User Guide
Page 2
... speed user data channel, rather than being multiplexed into 28 DS1 or 21 E1 data lines in an industry standard multiplexing format. Supported Features Chapter 7 Configuring the Channelized 12-port CT3/T1 Optical Services Modules Table 7-1 Serial Interface Cost Link Type Cost DS3 336 Unframed E1 16 1-6 DS-/TS... 4 7-9 DS0/TS 6 10-16 DS0/TS 8 17-24 DS0/TS 12 25-31 TS 16 Channelized DS3 Overview In the channelized mode of operation, an OSM-12CT3/T1 link...
... speed user data channel, rather than being multiplexed into 28 DS1 or 21 E1 data lines in an industry standard multiplexing format. Supported Features Chapter 7 Configuring the Channelized 12-port CT3/T1 Optical Services Modules Table 7-1 Serial Interface Cost Link Type Cost DS3 336 Unframed E1 16 1-6 DS-/TS... 4 7-9 DS0/TS 6 10-16 DS0/TS 8 17-24 DS0/TS 12 25-31 TS 16 Channelized DS3 Overview In the channelized mode of operation, an OSM-12CT3/T1 link...
User Guide
Page 3
...) • Distributed Multilink PPP (dMLPPP) The OSM-12CT3/T1 module supports dMLPPP, which means that the MLPPP encapsulation is performed on the Optical Services Modules." Serial Encapsulation Protocols The OSMs support for each DS-3 channel • Local, line, and remote loopback. • Generation and termination of DS-3 maintenance data link (MDL) in the Cisco IOS Quality of 12 DS1/E1...
...) • Distributed Multilink PPP (dMLPPP) The OSM-12CT3/T1 module supports dMLPPP, which means that the MLPPP encapsulation is performed on the Optical Services Modules." Serial Encapsulation Protocols The OSMs support for each DS-3 channel • Local, line, and remote loopback. • Generation and termination of DS-3 maintenance data link (MDL) in the Cisco IOS Quality of 12 DS1/E1...
User Guide
Page 4
...of the timeslots giving the serial interface a bandwidth of DS-3 maintenance data link (MDL) in C-bit framing. • In T1 mode, the channelized CT3/T1 OSMs support facilities data link (FDL) in Extended Superframe (ESF) framing, as well as specified by CCITT/ITU G.704 and G.706...2SR 7-4 OL-9465-03 Each of the T1 lines contains 24 timeslots of 64 or 56 kbps each of the T1 are filled with different data link layer protocol encapsulations. Supported Features Chapter 7 Configuring the Channelized 12-port CT3/T1 Optical Services Modules DSU Mode Unchannelized DS-3 supports subrate and ...
...of the timeslots giving the serial interface a bandwidth of DS-3 maintenance data link (MDL) in C-bit framing. • In T1 mode, the channelized CT3/T1 OSMs support facilities data link (FDL) in Extended Superframe (ESF) framing, as well as specified by CCITT/ITU G.704 and G.706...2SR 7-4 OL-9465-03 Each of the T1 lines contains 24 timeslots of 64 or 56 kbps each of the T1 are filled with different data link layer protocol encapsulations. Supported Features Chapter 7 Configuring the Channelized 12-port CT3/T1 Optical Services Modules DSU Mode Unchannelized DS-3 supports subrate and ...
User Guide
Page 5
Chapter 7 Configuring the Channelized 12-port CT3/T1 Optical Services Modules Supported Features Fractional E1 lines contain only a single logical channel group that can be either a single 64-kbps timeslot or a range of Signal (LOS) • Far End Block ...Frame Relay, HDLC, and PPP encapsulations • PFC2 QoS on the Optical Services Modules." Each unframed E1 line contains no framing overhead and is a channelized E1 line. • Unframed E1-Any of Service Protocols For information on configuring QoS on the Channelized OSMs, refer to Chapter 10, "Configuring QoS on the LAN and WAN ...
Chapter 7 Configuring the Channelized 12-port CT3/T1 Optical Services Modules Supported Features Fractional E1 lines contain only a single logical channel group that can be either a single 64-kbps timeslot or a range of Signal (LOS) • Far End Block ...Frame Relay, HDLC, and PPP encapsulations • PFC2 QoS on the Optical Services Modules." Each unframed E1 line contains no framing overhead and is a channelized E1 line. • Unframed E1-Any of Service Protocols For information on configuring QoS on the Channelized OSMs, refer to Chapter 10, "Configuring QoS on the LAN and WAN ...
User Guide
Page 6
...Lines, page 7-10 Configuring the T3 Controller To configure the controller, perform this URL: http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t5/cbpmark2 .htm • Classification and priority marking based on the WAN ports. Configuring the Interfaces Chapter 7 Configuring the Channelized 12-port CT3/T1 Optical Services Modules... Configure class-based marking as described in IOS, refer to the Cisco IOS Quality of Service Solutions Configuration Guide, Release 12.1 at this task: Optical Services Modules Installation ...
