Hardware Installation Guide
Page 1
Cisco Interface Cards Hardware Installation Guide For the Cisco 1600 Series, Cisco 1700 Series, Cisco 1800 Series, Cisco 2600 Series, Cisco 2800 Series, Cisco 3600 Series, Cisco 3700 Series, and Cisco 3800 Series Routers, the Cisco ICS 7750, and the Cisco MWR 1941-DC Mobile Wireless Edge Router Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Text Part Number: OL-1919-18
Cisco Interface Cards Hardware Installation Guide For the Cisco 1600 Series, Cisco 1700 Series, Cisco 1800 Series, Cisco 2600 Series, Cisco 2800 Series, Cisco 3600 Series, Cisco 3700 Series, and Cisco 3800 Series Routers, the Cisco ICS 7750, and the Cisco MWR 1941-DC Mobile Wireless Edge Router Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Text Part Number: OL-1919-18
Hardware Installation Guide
Page 5
... more information. Interface Card Slot Locations and Numbering on sample Cisco access routers. or 2-slot network module. • The Cisco 3700 series, including the Cisco 3725 and Cisco 3745 routers (see Figure 11 and Figure 12) • The Cisco 3800 series, including the Cisco 3825 and Cisco 3845 routers (see Figure 13) • Cisco MWR 1941-DC routers (see Figure...
... more information. Interface Card Slot Locations and Numbering on sample Cisco access routers. or 2-slot network module. • The Cisco 3700 series, including the Cisco 3725 and Cisco 3745 routers (see Figure 11 and Figure 12) • The Cisco 3800 series, including the Cisco 3825 and Cisco 3845 routers (see Figure 13) • Cisco MWR 1941-DC routers (see Figure...
Hardware Installation Guide
Page 10
...Notes and Limitations Routers do not support HWICs. Does not support VICs in chassis slots. Supports VWICs for Cisco Interface Cards Certain platforms have restrictions on the number of total interface cards of Slots 1 2 3 Slot Type Single-wide Single-wide Single-wide 4 ...Single-wide 2 Single-wide Slot Numbering - See Table 1 for information about the interface card slots available on Cisco Access Routers Cisco Router Cisco 1600 series Cisco 1720 routers Cisco 1750 and Cisco 1751 routers Cisco 1760 routers Cisco 1800 series Cisco 2600 series Number of a certain type that can ...
...Notes and Limitations Routers do not support HWICs. Does not support VICs in chassis slots. Supports VWICs for Cisco Interface Cards Certain platforms have restrictions on the number of total interface cards of Slots 1 2 3 Slot Type Single-wide Single-wide Single-wide 4 ...Single-wide 2 Single-wide Slot Numbering - See Table 1 for information about the interface card slots available on Cisco Access Routers Cisco Router Cisco 1600 series Cisco 1720 routers Cisco 1750 and Cisco 1751 routers Cisco 1760 routers Cisco 1800 series Cisco 2600 series Number of a certain type that can ...
Hardware Installation Guide
Page 11
...network module (see the "Installing Double-Wide Interface Cards" section in Installing Cisco Interface Cards in a Cisco 3600 series router, use a 1- OL-12796-01 9 Removing the slot divider changes slot numbering as follows: • Slot 0 and slot 1 become slot 1 •...0 and slot 2 do not have interface card slots on Cisco Access Routers (continued) Cisco Router Cisco 2801 routers Cisco 2811, Cisco 2821, and Cisco 2851 routers Cisco 3600 series Cisco 3660 Cisco 3700 series Number of Slots 4 Slot Type Single-wide Slot Numbering Slot 0 through slot 3 2 Double-wide Slot 1, slot...
...network module (see the "Installing Double-Wide Interface Cards" section in Installing Cisco Interface Cards in a Cisco 3600 series router, use a 1- OL-12796-01 9 Removing the slot divider changes slot numbering as follows: • Slot 0 and slot 1 become slot 1 •...0 and slot 2 do not have interface card slots on Cisco Access Routers (continued) Cisco Router Cisco 2801 routers Cisco 2811, Cisco 2821, and Cisco 2851 routers Cisco 3600 series Cisco 3660 Cisco 3700 series Number of Slots 4 Slot Type Single-wide Slot Numbering Slot 0 through slot 3 2 Double-wide Slot 1, slot...
