User Guide
Page 3
... tweeter Sensitivity 88 dB SPL (2.83 V / 1 m) Maximum Output 108 dB SPL (continuous), 114 dB SPL (peak) Power Rating 100 W (RMS), 200 W (peak) Recommended Amplifier Power 50 W - 150 W (RMS) Input Impedance 4 Ω (nominal) Polarity Positive signal at + input produces outward LF...the latest information about this product (system requirements, compatibility information, etc.) and product registration, visit alesis.com/elevate-6-passive. User Guide (English) Introduction Box Contents Elevate 6 Passive; Frequency 50 100 200 500 1K 3 (Hz) 2K 5K 10K 20K Specifications subject...
... tweeter Sensitivity 88 dB SPL (2.83 V / 1 m) Maximum Output 108 dB SPL (continuous), 114 dB SPL (peak) Power Rating 100 W (RMS), 200 W (peak) Recommended Amplifier Power 50 W - 150 W (RMS) Input Impedance 4 Ω (nominal) Polarity Positive signal at + input produces outward LF...the latest information about this product (system requirements, compatibility information, etc.) and product registration, visit alesis.com/elevate-6-passive. User Guide (English) Introduction Box Contents Elevate 6 Passive; Frequency 50 100 200 500 1K 3 (Hz) 2K 5K 10K 20K Specifications subject...
User Guide
Page 5
...studio size, shape, and acoustical treatment: Elevate 6 Passive monitors are set to their default settings will sound as flat and accurate as low-frequency "sound reflectors" for your connector type: Important: We recommend using a powered amplifier that can cause the monitors to...the binding posts are designed to have a flat frequency response, you hear at the "mixing position." Acoustic Compensation Since studio monitors (including the Elevate 6 Passive) are tightened completely. (2) Insert the banana connectors into 4 Ω. 1/4" (6.35 mm) TS Speaker Cable: Connect the amplifier...
...studio size, shape, and acoustical treatment: Elevate 6 Passive monitors are set to their default settings will sound as flat and accurate as low-frequency "sound reflectors" for your connector type: Important: We recommend using a powered amplifier that can cause the monitors to...the binding posts are designed to have a flat frequency response, you hear at the "mixing position." Acoustic Compensation Since studio monitors (including the Elevate 6 Passive) are tightened completely. (2) Insert the banana connectors into 4 Ω. 1/4" (6.35 mm) TS Speaker Cable: Connect the amplifier...
User Guide
Page 6
...8486;. • the 1/4" (6.35mm) TRS input, using a standard 1/4" 2 (6.35mm) TRS cable • the two binding posts, using two Elevate 6 Passive monitors, make sure the HF Trim switch is boosted or attenuated. This setting compensates for a studio that can use bare wires or banana...with this switch, begin by 2 dB. If your amplifier's positive terminal. Tips: When using the binding posts, we recommend using a powered amplifier that sounds too "dead" (not enough high-frequency reflection around the room). Bass Reflex Port: These ports discharge very-low- Features ...
...8486;. • the 1/4" (6.35mm) TRS input, using a standard 1/4" 2 (6.35mm) TRS cable • the two binding posts, using two Elevate 6 Passive monitors, make sure the HF Trim switch is boosted or attenuated. This setting compensates for a studio that can use bare wires or banana...with this switch, begin by 2 dB. If your amplifier's positive terminal. Tips: When using the binding posts, we recommend using a powered amplifier that sounds too "dead" (not enough high-frequency reflection around the room). Bass Reflex Port: These ports discharge very-low- Features ...