Extended Option Output Instruction Manual - English
Page 17
...of the instruction manual. •Create the timing chart showing ON and OFF of I/O in operation order. ,Based on and the preparation of machine operation is completed. 19 After the air pressure drop error is detected. 20 After split is completed (before moving to the next sewing start ...position). 21 After split is turned on the timing chart and condition number table (see instruction manual page 191-), create a program setting value table. ƒ...
...of the instruction manual. •Create the timing chart showing ON and OFF of I/O in operation order. ,Based on and the preparation of machine operation is completed. 19 After the air pressure drop error is detected. 20 After split is completed (before moving to the next sewing start ...position). 21 After split is turned on the timing chart and condition number table (see instruction manual page 191-), create a program setting value table. ƒ...
Network Users Manual - English
Page 95
... feed operation) After sewing is finished, the work clamp is not used . (This part is changed to ON. When using the STEP BACK switch. memo-09 Wiper is available by automatic ejector and the sewing machine automatically starts. memo-0E memo-0F Test feeding is carried out at a time is...-21 After the home position is detected and the machine moves to the sewing start position, the ç work clamp rises and then the feed plate returns to ON when the bobbin changer is available by means of two-stage work clamp switches. Used for software versions MN-C or later. BAS-311E.311EL...
... feed operation) After sewing is finished, the work clamp is not used . (This part is changed to ON. When using the STEP BACK switch. memo-09 Wiper is available by automatic ejector and the sewing machine automatically starts. memo-0E memo-0F Test feeding is carried out at a time is...-21 After the home position is detected and the machine moves to the sewing start position, the ç work clamp rises and then the feed plate returns to ON when the bobbin changer is available by means of two-stage work clamp switches. Used for software versions MN-C or later. BAS-311E.311EL...
Network Users Manual - English
Page 101
...parts adjustment 11. if a programmer is not possible (Panel PCB) E.61 Data cannot be backed up . Code Cause E.10 Emergency stop switch was pressed during sewing. The STEP BACK switch can then be formatted. E.12 E.20 E.21 E.22 E.30 E.31 E.32 Emergency stop switch once more to check if the machine...once more after turning the power off the power, wait a while and then turn the machine pulley Problem with machine motor stopping, or to cancel. Turn off the power and check the ground wire connection...the upper thread. Sewing can then resume. BAS-311E.311EL.326E.326EL 93
...parts adjustment 11. if a programmer is not possible (Panel PCB) E.61 Data cannot be backed up . Code Cause E.10 Emergency stop switch was pressed during sewing. The STEP BACK switch can then be formatted. E.12 E.20 E.21 E.22 E.30 E.31 E.32 Emergency stop switch once more to check if the machine...once more after turning the power off the power, wait a while and then turn the machine pulley Problem with machine motor stopping, or to cancel. Turn off the power and check the ground wire connection...the upper thread. Sewing can then resume. BAS-311E.311EL.326E.326EL 93
Network Users Manual - English
Page 112
...inserted and the emergency stop switch is activated, or it is turned on the power again. Parts to #d1-1, -1, -3 #1 The power lamp does not light when the power is ... • Refer to #1.1-5 • Refer to #1.1-2 X pulse motor control circuit board 104 BAS-311E.311EL.326E.326EL With error code [E.c0], the [MT] PROM on the control circuit board is...nothing changes, panel PCB is screwed into the heatsink on the power again. With error code [E.21], the machine is malfunctioning. • Check that generates strong electrical noise nearby. Chapter 7 Error status Probable causes...
...inserted and the emergency stop switch is activated, or it is turned on the power again. Parts to #d1-1, -1, -3 #1 The power lamp does not light when the power is ... • Refer to #1.1-5 • Refer to #1.1-2 X pulse motor control circuit board 104 BAS-311E.311EL.326E.326EL With error code [E.c0], the [MT] PROM on the control circuit board is...nothing changes, panel PCB is screwed into the heatsink on the power again. With error code [E.21], the machine is malfunctioning. • Check that generates strong electrical noise nearby. Chapter 7 Error status Probable causes...
Network Users Manual - English
Page 119
... is defective. 3. Check/repair/adjust Parts to be made. 1. The programmer is not properly adjusted. 2. Chapter 7 Error status Probable causes #17 The machine does not stop with a new one...grammed. #19 The operation will not stop if the emergency stop switch is canceled. #21 The STEP BACK switch is pressed. 1. The programmer connector and its cable are defective...Programmer Panel circuit board BAS-311E.311EL.326E.326EL 111 Panel circuit board #22 Sewing is complete, adjust the needle stop position varies at random every time the machine operation is not resumed...
... is defective. 3. Check/repair/adjust Parts to be made. 1. The programmer is not properly adjusted. 2. Chapter 7 Error status Probable causes #17 The machine does not stop with a new one...grammed. #19 The operation will not stop if the emergency stop switch is canceled. #21 The STEP BACK switch is pressed. 1. The programmer connector and its cable are defective...Programmer Panel circuit board BAS-311E.311EL.326E.326EL 111 Panel circuit board #22 Sewing is complete, adjust the needle stop position varies at random every time the machine operation is not resumed...
