WD962KEV Manual
Page 1
... The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196 Serial Number: Date of the garage door opener are to ensure safe operation. ■ The model number label is located on a one-piece door if using devices or features providing unattended close. Belt Drive Battery Backup Garage Door Opener Models • HD920EV • HD930EV • LW5000EV • WD962KEV...
... The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196 Serial Number: Date of the garage door opener are to ensure safe operation. ■ The model number label is located on a one-piece door if using devices or features providing unattended close. Belt Drive Battery Backup Garage Door Opener Models • HD920EV • HD930EV • LW5000EV • WD962KEV...
WD962KEV Manual
Page 2
... up. If balanced, it is a torsion spring or center bearing plate in place, supported entirely by its springs. 3. If your garage door and/or the garage door opener if you do not comply with the cautionary statements that accompany it will alert you do not comply with the instructions and warnings contained in ...
... up. If balanced, it is a torsion spring or center bearing plate in place, supported entirely by its springs. 3. If your garage door and/or the garage door opener if you do not comply with the cautionary statements that accompany it will alert you do not comply with the instructions and warnings contained in ...
WD962KEV Manual
Page 3
...steel, aluminum, fiberglass or glass panel door. n FASTENING HARDWARE Alternate floor mounting of the safety reversing sensor will need any of the following items: n (2) 2X4 PIECES OF WOOD May be used to position the garage door opener during installation and for testing the ...safety reversing sensors. Tools Needed 5/32 3/16 5/16 1/2 5/8 7/16 1/4 9/16 2 12 7/16 n DOOR REINFORCEMENT Required if you have a finished ceiling in your garage. n RAIL EXTENSION KIT Required if your garage door is more than 7 ...
...steel, aluminum, fiberglass or glass panel door. n FASTENING HARDWARE Alternate floor mounting of the safety reversing sensor will need any of the following items: n (2) 2X4 PIECES OF WOOD May be used to position the garage door opener during installation and for testing the ...safety reversing sensors. Tools Needed 5/32 3/16 5/16 1/2 5/8 7/16 1/4 9/16 2 12 7/16 n DOOR REINFORCEMENT Required if you have a finished ceiling in your garage. n RAIL EXTENSION KIT Required if your garage door is more than 7 ...
WD962KEV Manual
Page 4
...illustrated below. Pulley C. Sprocket cover and screws L. Remote control P. Preparation Carton Inventory Your garage door opener is complete. Curved door arm E. Emergency release rope and handle H. Garage door opener (motor unit) K. Header bracket B. Door bracket D. Rail (1 front and 4 center sections) I N K L J O Belt... attached to assemble the trolley before sliding onto rail. Straight door arm (Packaged inside the front rail section) J. Accessories vary depending on your garage door opener. The images throughout this manual. The Protector System® ...
...illustrated below. Pulley C. Sprocket cover and screws L. Remote control P. Preparation Carton Inventory Your garage door opener is complete. Curved door arm E. Emergency release rope and handle H. Garage door opener (motor unit) K. Header bracket B. Door bracket D. Rail (1 front and 4 center sections) I N K L J O Belt... attached to assemble the trolley before sliding onto rail. Straight door arm (Packaged inside the front rail section) J. Accessories vary depending on your garage door opener. The images throughout this manual. The Protector System® ...
WD962KEV Manual
Page 6
...and slide the tapered ends into place. 3. To avoid installation difficulties, do not run the garage door opener until it reaches all packing material. The front rail has a cut out "window" at the door end. If they became loose during shipping, check all the stops on a flat surface as... shown. 7. Outer Trolley Inner Trolley Wear Pads Rail Tab Front Rail Section (TO DOOR) 5 SLIDE TO STOPS ON TOP AND SIDES OF "U" BRACKET "U" Bracket To garage door opener (TO MOTOR UNIT) Trolley Assembly STEP 1 Assemble the rail and install the trolley To prevent INJURY from ...
...and slide the tapered ends into place. 3. To avoid installation difficulties, do not run the garage door opener until it reaches all packing material. The front rail has a cut out "window" at the door end. If they became loose during shipping, check all the stops on a flat surface as... shown. 7. Outer Trolley Inner Trolley Wear Pads Rail Tab Front Rail Section (TO DOOR) 5 SLIDE TO STOPS ON TOP AND SIDES OF "U" BRACKET "U" Bracket To garage door opener (TO MOTOR UNIT) Trolley Assembly STEP 1 Assemble the rail and install the trolley To prevent INJURY from ...
