Configuration Guide
Page 1
...). The source of the CPU, memory, and interfaces. 2 The system bootstrap software (boot image) executes and searches for the configuration register is determined by the configuration register setting. Configuring the Cisco 2524 and Cisco 2525 Routers 4-1 CHAPTER 4 Configuring the Cisco 2524 and Cisco 2525 Routers This chapter describes how to configure the Cisco 2524 and Cisco 2525 routers and contains the following boot...
...). The source of the CPU, memory, and interfaces. 2 The system bootstrap software (boot image) executes and searches for the configuration register is determined by the configuration register setting. Configuring the Cisco 2524 and Cisco 2525 Routers 4-1 CHAPTER 4 Configuring the Cisco 2524 and Cisco 2525 Routers This chapter describes how to configure the Cisco 2524 and Cisco 2525 routers and contains the following boot...
Configuration Guide
Page 2
... configuration file is not found in Flash memory, the router reverts to boot ROM mode (which is used to configure the router. 4-2 Cisco 2524 and Cisco 2525 Router User Guide For normal router operation, there must be a valid Cisco IOS image in Flash memory and a configuration file in NVRAM. Configuring the Router 3 If after five attempts a valid Cisco IOS image is not found in...
... configuration file is not found in Flash memory, the router reverts to boot ROM mode (which is used to configure the router. 4-2 Cisco 2524 and Cisco 2525 Router User Guide For normal router operation, there must be a valid Cisco IOS image in Flash memory and a configuration file in NVRAM. Configuring the Router 3 If after five attempts a valid Cisco IOS image is not found in...
Configuration Guide
Page 5
... 2 Turn ON power to operate. This will automatically start the setup command facility. Many prompts in NVRAM. Configuring the Cisco 2524 and Cisco 2525 Routers 4-5 If the remote end of the WAN connection is not set up to run the AutoInstall process. Step 3 Enter... router to determine that the AutoInstall process created in square brackets following the question. The router will begin. Configuring the Router Take the following steps to prepare your network. This section gives an example configuration using AutoInstall, the router will prevent the router from Flash memory....
... 2 Turn ON power to operate. This will automatically start the setup command facility. Many prompts in NVRAM. Configuring the Cisco 2524 and Cisco 2525 Routers 4-5 If the remote end of the WAN connection is not set up to run the AutoInstall process. Step 3 Enter... router to determine that the AutoInstall process created in square brackets following the question. The router will begin. Configuring the Router Take the following steps to prepare your network. This section gives an example configuration using AutoInstall, the router will prevent the router from Flash memory....
Configuration Guide
Page 7
... 52.227-19 and subparagraph (c) (1) (ii) of memory. Cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) X000 Software (IGS...3 Press Return or enter yes to begin the configuration process. Configuring the Cisco 2524 and Cisco 2525 Routers 4-7 SuperLAT software copyright 1990 by TGV Inc). for additional help . TN3270...Configuring the Router Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of processor board System flash (Read ONLY...
... 52.227-19 and subparagraph (c) (1) (ii) of memory. Cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS (tm) X000 Software (IGS...3 Press Return or enter yes to begin the configuration process. Configuring the Cisco 2524 and Cisco 2525 Routers 4-7 SuperLAT software copyright 1990 by TGV Inc). for additional help . TN3270...Configuring the Router Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of processor board System flash (Read ONLY...
Configuration Guide
Page 20
... of the Cisco IOS image: Router> enable Password: enablepassword Router# configure terminal Router (config)# boot system flash filename Router (config)# Ctrl-Z Router# copy running -config startup-config Building configuration ... [OK] Router# exit Router> 4-20 Cisco 2524 and Cisco 2525 Router User Guide The router boots using the first boot command that succeeds. If you load system software from a TFTP server on the network. 1 Flash memory Information...
... of the Cisco IOS image: Router> enable Password: enablepassword Router# configure terminal Router (config)# boot system flash filename Router (config)# Ctrl-Z Router# copy running -config startup-config Building configuration ... [OK] Router# exit Router> 4-20 Cisco 2524 and Cisco 2525 Router User Guide The router boots using the first boot command that succeeds. If you load system software from a TFTP server on the network. 1 Flash memory Information...
Configuration Guide
Page 21
... network interfaces. SuperLAT software copyright 199X by Cisco Systems, Inc. No module installed for Serial Interface 0 No module installed for Serial Interface 1 32K bytes of non-volatile configuration memory. 8192K bytes of memory. Checking the Configuration Settings Enter the show version...(copyright 199X by power-on System image file is "flash:XXX/XXX-X-X.Nov14", booted via flash Cisco XXXX(68030) processor (revision X) with 4092K/2048K bytes of processor board System flash (Read ONLY) Configuration register is 0x2102 Router> Configuring the Cisco 2524 and Cisco 2525 Routers 4-21
... network interfaces. SuperLAT software copyright 199X by Cisco Systems, Inc. No module installed for Serial Interface 0 No module installed for Serial Interface 1 32K bytes of non-volatile configuration memory. 8192K bytes of memory. Checking the Configuration Settings Enter the show version...(copyright 199X by power-on System image file is "flash:XXX/XXX-X-X.Nov14", booted via flash Cisco XXXX(68030) processor (revision X) with 4092K/2048K bytes of processor board System flash (Read ONLY) Configuration register is 0x2102 Router> Configuring the Cisco 2524 and Cisco 2525 Routers 4-21
Overview
Page 2
...; One Ethernet (AUI or 10BaseT) interface on the Cisco 2524 router • One Token Ring (STP or UTP) interface on the Cisco 2525 router • Dynamic random-access memory (DRAM) for main system memory and shared memory • Nonvolatile random-access memory (NVRAM) for storing configuration information • Flash memory for running Cisco IOS software • EIA/TIA-232 console port for...
...; One Ethernet (AUI or 10BaseT) interface on the Cisco 2524 router • One Token Ring (STP or UTP) interface on the Cisco 2525 router • Dynamic random-access memory (DRAM) for main system memory and shared memory • Nonvolatile random-access memory (NVRAM) for storing configuration information • Flash memory for running Cisco IOS software • EIA/TIA-232 console port for...