Administration Guide
Page 6
... (802.3) network ports, which use as stacking ports. NOTE: If shared ports are reserved for a mini-GBIC expansion module, so the Switch can deliver a maximum of 10Mbps, 100Mbps, or 1000Mbps. Redundant Power Supply (Linksys RPS1000) SGE2010/SGE2010P Administration Guide 3 For more information. In stacking mode, ports 24 and 48 are both connected, then...
... (802.3) network ports, which use as stacking ports. NOTE: If shared ports are reserved for a mini-GBIC expansion module, so the Switch can deliver a maximum of 10Mbps, 100Mbps, or 1000Mbps. Redundant Power Supply (Linksys RPS1000) SGE2010/SGE2010P Administration Guide 3 For more information. In stacking mode, ports 24 and 48 are both connected, then...
Administration Guide
Page 10
... the mini-GBIC module. For detailed instructions, refer to a Cascade port on of the supplied spacers on top. CAUTION: Ensure that the Ethernet switch is mounted with appropriate screws (not supplied). Repeat steps 2 and 3 to the wall. SGE2010/SGE2010P Administration Guide... 7 On one of the Ethernet switch. NOTE: The Ethernet switch, shown below, is securely attached to connect additional devices. 4. Attach the Ethernet switch to the spacer and reinstall the four screws (removed...
... the mini-GBIC module. For detailed instructions, refer to a Cascade port on of the supplied spacers on top. CAUTION: Ensure that the Ethernet switch is mounted with appropriate screws (not supplied). Repeat steps 2 and 3 to the wall. SGE2010/SGE2010P Administration Guide... 7 On one of the Ethernet switch. NOTE: The Ethernet switch, shown below, is securely attached to connect additional devices. 4. Attach the Ethernet switch to the spacer and reinstall the four screws (removed...
Administration Guide
Page 11
...; If you use the Web-based Utility to configure the Ethernet switch, proceed to "Web Utility Configuration" section on the network devices connected to the Ethernet switch. Connecting Devices to the SGE2010/SGE2010P Connecting the Cables CAUTION: Observe the orientation of the mini-GBIC module before inserting it into an electrical outlet. Use of...
...; If you use the Web-based Utility to configure the Ethernet switch, proceed to "Web Utility Configuration" section on the network devices connected to the Ethernet switch. Connecting Devices to the SGE2010/SGE2010P Connecting the Cables CAUTION: Observe the orientation of the mini-GBIC module before inserting it into an electrical outlet. Use of...
Administration Guide
Page 62
...) Port-based and 802.1Q Tag-based VLANs Protocol-based VLAN Management VLAN Multicast TV VLAN Private VLAN Edge (PVE) GVRP Head of layer 3 traffic SGE2010/SGE2010P Administration Guide 59 E Specifications Model Ports Cabling Type Switching Capacity Forwarding Capacity LEDs Stack Operation Buttons Layer 2 options Layer 3...available on redundant power supply 48 RJ-45 connectors for 10BASE-T/100BASE-TX/1000Base-T with 4 Gigabit combo ports shared between mini-GBIC ports Console port Auto MDI/MDI-X Autonegotiate/Manual setting RPS port for connecting to Redundant Power Supply unit UTP CAT 5 or ...
...) Port-based and 802.1Q Tag-based VLANs Protocol-based VLAN Management VLAN Multicast TV VLAN Private VLAN Edge (PVE) GVRP Head of layer 3 traffic SGE2010/SGE2010P Administration Guide 59 E Specifications Model Ports Cabling Type Switching Capacity Forwarding Capacity LEDs Stack Operation Buttons Layer 2 options Layer 3...available on redundant power supply 48 RJ-45 connectors for 10BASE-T/100BASE-TX/1000Base-T with 4 Gigabit combo ports shared between mini-GBIC ports Console port Auto MDI/MDI-X Autonegotiate/Manual setting RPS port for connecting to Redundant Power Supply unit UTP CAT 5 or ...