...Lines, page 7-10 Configuring the T3 Controller To configure the controller, perform this URL: http://www.cisco.com/univercd/cc/td/doc/product/software/ios121/121newft/121t/121t5/cbpmark2 .htm • Classification and priority marking based on the WAN ports. Configuring the Interfaces Chapter 7 Configuring the Channelized 12-port CT3/T1 Optical Services Modules... Configure class-based marking as described in IOS, refer to the Cisco IOS Quality of Service Solutions Configuration Guide, Release 12.1 at this task: Optical Services Modules Installation ...
User Guide
Page 8
... the default encapsulation. This is 224. Configuring the Interfaces Chapter 7 Configuring the Channelized 12-port CT3/T1 Optical Services Modules Note IP addresses can not be assigned to configure. Step 7 Router(config-if)# [no ] loopback {local | network | remote {line | payload}} (Optional) Sets the loopback mode. To configure the unchannelized DS3 interfaces, perform this task: Command...
... the default encapsulation. This is 224. Configuring the Interfaces Chapter 7 Configuring the Channelized 12-port CT3/T1 Optical Services Modules Note IP addresses can not be assigned to configure. Step 7 Router(config-if)# [no ] loopback {local | network | remote {line | payload}} (Optional) Sets the loopback mode. To configure the unchannelized DS3 interfaces, perform this task: Command...
User Guide
Page 9
...OSM-12CT3/T1 module has four framers, each of E1 channelization, perform this task: OL-9465-03 Optical Services Modules Installation and Configuration Note, 12.2SR 7-9 Specifies the channelization mode. Selects the controller. Chapter 7 Configuring the Channelized 12-port CT3/T1 Optical Services Modules ...Configuring the Interfaces Configuring the Channelized DS3 Interface The DS3 Interface can be channelized down to three contiguous ports. Configuring the T3 Controller for Channelization To configure the T3 controller for T1 of the T1 and E1 lines....
...OSM-12CT3/T1 module has four framers, each of E1 channelization, perform this task: OL-9465-03 Optical Services Modules Installation and Configuration Note, 12.2SR 7-9 Specifies the channelization mode. Selects the controller. Chapter 7 Configuring the Channelized 12-port CT3/T1 Optical Services Modules ...Configuring the Interfaces Configuring the Channelized DS3 Interface The DS3 Interface can be channelized down to three contiguous ports. Configuring the T3 Controller for Channelization To configure the T3 controller for T1 of the T1 and E1 lines....
User Guide
Page 10
...t1 6 framing sf Router(config-controller)# t1 6 clock source line Router(config-controller)# t1 6 loopback remote line Router(config-controller)# t1 6 bert pattern 2^23 interval 5 unframed Router(config-controller)# exit Router(config)# interface serial t1 3/1/6:0 Router (config-if)# CNTL/Z Router# Configuring the E1 Lines To configure E1 lines, perform this task: 7-10 Optical Services Modules... Exits controller configuration mode. Configuring the Interfaces Chapter 7 Configuring the Channelized 12-port CT3/T1 Optical Services Modules Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step ...
...t1 6 framing sf Router(config-controller)# t1 6 clock source line Router(config-controller)# t1 6 loopback remote line Router(config-controller)# t1 6 bert pattern 2^23 interval 5 unframed Router(config-controller)# exit Router(config)# interface serial t1 3/1/6:0 Router (config-if)# CNTL/Z Router# Configuring the E1 Lines To configure E1 lines, perform this task: 7-10 Optical Services Modules... Exits controller configuration mode. Configuring the Interfaces Chapter 7 Configuring the Channelized 12-port CT3/T1 Optical Services Modules Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step ...
User Guide
Page 11
.../T1 Optical Services Modules Configuring the Interfaces Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 Step 11 Step 12 Command Purpose Router# configure terminal Enters configuration mode and specifies that the console terminal is t1. Router (config-controller)# [no ] e1 e1 number national Specifies the national bits reserved for the specified E1 line...
.../T1 Optical Services Modules Configuring the Interfaces Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 Step 11 Step 12 Command Purpose Router# configure terminal Enters configuration mode and specifies that the console terminal is t1. Router (config-controller)# [no ] e1 e1 number national Specifies the national bits reserved for the specified E1 line...
User Guide
Page 12
... Optical Services Modules Installation and Configuration Note, 12.2SR OL-9465-03 Note The Multilink PPP command is connected to carry two bundles of two T1 lines. One of four T1 lines. bundle-id is the bundle number created with an OSM-12CT3/T1 module. The Cisco 7600 Series router is available on serial interfaces only. Figure 7-1 MLPPP Topology Cisco 7200 Cisco 2500 T1s T1s Cisco 7200 Cisco...
... Optical Services Modules Installation and Configuration Note, 12.2SR OL-9465-03 Note The Multilink PPP command is connected to carry two bundles of two T1 lines. One of four T1 lines. bundle-id is the bundle number created with an OSM-12CT3/T1 module. The Cisco 7600 Series router is available on serial interfaces only. Figure 7-1 MLPPP Topology Cisco 7200 Cisco 2500 T1s T1s Cisco 7200 Cisco...