Hardware Installation Guide
Page 12
...-12796-01 10 Routers do not support HWICs. You must have forgotten your particular router and combination of Slots 4 2 Cisco ICS 7750 - Removing the slot divider changes slot numbering as follows: • Slot 0 and slot 1 become slot 1 • Slot 2 and slot 3 become slot ...not have an account or have an account on Cisco.com. Cisco IOS Software Releases and Cisco Interface Cards Cisco Interface Cards for Cisco Access Routers Table 1 Interface Card Slots Available on Cisco Access Routers (continued) Cisco Router Cisco 3800 series Number of cards and modules, go to the "Processor...
...-12796-01 10 Routers do not support HWICs. You must have forgotten your particular router and combination of Slots 4 2 Cisco ICS 7750 - Removing the slot divider changes slot numbering as follows: • Slot 0 and slot 1 become slot 1 • Slot 2 and slot 3 become slot ...not have an account or have an account on Cisco.com. Cisco IOS Software Releases and Cisco Interface Cards Cisco Interface Cards for Cisco Access Routers Table 1 Interface Card Slots Available on Cisco Access Routers (continued) Cisco Router Cisco 3800 series Number of cards and modules, go to the "Processor...
Hardware Installation Guide
Page 16
...-2FXO-M1 VIC-2FXO-M2 VIC-2FXO-M3 VIC2-2FXO VIC2-4FXO VIC-2CAMA VIC-2DID VIC-2E/M VIC2-2E/M Table 3 Cisco 12-in-1 Smart Serial Interface Cable Part Numbers Interface EIA/TIA-232 EIA/TIA-449 EIA-530 EIA-530A DCE/DTE Female DCE Male DTE Female DCE Male DTE Male... DTE Male DTE Cisco Cable Part Number CAB-SS-232FC CAB-SS-232MT CAB-SS-449FC CAB-SS-449MT CAB-SS-530MT CAB-SS...
...-2FXO-M1 VIC-2FXO-M2 VIC-2FXO-M3 VIC2-2FXO VIC2-4FXO VIC-2CAMA VIC-2DID VIC-2E/M VIC2-2E/M Table 3 Cisco 12-in-1 Smart Serial Interface Cable Part Numbers Interface EIA/TIA-232 EIA/TIA-449 EIA-530 EIA-530A DCE/DTE Female DCE Male DTE Female DCE Male DTE Male... DTE Male DTE Cisco Cable Part Number CAB-SS-232FC CAB-SS-232MT CAB-SS-449FC CAB-SS-449MT CAB-SS-530MT CAB-SS...
Hardware Installation Guide
Page 17
... DTE Female DCE Male DTE Cisco Cable Part Number CAB-SS-V35FC CAB-SS-V35FT CAB-SS-V35MC CAB-SS-V35MT CAB-SS-X21FC CAB-SS-X21MT Platform Support for Cisco Interface Cards Product Description Cisco Product ID Analog Modem WAN ...-2AM Supported on Cisco Routers See Document Cisco 1721 Cisco 1751 Cisco 1760 Cisco 1800 series (modular) Cisco 2600 series Cisco 2800 series Cisco 3600 series Cisco 3700 series Cisco 3800 series Cisco 1721 Cisco 1751 Cisco 1760 Cisco 1800 series (modular) Cisco 2600 series Cisco 2800 series Cisco 3600 series Cisco 3700 series Cisco 3800 series Analog Modem...
... DTE Female DCE Male DTE Cisco Cable Part Number CAB-SS-V35FC CAB-SS-V35FT CAB-SS-V35MC CAB-SS-V35MT CAB-SS-X21FC CAB-SS-X21MT Platform Support for Cisco Interface Cards Product Description Cisco Product ID Analog Modem WAN ...-2AM Supported on Cisco Routers See Document Cisco 1721 Cisco 1751 Cisco 1760 Cisco 1800 series (modular) Cisco 2600 series Cisco 2800 series Cisco 3600 series Cisco 3700 series Cisco 3800 series Cisco 1721 Cisco 1751 Cisco 1760 Cisco 1800 series (modular) Cisco 2600 series Cisco 2800 series Cisco 3600 series Cisco 3700 series Cisco 3800 series Analog Modem...
Hardware Installation Guide
Page 38
Cisco 3600 series - Cisco 2600 series - Cisco 3700 series Tip For information on installing interface cards on network modules, see the "Installing Cisco Interface Cards in the same chassis as an ISDN PRI network module. The following Cisco access routers may require interface card ...the interface card: • Cisco 2800 series routers • Cisco 3800 series routers OL-12842-01 6 Tools and Equipment Required During Cisco Interface Card Installation You will need the following tools and equipment while working with Cisco interface cards: • Number 1 Phillips screwdriver or a ...
