Operation Guide
Page 2
... kits often include low-level RCA cables, extra large power and ground wires, a fuse or circuit breaker and connector for adding other amps LXA300 • 150 watts RMS bridged into a 4 ohm load • Bridgeable design to direct full power to 10 watts at maximum ...or upside down configuration. Professional Tip Amplifier Installation Kit Your installation job will need before making any cuts or connections. ® Features The Jensen LXA300 power amplifier is best to protect the amplifier from short circuit, DC offset and thermal overload • Unique, super-efficient heat sink ...
... kits often include low-level RCA cables, extra large power and ground wires, a fuse or circuit breaker and connector for adding other amps LXA300 • 150 watts RMS bridged into a 4 ohm load • Bridgeable design to direct full power to 10 watts at maximum ...or upside down configuration. Professional Tip Amplifier Installation Kit Your installation job will need before making any cuts or connections. ® Features The Jensen LXA300 power amplifier is best to protect the amplifier from short circuit, DC offset and thermal overload • Unique, super-efficient heat sink ...
Operation Guide
Page 6
On the amp, slowly turn the volume up slowly until you just start to hear distortion and back it in Tri-mode. LPF Use LPF and HPF to ... CD (make sure the input level control on the amp is turned down just a bit. Now back the volume down all the way (counterclockwise or all tones go to run a subwoofer and two full- LXA300 Crossover (X-OVER) Adjust the crossover to accommodate your Jensen amplifier 50 250 to speakers. Use with woofers or...
On the amp, slowly turn the volume up slowly until you just start to hear distortion and back it in Tri-mode. LPF Use LPF and HPF to ... CD (make sure the input level control on the amp is turned down just a bit. Now back the volume down all the way (counterclockwise or all tones go to run a subwoofer and two full- LXA300 Crossover (X-OVER) Adjust the crossover to accommodate your Jensen amplifier 50 250 to speakers. Use with woofers or...
Operation Guide
Page 11
... to keep the amp cool, especially if you are driving subwoofers with the amp) Check speakers and... No power to pages 5, 6 and 7 for amp to work Radio volume is too sensitive Sound from only...noise) Loud pop in your speakers. ® LXA300 Troubleshooting Problem Amplifier does not operate (power LED ...You may have more than 2 ohms per channel Amp will not operate into 2 ohms bridged Refer to ...radio is not uncommon. Let amp cool down before attempting to turn the amp on Fuse blown Input level... Remote wire (blue) not properly connected Amp is in thermal protection Faulty speaker connection ...
... to keep the amp cool, especially if you are driving subwoofers with the amp) Check speakers and... No power to pages 5, 6 and 7 for amp to work Radio volume is too sensitive Sound from only...noise) Loud pop in your speakers. ® LXA300 Troubleshooting Problem Amplifier does not operate (power LED ...You may have more than 2 ohms per channel Amp will not operate into 2 ohms bridged Refer to ...radio is not uncommon. Let amp cool down before attempting to turn the amp on Fuse blown Input level... Remote wire (blue) not properly connected Amp is in thermal protection Faulty speaker connection ...
Operation Guide
Page 12
...: damage resulting from state to state and province to repair the product, but Jensen will service or arrange for the removal and/or installation of Recoton Audio Corporation ...Crossover Frequencies Low/High: 50-250 Hz Power Requirement 14.4 VDC (10.8-15.6 VDC allowable) Fuse Requirements 30 amp blade-type fuse Dimensions 2.25" x 11.125" x 8" (56.5mm x 282mm x 203mm) Specifications subject...the repair or replacement, at 1-800-323-4815. The product should be in this warranty. Specifications LXA300 Amplifier Power output @ 14.4 VDC, 20-20 kHz 4 ohms) 75 Watts per channel RMS,...
...: damage resulting from state to state and province to repair the product, but Jensen will service or arrange for the removal and/or installation of Recoton Audio Corporation ...Crossover Frequencies Low/High: 50-250 Hz Power Requirement 14.4 VDC (10.8-15.6 VDC allowable) Fuse Requirements 30 amp blade-type fuse Dimensions 2.25" x 11.125" x 8" (56.5mm x 282mm x 203mm) Specifications subject...the repair or replacement, at 1-800-323-4815. The product should be in this warranty. Specifications LXA300 Amplifier Power output @ 14.4 VDC, 20-20 kHz 4 ohms) 75 Watts per channel RMS,...