. Added the compressed-config parameter. Introduced on the S5048F-ON. Usage Information Dell EMC Networking OS supports a maximum of the information. For example, when using Secure Copy [SCP]), enter... 9.8(0.0P5) 9.8(0.0P2) 9.7(0.0) 9.4(0.0) 9.3(0.1) 9.0.2.0 8.4.1.0 8.3.19.0 8.3.11.1 8.3.7.0 8.2.1.0 7.6.1.0 7.5.1.0 E-Series Introduced on the S4810. Introduced on the S3148. Dell EMC Networking OS prompts you can enter copy running-config scp: where running configuration to enter any required information for FTP, TFTP, and SCP. Introduced on...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 59
Example Example Example Example Example When you need to specify the target in the ensuing prompts. Dell EMC Networking OS supports copying the running-configuration to the running secure shell (SSH), so you are prompted for the user datagram protocol (UDP) port of ...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 60
...files cannot be restored. You cannot delete the root directory of the remote NFS file system. nfsmount: To delete a file or directory on the S5048F-ON. Version Description 9.12(1.0) 9.10(0.1) 9.10(0.0) 9.10(0.0) 9.8(2.0) 9.8(1.0) 9.8(0.0P5) 9.8(0.0P2) 9.7(0.0) 9.0.2.0 8.3.19.0 8.3.11.1 8.3.7.0 7.6.1.0 7.5.1.0...ON. Introduced on the S-Series. Introduced on the C-Series. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Introduced on the external USB flash, enter usbflash:// then the filename or directory...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 61
... 61 usbflash: For a directory on the S3100 series. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Introduced on the external USB flash, enter usbflash:// directory name. Command Modes... 9.10(0.0) 9.8(2.0) 9.8(1.0) 9.8(0.0P5) 9.8(0.0P2) 9.7(0.0) 9.7(0.0) 8.3.19.0 8.3.11.1 8.3.7.0 7.6.1.0 7.5.1.0 E-Series Introduced on the S6100-ON. Introduced on the S5048F-ON. Introduced on an NFS-mounted file system, enter nfsmount:// then the mount point and file path. nfsmount: For a file or directory on the...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 62
Introduced on the S5048F-ON. CAUTION: This command deletes all existing files and reformat the file system. display information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Example (NFS Mount) Related Commands flash: 2056916992 bytes total (2052784128 bytes free) DellEMC# DellEMC# dir nfsmount: Directory of nfsmount: 1 ...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 63
...EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Introduced on the Z9100-ON. Introduced on the S3148. Introduced on... 8.3.19.0 Introduced on the internal Flash, enter flash:// directory name. Syntax fsck {flash: | usbflash:} Parameters flash: For a directory on the S5048F-ON. usbflash: For a directory on the S6100-ON. Introduced on the external USB flash, enter usbflash:// directory name. Introduced on the system. including...

EMC Networking Command Line Reference Guide for the S5048F-ON System 9.14.2.8

Page 64
... system to access the device. (OPTIONAL) Enter the password. For command information about other platforms, see the relevant Dell EMC Networking OS Command Line Reference Guide. Introduced on the S-Series. Introduced on the S4048-ON. Introduced on the S3100 series. ...Introduced on the S5048F-ON. Example Related Commands Version 9.12(1.0) 9.10(0.1) 9.10(0.0) 9.10(0.0) 9.8(2.0) 9.8(1.0) 9.8(0.0P5) 9.8(0.0P2) 9.7(0.0) Description Introduced on the S3100 series...

Emc PowerSwitch S5048F-ON - Dell