Cisco 3600 series - Cisco 2600 series - Cisco 3700 series Tip For information on installing interface cards on network modules, see the "Installing Cisco Interface Cards in the same chassis as an ISDN PRI network module. The following Cisco access routers may require interface card ...the interface card: • Cisco 2800 series routers • Cisco 3800 series routers OL-12842-01 6 Tools and Equipment Required During Cisco Interface Card Installation You will need the following tools and equipment while working with Cisco interface cards: • Number 1 Phillips screwdriver or a ...
Hardware Installation Guide
Page 39
...Step 2 (For interface card slots that contained double-wide interface cards) Install a slot divider in Table 6. Note Blank interface module faceplates are for Cisco Access Routers. To install a blank faceplate over an interface card slot set up for a double-wide interface card, you plan to use . (See... Remove the blank faceplates from the slots you plan to (See the "Removing Blank Faceplates" section on page 8.) use . Using either a number 1 Phillips screwdriver or a small flat-blade screwdriver, tighten the captive screws until the blank faceplate is flush with the threaded holes on the ...
...Step 2 (For interface card slots that contained double-wide interface cards) Install a slot divider in Table 6. Note Blank interface module faceplates are for Cisco Access Routers. To install a blank faceplate over an interface card slot set up for a double-wide interface card, you plan to use . (See... Remove the blank faceplates from the slots you plan to (See the "Removing Blank Faceplates" section on page 8.) use . Using either a number 1 Phillips screwdriver or a small flat-blade screwdriver, tighten the captive screws until the blank faceplate is flush with the threaded holes on the ...
Hardware Installation Guide
Page 40
Removing Blank Faceplates To remove blank faceplates, perform the following steps: Step 1 Using either a number 1 Phillips screwdriver or a small flat-blade screwdriver, unscrew the captive screws and remove the blank faceplate from the ...slot. Step 4 Continue with hardware installation tasks. Step 2 Continue with hardware installation tasks. OL-12842-01 8 Installing Cisco Interface Cards in Cisco Access Routers Installing Cisco Interface Cards in Cisco Access Routers Figure 17 Installing a Blank Interface Card Faceplate 121073 1 1 Blank interface card faceplate Step 3 Repeat for ...
Removing Blank Faceplates To remove blank faceplates, perform the following steps: Step 1 Using either a number 1 Phillips screwdriver or a small flat-blade screwdriver, unscrew the captive screws and remove the blank faceplate from the ...slot. Step 4 Continue with hardware installation tasks. Step 2 Continue with hardware installation tasks. OL-12842-01 8 Installing Cisco Interface Cards in Cisco Access Routers Installing Cisco Interface Cards in Cisco Access Routers Figure 17 Installing a Blank Interface Card Faceplate 121073 1 1 Blank interface card faceplate Step 3 Repeat for ...
Hardware Installation Guide
Page 48
Installing Cisco Interface Cards in Cisco Access Routers Installing Cisco Interface Cards in Cisco Access Routers Figure 25 1 Installing Single-Wide Interface Cards in to channel ESD voltages to ground. Proceed with connecting ...off electrical power and disconnect network cables from the router. Step 7 Step 8 Using a number 1 Phillips or flat-blade screwdriver, tighten the captive mounting screws on locating additional hardware documentation. Leave the power cable plugged in Cisco Access Routers 2 121080 1 Interface card 2 Card guides Step 6 Using the faceplate, push...
Installing Cisco Interface Cards in Cisco Access Routers Installing Cisco Interface Cards in Cisco Access Routers Figure 25 1 Installing Single-Wide Interface Cards in to channel ESD voltages to ground. Proceed with connecting ...off electrical power and disconnect network cables from the router. Step 7 Step 8 Using a number 1 Phillips or flat-blade screwdriver, tighten the captive mounting screws on locating additional hardware documentation. Leave the power cable plugged in Cisco Access Routers 2 121080 1 Interface card 2 Card guides Step 6 Using the faceplate, push...
Hardware Installation Guide
Page 49
... card board. OL-12842-01 17 The interface card faceplate should contact the chassis rear panel. Step 7 Step 8 Using a number 1 Phillips or flat-blade screwdriver, tighten the captive mounting screws on the router backplane. Tip See the "Where to Go Next...blank faceplates for future use . (See the "Removing Blank Faceplates" section on locating additional hardware documentation. Installing Cisco Interface Cards in Cisco Access Routers Installing Cisco Interface Cards in Cisco Access Routers Step 3 Remove the blank faceplates installed over the slot you intend to use . Step 4 ...