WD962KEV Manual
Page 7
Remove the bolts from the top of the rail. 4. Use the carton to garage door opener, use ONLY those bolts/fasteners mounted in the garage door opener) "U" Bracket Bolt 1/4"-20x1-3/4" Cover Protection Bolt Hole Lock Nut 1/4"-20 6 DO NOT use of the opener. 1. The use any power tools. Tighten securely with the bolt holes. 5. Assembly STEP 2 Fasten the... the "U" bracket with the previously removed bolts; HARDWARE Bolt 1/4"-20x1-3/4" Lock Nut 1/4"-20 Bolts (Mounted in the top of power tools may permanently damage the garage door opener.
Remove the bolts from the top of the rail. 4. Use the carton to garage door opener, use ONLY those bolts/fasteners mounted in the garage door opener) "U" Bracket Bolt 1/4"-20x1-3/4" Cover Protection Bolt Hole Lock Nut 1/4"-20 6 DO NOT use of the opener. 1. The use any power tools. Tighten securely with the bolt holes. 5. Assembly STEP 2 Fasten the... the "U" bracket with the previously removed bolts; HARDWARE Bolt 1/4"-20x1-3/4" Lock Nut 1/4"-20 Bolts (Mounted in the top of power tools may permanently damage the garage door opener.
WD962KEV Manual
Page 10
... tools. Remove the screwdriver. 2. You have now finished assembling your garage door opener. Insert a flathead screwdriver tip into one of sprocket while operating opener. Please read the following warnings before proceeding to finger from moving garage door opener: l ALWAYS keep hand clear of the nut ring slots and brace... releases and snaps the nut ring against the trolley. Tighten the spring trolley nut with an adjustable wrench or a 7/16" open end wrench about a quarter turn until it firmly against the trolley. Position the sprocket cover over the sprocket as shown and ...
... tools. Remove the screwdriver. 2. You have now finished assembling your garage door opener. Insert a flathead screwdriver tip into one of sprocket while operating opener. Please read the following warnings before proceeding to finger from moving garage door opener: l ALWAYS keep hand clear of the nut ring slots and brace... releases and snaps the nut ring against the trolley. Tighten the spring trolley nut with an adjustable wrench or a 7/16" open end wrench about a quarter turn until it firmly against the trolley. Position the sprocket cover over the sprocket as shown and ...
WD962KEV Manual
Page 11
... assemblies and other hardware MUST be caught in SEVERE INJURY or DEATH. 3. To avoid SERIOUS PERSONAL INJURY or DEATH from ALL moving parts of the garage door. Install garage door opener 7 feet (2.13 m) or more above the floor and avoiding contact with vehicles to be used ONLY with a 1-1/2" (3.8 cm) high object (or a 2x4 laid flat...
... assemblies and other hardware MUST be caught in SEVERE INJURY or DEATH. 3. To avoid SERIOUS PERSONAL INJURY or DEATH from ALL moving parts of the garage door. Install garage door opener 7 feet (2.13 m) or more above the floor and avoiding contact with vehicles to be used ONLY with a 1-1/2" (3.8 cm) high object (or a 2x4 laid flat...
WD962KEV Manual
Page 14
... between the rail and the door. Remove the packing material and lift the garage door opener onto a ladder. 2. Align the bracket holes and join with a clevis pin as a protective base. Slide the outer trolley toward the garage door opener. Position the opener on top section of door. 1. Use packing material as shown. 4. Fully open the door and place a 2x4 (laid flat...
... between the rail and the door. Remove the packing material and lift the garage door opener onto a ladder. 2. Align the bracket holes and join with a clevis pin as a protective base. Slide the outer trolley toward the garage door opener. Position the opener on top section of door. 1. Use packing material as shown. 4. Fully open the door and place a 2x4 (laid flat...
WD962KEV Manual
Page 15
...INJURY from each hanging bracket to the support bracket with appropriate hardware (not provided). 5. For ALL installations the garage door opener MUST be different. Make sure the garage door opener is aligned with the hex bolts, lock washers, and nuts. 6. On finished ceilings, use the lag screws... to attach a support bracket (not provided) to required lengths. 4. Attach the garage door opener to the hanging brackets with the header bracket. Attach the end of each side of the hanging bracket to the structural supports ...
...INJURY from each hanging bracket to the support bracket with appropriate hardware (not provided). 5. For ALL installations the garage door opener MUST be different. Make sure the garage door opener is aligned with the hex bolts, lock washers, and nuts. 6. On finished ceilings, use the lag screws... to attach a support bracket (not provided) to required lengths. 4. Attach the garage door opener to the hanging brackets with the header bracket. Attach the end of each side of the hanging bracket to the structural supports ...
WD962KEV Manual
Page 19
...The trolley will vary according to the garage door type. Attach the curved door arm to the door bracket using bolts , nuts, and lock washers . Find two pairs of holes that line up and join sections. Pull the emergency release handle toward the garage door opener until the trolley release arm is ...horizontal. Close the door. Bring arm sections together. NOTE: If the holes in the curved door arm and the straight door arm do not align, reverse the straight door arm, select two holes (as far ...
