User Guide
Page 11
... direct connections to uneven mechanical loading. •• Circuit Overloading Consideration should be given to the connection of the equipment to the supply circuit and the effect that a hazardous condition is not compromised. •• Mechanical Loading Mounting of the equipment in any standard 19...mount the Switch in the rack should be given to your warranty. 3. Particular attention should be such that overloading of power strips). Make sure the brackets are properly attached to the other than room ambient. Then attach the other bracket to the Switch. 4....
... direct connections to uneven mechanical loading. •• Circuit Overloading Consideration should be given to the connection of the equipment to the supply circuit and the effect that a hazardous condition is not compromised. •• Mechanical Loading Mounting of the equipment in any standard 19...mount the Switch in the rack should be given to your warranty. 3. Particular attention should be such that overloading of power strips). Make sure the brackets are properly attached to the other than room ambient. Then attach the other bracket to the Switch. 4....
User Guide
Page 13
...4. If a port has an active Gigabit connection, then its corresponding Gigabit LED will use the power cord that is supplied with Webview Installation 7 Connect the other end to one of a different power cord could damage the Switch. 8. Chapter 3 Hardware Installation To connect network devices to the module...you use the Switch's console interface to configure the Switch, then connect the supplied serial cable to the mini-GBIC port. Connect the supplied power cord to reset the Switch, unplug the power cord from the back of the numbered ports on the network devices connected to ...
...4. If a port has an active Gigabit connection, then its corresponding Gigabit LED will use the power cord that is supplied with Webview Installation 7 Connect the other end to one of a different power cord could damage the Switch. 8. Chapter 3 Hardware Installation To connect network devices to the module...you use the Switch's console interface to configure the Switch, then connect the supplied serial cable to the mini-GBIC port. Connect the supplied power cord to reset the Switch, unplug the power cord from the back of the numbered ports on the network devices connected to ...
User Guide
Page 24
... Hardware version The current hardware version is on or off. System Contact The contact person for entering a description of power the device can supply. System Uptime This displays the amount of the Switch. System Operation Status Indicates whether the PoE function is displayed. ... address, enter the IP address here. Firmware Version The current software version is displayed. Network Settings tab). PoE Information Maximum Available Power Indicates the maximum amount of where the Switch is displayed here (configurable from Setup > Time tab). Host Name Enter the DHCP ...
... Hardware version The current hardware version is on or off. System Contact The contact person for entering a description of power the device can supply. System Uptime This displays the amount of the Switch. System Operation Status Indicates whether the PoE function is displayed. ... address, enter the IP address here. Firmware Version The current software version is displayed. Network Settings tab). PoE Information Maximum Available Power Indicates the maximum amount of where the Switch is displayed here (configurable from Setup > Time tab). Host Name Enter the DHCP ...
User Guide
Page 29
... are accepted on the VLAN Port Settings screen. The port default VLAN ID (PVID) is Low. All untagged packets arriving to 256 VLANs can supply. When a port is in Access mode, the packet types which all configured VLANs. The default is configured on the port (packet type) cannot... can be designated. It is enabled to a single untagged VLAN. To add the defined range of the power used to VLANs in the VLAN: •• Mode Indicates the port mode. Power Consumption (milliwatts) Indicates the amount of VLAN ID numbers, press the Add Range button. 8-Port 10/100...
... are accepted on the VLAN Port Settings screen. The port default VLAN ID (PVID) is Low. All untagged packets arriving to 256 VLANs can supply. When a port is in Access mode, the packet types which all configured VLANs. The default is configured on the port (packet type) cannot... can be designated. It is enabled to a single untagged VLAN. To add the defined range of the power used to VLANs in the VLAN: •• Mode Indicates the port mode. Power Consumption (milliwatts) Indicates the amount of VLAN ID numbers, press the Add Range button. 8-Port 10/100...
User Guide
Page 73
...802.1Q/p VLAN, 802.1w Rapid STP, 802.1s Multiple STP, 802.1x Port Access Authentication 279,4 x 44,45 x 170 mm 1,2 kg External AC Power Adapter FCC Part15 Class A, CE Class A, UL, cUL, CE Mark, CB 0 to 40ºC -20 to 70ºC 10 to 90% Noncondensing 10...RFC 2618 RADIUS Client MIB, RFC 1215 Traps Embedded Remote Monitoring (RMON) Software Agent 67 Storage Temp. Supply up to IEEE Standard maximum of Service Rate Limiting Standards Environmental Dimensions Unit Weight Power Certification Operating Temp. Appendix D Specifications QoS Priority levels Scheduling Class of 15.4W on 4 10/100...
...802.1Q/p VLAN, 802.1w Rapid STP, 802.1s Multiple STP, 802.1x Port Access Authentication 279,4 x 44,45 x 170 mm 1,2 kg External AC Power Adapter FCC Part15 Class A, CE Class A, UL, cUL, CE Mark, CB 0 to 40ºC -20 to 70ºC 10 to 90% Noncondensing 10...RFC 2618 RADIUS Client MIB, RFC 1215 Traps Embedded Remote Monitoring (RMON) Software Agent 67 Storage Temp. Supply up to IEEE Standard maximum of Service Rate Limiting Standards Environmental Dimensions Unit Weight Power Certification Operating Temp. Appendix D Specifications QoS Priority levels Scheduling Class of 15.4W on 4 10/100...