... card board. OL-12842-01 17 The interface card faceplate should contact the chassis rear panel. Step 7 Step 8 Using a number 1 Phillips or flat-blade screwdriver, tighten the captive mounting screws on the router backplane. Tip See the "Where to Go Next...blank faceplates for future use . (See the "Removing Blank Faceplates" section on locating additional hardware documentation. Installing Cisco Interface Cards in Cisco Access Routers Installing Cisco Interface Cards in Cisco Access Routers Step 3 Remove the blank faceplates installed over the slot you intend to use . Step 4 ...
Hardware Installation Guide
Page 51
... Cards in Cisco Access Routers Installing Cisco Interface Cards in a Network Module (Typical) 2E 2W W1 H7219 B1 B2 BRI S/T 1 ETH 1 ACT LNK ACT LNK WO ETHERNET 0 AUI EN 2 1 Interface card 2 2-slot network module Step 5 Step 6 Using a number 1 Phillips or flat-blade screwdriver, tighten ...the captive mounting screws into the connector on the module. (See Figure 28.) Figure 28 Installing an Interface Card in Cisco Network Modules Step 3 Using a number 1 Phillips or flat-blade screwdriver, loosen the screws on the network module faceplate. Statement 8 OL-12842-01 19 Reinstall...
... Cards in Cisco Access Routers Installing Cisco Interface Cards in a Network Module (Typical) 2E 2W W1 H7219 B1 B2 BRI S/T 1 ETH 1 ACT LNK ACT LNK WO ETHERNET 0 AUI EN 2 1 Interface card 2 2-slot network module Step 5 Step 6 Using a number 1 Phillips or flat-blade screwdriver, tighten ...the captive mounting screws into the connector on the module. (See Figure 28.) Figure 28 Installing an Interface Card in Cisco Network Modules Step 3 Using a number 1 Phillips or flat-blade screwdriver, loosen the screws on the network module faceplate. Statement 8 OL-12842-01 19 Reinstall...
Hardware Installation Guide
Page 52
... the wire from the router. Statement 7 Step 2 Remove all power is removed from the DC circuit. Step 3 Step 4 Using a number 1 Phillips or flat-blade screwdriver, loosen the captive mounting screws on the interface card faceplate. Warning Before performing any of the following actions...To remove or replace an interface card from the network module. Removing or Replacing Cisco Interface Cards for Cisco Access Routers Installing Cisco Interface Cards in Cisco Access Routers Removing or Replacing Cisco Interface Cards for the slot or network module you intend to use the procedures...
... the wire from the router. Statement 7 Step 2 Remove all power is removed from the DC circuit. Step 3 Step 4 Using a number 1 Phillips or flat-blade screwdriver, loosen the captive mounting screws on the interface card faceplate. Warning Before performing any of the following actions...To remove or replace an interface card from the network module. Removing or Replacing Cisco Interface Cards for Cisco Access Routers Installing Cisco Interface Cards in Cisco Access Routers Removing or Replacing Cisco Interface Cards for the slot or network module you intend to use the procedures...
Hardware Installation Guide
Page 55
...the interface card faceplate makes contact with the guides in the MRP or ASI 81 card, use . Installing Cisco Interface Cards in Cisco Access Routers Installing Cisco Interface Cards on the Cisco ICS 7750 Step 7 If you feel its edge connector seat securely into the connector on the MRP or... ASI 81 card. Tip Save the blank faceplate for future use either a number 2 Phillips screwdriver or a small flat-blade ...
...the interface card faceplate makes contact with the guides in the MRP or ASI 81 card, use . Installing Cisco Interface Cards in Cisco Access Routers Installing Cisco Interface Cards on the Cisco ICS 7750 Step 7 If you feel its edge connector seat securely into the connector on the MRP or... ASI 81 card. Tip Save the blank faceplate for future use either a number 2 Phillips screwdriver or a small flat-blade ...
Hardware Installation Guide
Page 76
...: Note You can distinguish between WIC36 and WIC models of an ISDN BRI WIC by the location and labeling of the LEDs and by the number and location of cutouts in the faceplate. • 1-port ISDN BRI WIC with S/T interface (WIC36-1B-S/T) (see Figure 44) • 1-port ISDN BRI WIC with...
