Hardware Installation Guide
Page 145
...interface cards to connect it is not actually performed at the same speed and in the same duplex mode. or half-duplex) of Cisco interface cards used for Cisco access routers see the Cisco Interface Cards for Cisco Access Routers document. The following sections: • WIC-4ESW Card, page 1 • WIC-1ENET Interface...to the host, and is connected and then operates at the switch.) The ports autosense the speed (10 Mbps or 100 Mbps) and duplex mode (full- It contains the following subsections are included: • WIC-4ESW Interface Card Port Numbering, page 2 • WIC-4ESW...
...interface cards to connect it is not actually performed at the same speed and in the same duplex mode. or half-duplex) of Cisco interface cards used for Cisco access routers see the Cisco Interface Cards for Cisco Access Routers document. The following sections: • WIC-4ESW Card, page 1 • WIC-1ENET Interface...to the host, and is connected and then operates at the switch.) The ports autosense the speed (10 Mbps or 100 Mbps) and duplex mode (full- It contains the following subsections are included: • WIC-4ESW Interface Card Port Numbering, page 2 • WIC-4ESW...
Hardware Installation Guide
Page 148
... protocol • Web-based management interface • Remote Monitoring (RMON) WIC-1ENET Interface Card This section describes how to connect the Cisco 1-port Ethernet interface card supporting 10BASE-T Ethernet (WIC-1ENET), and contains the following sections: • WIC-1ENET Interface Card LED, ..., page 5 • WIC-1ENET Full-Duplex and Half-Duplex, page 6 The 1-port Ethernet interface card provides the router with additional Ethernet interfaces that can use the functionality of the Cisco IOS software with any type of the router indicates that data is up. Additionally, the...
... protocol • Web-based management interface • Remote Monitoring (RMON) WIC-1ENET Interface Card This section describes how to connect the Cisco 1-port Ethernet interface card supporting 10BASE-T Ethernet (WIC-1ENET), and contains the following sections: • WIC-1ENET Interface Card LED, ..., page 5 • WIC-1ENET Full-Duplex and Half-Duplex, page 6 The 1-port Ethernet interface card provides the router with additional Ethernet interfaces that can use the functionality of the Cisco IOS software with any type of the router indicates that data is up. Additionally, the...
Hardware Installation Guide
Page 150
...password, click Cancel at http://www.cisco.com/go/fn. Supported Platforms LAN Interface Cards WIC-1ENET Full-Duplex and Half-Duplex The WIC-1ENET is attached to full-duplex mode. You can be put into half-duplex mode by a Cisco interface card refer to put the Ethernet... interface into full-duplex operation. You must also set (10 sec) Half-duplex, 10BaseT .... Finding Support Information for Cisco Interface Cards. OL-12849-01 6 Use the full-duplex command to Platform Support for Platforms and Cisco IOS Software Images Use Cisco Feature Navigator to put ...
...password, click Cancel at http://www.cisco.com/go/fn. Supported Platforms LAN Interface Cards WIC-1ENET Full-Duplex and Half-Duplex The WIC-1ENET is attached to full-duplex mode. You can be put into half-duplex mode by a Cisco interface card refer to put the Ethernet... interface into full-duplex operation. You must also set (10 sec) Half-duplex, 10BaseT .... Finding Support Information for Cisco Interface Cards. OL-12849-01 6 Use the full-duplex command to Platform Support for Platforms and Cisco IOS Software Images Use Cisco Feature Navigator to put ...
Hardware Installation Guide
Page 163
...HWIC-1FE and HWIC-2FE faceplates, and Table 33 describes the functions of router slot 0 is represented as: interface FastEthernet 0/1/0 Fast Ethernet HWICs LEDs ...detected Off = No link pulses detected Blinking = Transmit or receive activity OL-12851-01 3 or half-duplex operation, collisions, speed, transmit/receive activity, and link status. Figure 113 HWIC-1FE Faceplate 158059 HWIC-...-2FE Faceplate FDX/COL 100 HWIC- and 2-Port Fast Ethernet High-Speed WAN Interface Cards Cisco 1- Modules and interface cards are identified by three digits: slot number/subslot number/port number...
...HWIC-1FE and HWIC-2FE faceplates, and Table 33 describes the functions of router slot 0 is represented as: interface FastEthernet 0/1/0 Fast Ethernet HWICs LEDs ...detected Off = No link pulses detected Blinking = Transmit or receive activity OL-12851-01 3 or half-duplex operation, collisions, speed, transmit/receive activity, and link status. Figure 113 HWIC-1FE Faceplate 158059 HWIC-...-2FE Faceplate FDX/COL 100 HWIC- and 2-Port Fast Ethernet High-Speed WAN Interface Cards Cisco 1- Modules and interface cards are identified by three digits: slot number/subslot number/port number...