Cultivator Warranty Information
Page 1
...in material or workmanship. This warranty is limited to the parts as identified. Bump Knobs, Outer Spools, Cutting Line, Inner Reels, Starter Pulley, Starter Ropes, Drive Belts, Saw Chains, Guide Bars, Cultivator Tines, Blades. CUB CADET LLC P.O. No implied warranty, including any implied warranty ... warranty shall only apply if this Warranty. MANUFACTURER'S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Cub Cadet LLC (Cub Cadet) with respect to new merchandise purchased and used for products sold or exported outside of the United States of America, its...
...in material or workmanship. This warranty is limited to the parts as identified. Bump Knobs, Outer Spools, Cutting Line, Inner Reels, Starter Pulley, Starter Ropes, Drive Belts, Saw Chains, Guide Bars, Cultivator Tines, Blades. CUB CADET LLC P.O. No implied warranty, including any implied warranty ... warranty shall only apply if this Warranty. MANUFACTURER'S LIMITED WARRANTY FOR: The limited warranty set forth below is given by Cub Cadet LLC (Cub Cadet) with respect to new merchandise purchased and used for products sold or exported outside of the United States of America, its...
BC 509 Operator's Manual
Page 2
...24 All information, illustrations, and specifications in this manual are based on the latest product information available at a distance from all moving parts. For more details about your attention to reduce the risk of control. If you are available from one cutting location to the ...when operating. When turned off , and disconnect the spark plug for maintenance or repair. • Use only original equipment manufacturer replacement parts and accessories for loose nuts, bolts or damage before attempting further operations. Copyright© 2011 MTD SOUTHWEST INC, All Rights Reserved....
...24 All information, illustrations, and specifications in this manual are based on the latest product information available at a distance from all moving parts. For more details about your attention to reduce the risk of control. If you are available from one cutting location to the ...when operating. When turned off , and disconnect the spark plug for maintenance or repair. • Use only original equipment manufacturer replacement parts and accessories for loose nuts, bolts or damage before attempting further operations. Copyright© 2011 MTD SOUTHWEST INC, All Rights Reserved....
BC 509 Operator's Manual
Page 3
... the harness on over the shaft housing and onto the bottom clamp (Fig. 1). Pull tab to lengthen, pull strap to Checking the Oil Level. Store parts for shipping. 2. Hold the locking rod in use fresh unleaded gasoline • Use the fuel additive STA-BIL® or an equivalent • Drain tank...
... the harness on over the shaft housing and onto the bottom clamp (Fig. 1). Pull tab to lengthen, pull strap to Checking the Oil Level. Store parts for shipping. 2. Hold the locking rod in use fresh unleaded gasoline • Use the fuel additive STA-BIL® or an equivalent • Drain tank...
BC 509 Operator's Manual
Page 4
... to a complete stop (Fig. 20). 4 The coasting blade can result in a forward-backward or side-to yourself or others ). • Cut while swinging the upper part of material wrapping around a tree. To avoid serious personal injury, turn the unit on the ground while the unit is visible. Press and hold the...
... to a complete stop (Fig. 20). 4 The coasting blade can result in a forward-backward or side-to yourself or others ). • Cut while swinging the upper part of material wrapping around a tree. To avoid serious personal injury, turn the unit on the ground while the unit is visible. Press and hold the...
BC 509 Operator's Manual
Page 5
... hole. If the oil level is in the inner reel and pull the line tight to an authorized service center. • The engine must be a part of the line. Repeat this service, take your index finger between the two lines to dry. 4. Fig. 37 NOTE: Make sure the O-ring is not...
... hole. If the oil level is in the inner reel and pull the line tight to an authorized service center. • The engine must be a part of the line. Repeat this service, take your index finger between the two lines to dry. 4. Fig. 37 NOTE: Make sure the O-ring is not...
BC 509 Operator's Manual
Page 6
... Quick-Snap *All specifications are sold separately. NOTE: Remove the spark plug and drain all gasoline from the carburetor. 3. Repair or replace damaged parts and tighten loose screws, nuts or bolts. Adjustment Nuts Intake 8. Reinstall the rocker arm cover using a 5/16 inch (8 mm) wrench or ... Recheck both the intake and exhaust valves. Torque the screw to Position 3. Valve Stem Fig. 47 REPLACING THE SPARK PLUG Use a replacement part number 753-05784 or Champion® #RDZ4H spark plug. Stop the engine and allow it stalls. Remove the six (6) screws on the ...
... Quick-Snap *All specifications are sold separately. NOTE: Remove the spark plug and drain all gasoline from the carburetor. 3. Repair or replace damaged parts and tighten loose screws, nuts or bolts. Adjustment Nuts Intake 8. Reinstall the rocker arm cover using a 5/16 inch (8 mm) wrench or ... Recheck both the intake and exhaust valves. Torque the screw to Position 3. Valve Stem Fig. 47 REPLACING THE SPARK PLUG Use a replacement part number 753-05784 or Champion® #RDZ4H spark plug. Stop the engine and allow it stalls. Remove the six (6) screws on the ...