...: Note You can distinguish between WIC36 and WIC models of an ISDN BRI WIC by the location and labeling of the LEDs and by the number and location of cutouts in the faceplate. • 1-port ISDN BRI WIC with S/T interface (WIC36-1B-S/T) (see Figure 44) • 1-port ISDN BRI WIC with...
Hardware Installation Guide
Page 80
...: Note You can distinguish between WIC36 and WIC models of an ISDN BRI WIC by the location and labeling of the LEDs and by the number and location of cutouts in the faceplate. • 1-port ISDN BRI WIC with integrated NT1 device (WIC36-1B-U) (see Figure 49) • 1-port ISDN BRI...
...: Note You can distinguish between WIC36 and WIC models of an ISDN BRI WIC by the location and labeling of the LEDs and by the number and location of cutouts in the faceplate. • 1-port ISDN BRI WIC with integrated NT1 device (WIC36-1B-U) (see Figure 49) • 1-port ISDN BRI...
Hardware Installation Guide
Page 103
...a 2-port card with a port for ADSLoPOTS and a data-only backup port for an ISDN BRI S/T connection Note ADSL HWICs can be inserted only in Cisco's standard single-wide HWIC form factor. ADSL HWICs are supported. DSL Interface Cards ADSL High Speed WICs (HWICs) EN L0, L1, L2, L3 Status ... following variations: • ADSL over ISDN (ADSLoISDN) HWICs - ADSL HWICs are enabled to receive HWICs, refer to the Interface Card Slot Locations and Numbering on Cisco.com. You must have forgotten your router are available in your username or password, click Cancel at http://www...
...a 2-port card with a port for ADSLoPOTS and a data-only backup port for an ISDN BRI S/T connection Note ADSL HWICs can be inserted only in Cisco's standard single-wide HWIC form factor. ADSL HWICs are supported. DSL Interface Cards ADSL High Speed WICs (HWICs) EN L0, L1, L2, L3 Status ... following variations: • ADSL over ISDN (ADSLoISDN) HWICs - ADSL HWICs are enabled to receive HWICs, refer to the Interface Card Slot Locations and Numbering on Cisco.com. You must have forgotten your router are available in your username or password, click Cancel at http://www...
Hardware Installation Guide
Page 119
... 4-port FXS/DID cards (VIC-4FXS/DID) only to the station. For information about using analog DID with a Ringer Equivalence Number (REN) load of 1 or less. Note The Cisco ICS 7750 also supports 8 FXS ports on the analog station interface 81 (ASI 81), and 16 FXS ports on page 13....IN USE 41218 OL-12847-01 3 Note Each port on the 4-port FXS/DID cards in Cisco IOS Release 12.3(14)T and later. Note Cisco 2600XM series, Cisco 2691, Cisco 2800 series, Cisco 3600 series, Cisco 3700 series, and Cisco 3800 series routers support DID on the 4-port FXS/DID VIC can support four 4-port FXS/...
... 4-port FXS/DID cards (VIC-4FXS/DID) only to the station. For information about using analog DID with a Ringer Equivalence Number (REN) load of 1 or less. Note The Cisco ICS 7750 also supports 8 FXS ports on the analog station interface 81 (ASI 81), and 16 FXS ports on page 13....IN USE 41218 OL-12847-01 3 Note Each port on the 4-port FXS/DID cards in Cisco IOS Release 12.3(14)T and later. Note Cisco 2600XM series, Cisco 2691, Cisco 2800 series, Cisco 3600 series, Cisco 3700 series, and Cisco 3800 series routers support DID on the 4-port FXS/DID VIC can support four 4-port FXS/...
Hardware Installation Guide
Page 128
... one end of the cable to a TE device, the cable must have the transmit and receive pins swapped (crossover cable). Pin 6/T- Table 25 Interface Pin Numbers and Functions ISDN BRI NT/TE Card NT Interface1 Pin 3/T+ Pin 3/R+ Pin 4/R+ Pin 4/T+ Pin 5/R- See Table 25. Use a straight-through RJ-45-to-RJ-45...
... one end of the cable to a TE device, the cable must have the transmit and receive pins swapped (crossover cable). Pin 6/T- Table 25 Interface Pin Numbers and Functions ISDN BRI NT/TE Card NT Interface1 Pin 3/T+ Pin 3/R+ Pin 4/R+ Pin 4/T+ Pin 5/R- See Table 25. Use a straight-through RJ-45-to-RJ-45...