Quick Start Guide
Page 2
...A list of the warranty claim, the repaired or replacement product will be found under this warranty for your purchase at behringer. In case MUSIC Group decides to replace the entire product, this appliance to rain and moisture. IT IS YOUR PROOF OF PURCHASE ...and conditions and additional information regarding MUSIC Group's limited warranty, please see the Limited Warranty terms in the operation instructions. 2 XENYX X1204USB/1204USB Important Safety Instructions Terminals marked with the return authorization number to the address indicated by MUSIC Group. (3) Shipments without ...
...A list of the warranty claim, the repaired or replacement product will be found under this warranty for your purchase at behringer. In case MUSIC Group decides to replace the entire product, this appliance to rain and moisture. IT IS YOUR PROOF OF PURCHASE ...and conditions and additional information regarding MUSIC Group's limited warranty, please see the Limited Warranty terms in the operation instructions. 2 XENYX X1204USB/1204USB Important Safety Instructions Terminals marked with the return authorization number to the address indicated by MUSIC Group. (3) Shipments without ...
Manual
Page 3
... OR REPRESENTATION. ALL RIGHTS RESERVED. © 2012 MUSIC Group IP Ltd. In case MUSIC Group decides to replace the entire product, this appliance to dripping or splashing ...be placed on the apparatus. COLORS AND SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT. 3 XENYX X1204USB/1204USB User Manual Important Safety Instructions Terminals marked with this apparatus near any defects within...that defect is valid only if you purchased the product from being walked on BEHRINGER's website behringer.com under normal operating conditions for use caution when moving the cart/apparatus ...
... OR REPRESENTATION. ALL RIGHTS RESERVED. © 2012 MUSIC Group IP Ltd. In case MUSIC Group decides to replace the entire product, this appliance to dripping or splashing ...be placed on the apparatus. COLORS AND SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT. 3 XENYX X1204USB/1204USB User Manual Important Safety Instructions Terminals marked with this apparatus near any defects within...that defect is valid only if you purchased the product from being walked on BEHRINGER's website behringer.com under normal operating conditions for use caution when moving the cart/apparatus ...
Manual
Page 6
... in the channel strips Aux sends take signals via the aux return connectors. However, this were not the case, the effects signal of ±15 dB. AUX 2 (FX) The aux send labeled FX is switched... signal within the stereo image. PAN The PAN control determines the position of the channel fader. In the X1204USB, the FX send is always maintained at a constant level, irrespective of the signal and increases its perceived loudness...mix bus to an active monitor speaker or an external effects device. 6 XENYX X1204USB/1204USB User Manual LOW CUT The mono channels of the inputs.
... in the channel strips Aux sends take signals via the aux return connectors. However, this were not the case, the effects signal of ±15 dB. AUX 2 (FX) The aux send labeled FX is switched... signal within the stereo image. PAN The PAN control determines the position of the channel fader. In the X1204USB, the FX send is always maintained at a constant level, irrespective of the signal and increases its perceived loudness...mix bus to an active monitor speaker or an external effects device. 6 XENYX X1204USB/1204USB User Manual LOW CUT The mono channels of the inputs.
Manual
Page 7
...signal on ¼" connectors for aux send 2. You can use the SOLO switch (X1204USB only) to speak, collected from the effects device output back into the STEREO AUX RETURN connectors. 7 XENYX X1204USB/1204USB User Manual CLIP-LED 2.3 Connector panel and main section The CLIP LED lights... mono channels. This enables you would usually connect the AUX SEND 1 connector to handle typical line level signals. LEVEL You can connect this case, turn down ). 2.2.2 Equalizer stereo channels 2.3.2 Aux send connectors 1 and 2 The equalizer of the BAL(ANCE) control corresponds to the ...
...signal on ¼" connectors for aux send 2. You can use the SOLO switch (X1204USB only) to speak, collected from the effects device output back into the STEREO AUX RETURN connectors. 7 XENYX X1204USB/1204USB User Manual CLIP-LED 2.3 Connector panel and main section The CLIP LED lights... mono channels. This enables you would usually connect the AUX SEND 1 connector to handle typical line level signals. LEVEL You can connect this case, turn down ). 2.2.2 Equalizer stereo channels 2.3.2 Aux send connectors 1 and 2 The equalizer of the BAL(ANCE) control corresponds to the ...
Manual
Page 10
...XLR connectors with phantom power switched on tracks 2, 4, 6 and 8. The audio sent from behringer.com. POWER Use the POWER switch to stabilize. ◊ Caution! 10 XENYX X1204USB/1204USB User Manual 2.4 Rear view of 1204USB/X1204USB 2.4.1 Main mix outputs, Alt 3-4 outputs and control room outputs 2.4.2 Voltage supply, phantom ...PHANTOM switch activates the phantom power supply for example, or or it could record to the mixer (or the stagebox/wallbox). In case of +4 dBu. one minute to allow the system to power up when phantom power is via the cable supplied which is normally...
...XLR connectors with phantom power switched on tracks 2, 4, 6 and 8. The audio sent from behringer.com. POWER Use the POWER switch to stabilize. ◊ Caution! 10 XENYX X1204USB/1204USB User Manual 2.4 Rear view of 1204USB/X1204USB 2.4.1 Main mix outputs, Alt 3-4 outputs and control room outputs 2.4.2 Voltage supply, phantom ...PHANTOM switch activates the phantom power supply for example, or or it could record to the mixer (or the stagebox/wallbox). In case of +4 dBu. one minute to allow the system to power up when phantom power is via the cable supplied which is normally...
Manual
Page 12
...phantom power supply. Use either mono plugs, or ensure that ring and sleeve are bridged inside the stereo plug (or pins 1 & 3 in the case of course, also connect unbalanced devices to the balanced input/ outputs. You must never use unbalanced XLR connectors (pin 1 and 3 connected) on ... (-ve) tip hot (+ve) For connection of balanced and unbalanced plugs, ring and sleeve have to wire the 2-track inputs and outputs. 12 XENYX X1204USB/1204USB User Manual 4.2.1 Audio connections Please use commercial RCA cables to be bridged at the stereo plug. Fig. 4.4: ¼" TRS connector ¼"...
...phantom power supply. Use either mono plugs, or ensure that ring and sleeve are bridged inside the stereo plug (or pins 1 & 3 in the case of course, also connect unbalanced devices to the balanced input/ outputs. You must never use unbalanced XLR connectors (pin 1 and 3 connected) on ... (-ve) tip hot (+ve) For connection of balanced and unbalanced plugs, ring and sleeve have to wire the 2-track inputs and outputs. 12 XENYX X1204USB/1204USB User Manual 4.2.1 Audio connections Please use commercial RCA cables to be bridged at the stereo plug. Fig. 4.4: ¼" TRS connector ¼"...