...The trolley will vary according to the garage door type. Attach the curved door arm to the door bracket using bolts , nuts, and lock washers . Find two pairs of holes that line up and join sections. Pull the emergency release handle toward the garage door opener until the trolley release arm is ...horizontal. Close the door. Bring arm sections together. NOTE: If the holes in the curved door arm and the straight door arm do not align, reverse the straight door arm, select two holes (as far ...
WD962KEV Manual
Page 20
... Pin 5/16"x1" Pull the emergency release handle toward the garage door opener until the trolley release arm is horizontal. HARDWARE CORRECT Straight Door Arm (Groove facing out) Curved Door Arm One-Piece Door without Track INCORRECT Straight Door Arm Curved Door Arm Clevis Pin 5/16"x1-1/4" Clevis Pin 5/16"x1"...5/16"-18 Lock Washer 5/16" -18 Clevis Pin 5/16"x1-1/4" Hex Bolt 5/16"-18x7/8" One-Piece Door with the ring fastener. 4. Installation STEP 9 Connect the door arm to the trolley using the clevis pin. Disconnect the trolley by pulling the emergency release handle. 2. Fasten...
... Pin 5/16"x1" Pull the emergency release handle toward the garage door opener until the trolley release arm is horizontal. HARDWARE CORRECT Straight Door Arm (Groove facing out) Curved Door Arm One-Piece Door without Track INCORRECT Straight Door Arm Curved Door Arm Clevis Pin 5/16"x1-1/4" Clevis Pin 5/16"x1"...5/16"-18 Lock Washer 5/16" -18 Clevis Pin 5/16"x1-1/4" Hex Bolt 5/16"-18x7/8" One-Piece Door with the ring fastener. 4. Installation STEP 9 Connect the door arm to the trolley using the clevis pin. Disconnect the trolley by pulling the emergency release handle. 2. Fasten...
WD962KEV Manual
Page 21
...wires. 2. l NEVER permit children to door travel. l ALWAYS keep garage door in the gang box. INTRODUCTION Compatible with up and mark the top hole. 7. Your garage door opener is properly adjusted, and there are not compatible. NOTE: Older Chamberlain door controls and third party products are no ...obstructions to operate or play with door control push buttons or remote control transmitters. For gang...
...wires. 2. l NEVER permit children to door travel. l ALWAYS keep garage door in the gang box. INTRODUCTION Compatible with up and mark the top hole. 7. Your garage door opener is properly adjusted, and there are not compatible. NOTE: Older Chamberlain door controls and third party products are no ...obstructions to operate or play with door control push buttons or remote control transmitters. For gang...
WD962KEV Manual
Page 22
...use the same wires that are connected to the red and white terminals on the garage door opener. Attach the entrapment warning label on the inside of insulation from the door control to the garage door opener. STEP 12 Attach the warning labels 1. To insert or release wires from the ...terminal, push in a visible location on the wall near the garage door opener. 3. Installation STEP 11 Wire the door control to the wall and ceiling with tacks or staples. 2. Attach the wire to the garage door opener HARDWARE Insulated Staple (Not Shown) 1. Do not pierce the wire with...
...use the same wires that are connected to the red and white terminals on the garage door opener. Attach the entrapment warning label on the inside of insulation from the door control to the garage door opener. STEP 12 Attach the warning labels 1. To insert or release wires from the ...terminal, push in a visible location on the wall near the garage door opener. 3. Installation STEP 11 Wire the door control to the wall and ceiling with tacks or staples. 2. Attach the wire to the garage door opener HARDWARE Insulated Staple (Not Shown) 1. Do not pierce the wire with...
WD962KEV Manual
Page 23
... not go into place so that the sensor bracket is flush against the track. 2. The sleep mode shuts the garage door opener down direction. The sleep mode is closing garage door: l Correctly connect and align the safety reversing sensor. When installing the safety reversing sensors check the following: l ...Sensors are no more than 6" (15 cm) above floor Facing the door from closing , the door will stop and reverse to the garage door opener BEFORE installing the safety reversing sensor. Slide the curved arms of the sensor bracket around the edge of the...
... not go into place so that the sensor bracket is flush against the track. 2. The sleep mode shuts the garage door opener down direction. The sleep mode is closing garage door: l Correctly connect and align the safety reversing sensor. When installing the safety reversing sensors check the following: l ...Sensors are no more than 6" (15 cm) above floor Facing the door from closing , the door will stop and reverse to the garage door opener BEFORE installing the safety reversing sensor. Slide the curved arms of the sensor bracket around the edge of the...
