Operating Instructions
Page 3
... pressure treated lumber, paint that may occur if sander is equipped with dust particles can occur if there is a static discharge, spark introduced in while changing an accessory. Work area should be sealed by plastic sheeting and persons not protected should be lead based,... by qualified repair personnel. Service or maintenance performed by poorly maintained tools. Use of untrained users. Safety Rules for Orbital Sanders Unplug the sander before using. Sanding particles can also cause serious lacerations. -3- Do not use only identical replacement parts. Store idle tools ...
... pressure treated lumber, paint that may occur if sander is equipped with dust particles can occur if there is a static discharge, spark introduced in while changing an accessory. Work area should be sealed by plastic sheeting and persons not protected should be lead based,... by qualified repair personnel. Service or maintenance performed by poorly maintained tools. Use of untrained users. Safety Rules for Orbital Sanders Unplug the sander before using. Sanding particles can also cause serious lacerations. -3- Do not use only identical replacement parts. Store idle tools ...
Operating Instructions
Page 6
FIG. 1 Orbital Sander VENTILATION OPENINGS CORD MICROFILTER DUST CANISTER LID SWITCH DUST PORT SHEETLOC™ FRONT CLAMP RELEASE BUTTON PAD FRONT CLAMP RELEASE TABS REAR CLAMP SPRING PLATE ... Model Number: Voltage Rating: Amperage Rating: No Load Speed: Pad Size: Regular Paper: PSA (Stick-On) Paper: 1297D 120 V 50 - 60Hz 2.0 A n0 12,000/min 4 1/2" x 4 1/8" (1/4 sheet) 4 1/2" x 5 1/2" 4 1/2" x 4 1/2" NOTE: For other tool specifications refer to the nameplate on your tool. -6- BM 2609140297 10-04 10/21/04 9:59 AM Page 6 Functional Description and...
FIG. 1 Orbital Sander VENTILATION OPENINGS CORD MICROFILTER DUST CANISTER LID SWITCH DUST PORT SHEETLOC™ FRONT CLAMP RELEASE BUTTON PAD FRONT CLAMP RELEASE TABS REAR CLAMP SPRING PLATE ... Model Number: Voltage Rating: Amperage Rating: No Load Speed: Pad Size: Regular Paper: PSA (Stick-On) Paper: 1297D 120 V 50 - 60Hz 2.0 A n0 12,000/min 4 1/2" x 4 1/8" (1/4 sheet) 4 1/2" x 5 1/2" 4 1/2" x 4 1/2" NOTE: For other tool specifications refer to the nameplate on your tool. -6- BM 2609140297 10-04 10/21/04 9:59 AM Page 6 Functional Description and...
Operating Instructions
Page 8
...of the microfilter, or remove dust with punch plate and push down on corner of PSA sheet. 2. BM 2609140297 10-04 10/21/04 9:59 AM Page 8 ATTACHING PSA "STICK-ON" ABRASIVE SHEETS Your sander can occur if there is a static discharge, spark introduced in the pores, which have ...lodged in the box, or excessive heat. WARNING Your tool is equipped with your fingers or a soft brush. Peel protective sheet from the back of lid, and remove from sander (Fig. 1). PUNCH PLATE After the paper has been installed, it will reduce dust collection efficiency. To install dust canister:...
...of the microfilter, or remove dust with punch plate and push down on corner of PSA sheet. 2. BM 2609140297 10-04 10/21/04 9:59 AM Page 8 ATTACHING PSA "STICK-ON" ABRASIVE SHEETS Your sander can occur if there is a static discharge, spark introduced in the pores, which have ...lodged in the box, or excessive heat. WARNING Your tool is equipped with your fingers or a soft brush. Peel protective sheet from the back of lid, and remove from sander (Fig. 1). PUNCH PLATE After the paper has been installed, it will reduce dust collection efficiency. To install dust canister:...
Operating Instructions
Page 9
Always hold the sander off the work when turning the switch "ON" or "OFF". The following are too...synthetic abrasives are recommended for the job. -9- Cut into four pieces of the tool. The high quality aluminum oxide sheet with heavy backing cuts faster and lasts longer. Extra Fine Grit: For final sanding bare wood and smoothing old ...TURN THE TOOL "ON" or "OFF": Push IN the switch rocker to a shop vacuum cleaner (Fig. 7). To use Bosch abrasive sheets: The uniform spacing between grains minimizes filling or loading. Natural abrasives, such as shown (Fig. 8). Choose the proper grit ...
Always hold the sander off the work when turning the switch "ON" or "OFF". The following are too...synthetic abrasives are recommended for the job. -9- Cut into four pieces of the tool. The high quality aluminum oxide sheet with heavy backing cuts faster and lasts longer. Extra Fine Grit: For final sanding bare wood and smoothing old ...TURN THE TOOL "ON" or "OFF": Push IN the switch rocker to a shop vacuum cleaner (Fig. 7). To use Bosch abrasive sheets: The uniform spacing between grains minimizes filling or loading. Natural abrasives, such as shown (Fig. 8). Choose the proper grit ...
Operating Instructions
Page 10
... more than two grit sizes. • To remove the greatest amount of stock, use . • Do not store tool with PSA sheets on page 8.) -10- STORING THE SANDER • Always latch the rear clamp lever when the tool is rough, start sanding with a coarse grit, then medium, and then finish.... Contact the work before turning the switch "OFF". Constant and excessive pressure can sand flush on the sander. BM 2609140297 10-04 10/21/04 9:59 AM Page 10 SANDING TIPS Bosch orbital sanders are overlapped as much material and uneven sanding will greatly increase the quality of your work. •...
... more than two grit sizes. • To remove the greatest amount of stock, use . • Do not store tool with PSA sheets on page 8.) -10- STORING THE SANDER • Always latch the rear clamp lever when the tool is rough, start sanding with a coarse grit, then medium, and then finish.... Contact the work before turning the switch "OFF". Constant and excessive pressure can sand flush on the sander. BM 2609140297 10-04 10/21/04 9:59 AM Page 10 SANDING TIPS Bosch orbital sanders are overlapped as much material and uneven sanding will greatly increase the quality of your work. •...