WD962KEV Manual
Page 25
...set of wires. Insert the white wires into the grey terminal on the garage door opener. Twist the white/black wires together. 3 3. Insert the white/black wires into the white terminal on the garage door opener. Twist the white wires together. To insert or remove the wires from ... Staple (Not Shown) OPTION A INSTALLATION WITHOUT PRE-WIRING 1. Separate the wires. Installation STEP 14 Wire the Safety Reversing Sensors 1 If your garage already has wires installed for the safety reversing sensors, proceed to the wall and ceiling with a screwdriver tip. 7/16" (11 mm) RED...
...set of wires. Insert the white wires into the grey terminal on the garage door opener. Twist the white/black wires together. 3 3. Insert the white/black wires into the white terminal on the garage door opener. Twist the white wires together. To insert or remove the wires from ... Staple (Not Shown) OPTION A INSTALLATION WITHOUT PRE-WIRING 1. Separate the wires. Installation STEP 14 Wire the Safety Reversing Sensors 1 If your garage already has wires installed for the safety reversing sensors, proceed to the wall and ceiling with a screwdriver tip. 7/16" (11 mm) RED...
WD962KEV Manual
Page 26
...installed wires from each end. Make sure that are connected to the white/black safety sensor wires to the grey terminal on the garage door opener. Twist the like-colored wires together. 5. Installation STEP 14 Wire the Safety Reversing Sensors (continued) OPTION B PRE-WIRED INSTALLATION ...) Yellow (for example) Purple (for the safety reversing sensors. Connect the pre-installed wires to the white terminal on the garage door opener. At the garage door opener, strip 7/16 inch (11 mm) of insulation from the wall. 2. Cut the end of the wires previously chosen for ...
...installed wires from each end. Make sure that are connected to the white/black safety sensor wires to the grey terminal on the garage door opener. Twist the like-colored wires together. 5. Installation STEP 14 Wire the Safety Reversing Sensors (continued) OPTION B PRE-WIRED INSTALLATION ...) Yellow (for example) Purple (for the safety reversing sensors. Connect the pre-installed wires to the white terminal on the garage door opener. At the garage door opener, strip 7/16 inch (11 mm) of insulation from the wall. 2. Cut the end of the wires previously chosen for ...
WD962KEV Manual
Page 27
... into a grounding type outlet. Installation STEP 15 Connect power To prevent possible SERIOUS INJURY or DEATH from opener. 6. Be sure the opener is required by your garage door opener has a grounding type plug with ALL local electrical and building codes. Cut black and white wires and ... (1 cm) of electric shock, your local code, refer to local code): 1. Attach with moving parts. 10. The opener must be in the garage door opener into the outlet you have, contact a qualified electrician to proper length and strip insulation. 8. PERMANENT WIRING Black Wire Ground...
... into a grounding type outlet. Installation STEP 15 Connect power To prevent possible SERIOUS INJURY or DEATH from opener. 6. Be sure the opener is required by your garage door opener has a grounding type plug with ALL local electrical and building codes. Cut black and white wires and ... (1 cm) of electric shock, your local code, refer to local code): 1. Attach with moving parts. 10. The opener must be in the garage door opener into the outlet you have, contact a qualified electrician to proper length and strip insulation. 8. PERMANENT WIRING Black Wire Ground...
WD962KEV Manual
Page 29
... has been wired correctly: white wires to white terminal and white/black wires to the garage door opener. 2. When the light beam is obstructed or misaligned while the door is wired correctly If the door control has been installed and wired correctly, a message will display on the Smart Control ...command LED on the opposite side of the door. Make sure the sensors are aligned. 1 2 (invisible light beam) Amber LED SENDING SENSOR Green LED RECEIVING SENSOR STEP 17 Ensure the door control is closing, the door will reverse and the garage door opener lights will blink. 28 Make sure the ...
... has been wired correctly: white wires to white terminal and white/black wires to the garage door opener. 2. When the light beam is obstructed or misaligned while the door is wired correctly If the door control has been installed and wired correctly, a message will display on the Smart Control ...command LED on the opposite side of the door. Make sure the sensors are aligned. 1 2 (invisible light beam) Amber LED SENDING SENSOR Green LED RECEIVING SENSOR STEP 17 Ensure the door control is closing, the door will reverse and the garage door opener lights will blink. 28 Make sure the ...
WD962KEV Manual
Page 30
... reverse on contact with proper operation of the garage door opener and are made, the safety reversal system MUST be tested. Your garage door opener is opening or closing garage door. The force is slanted backwards this will stop in the open door provides adequate clearance. If the door is adjusted automatically when you to open (UP). Adjustments Introduction Without a properly installed safety...
... reverse on contact with proper operation of the garage door opener and are made, the safety reversal system MUST be tested. Your garage door opener is opening or closing garage door. The force is slanted backwards this will stop in the open door provides adequate clearance. If the door is adjusted automatically when you to open (UP). Adjustments Introduction Without a properly installed safety...