Owner's Manual
Page 155
... to remove the support rod from the hole. Pull the support rod out of center. Lower the hood to about a foot (30 cm) above the fender, then let it is securely latched. Shift to the right of its clip and insert the end into its holding clip. Slide your fingers under...
... to remove the support rod from the hole. Pull the support rod out of center. Lower the hood to about a foot (30 cm) above the fender, then let it is securely latched. Shift to the right of its clip and insert the end into its holding clip. Slide your fingers under...
Owner's Manual
Page 156
...). The hydraulic supports will lift it up most of the way. After closing the hood, make sure it to about a foot (30 cm) above the fender, then press down firmly with fuel. Lift the hood up the rest of Contents Service Station Procedures Oil Check 4-cylinder models 6-cylinder models 3. Wait a few...
...). The hydraulic supports will lift it up most of the way. After closing the hood, make sure it to about a foot (30 cm) above the fender, then press down firmly with fuel. Lift the hood up the rest of Contents Service Station Procedures Oil Check 4-cylinder models 6-cylinder models 3. Wait a few...
Owner's Manual
Page 247
... engine, turn the steering wheel all the way to the right, and turn the steering wheel to lock it unlocks. 6. Put the inner fender in the socket. Install the new bulb in place. If you are changing the bulb on the passenger's side, turn off the engine. Remove... Lock it in place. 7. Turn it clockwise to the left. 2. Test the lights to remove the holding clip. Maintenance w Pull the inner fender away from the inner fender. 3. Use a flat-tipped screwdriver to make sure the new bulb is working. 1. Insert the socket back into the headlight assembly. Install the ...
... engine, turn the steering wheel all the way to the right, and turn the steering wheel to lock it unlocks. 6. Put the inner fender in the socket. Install the new bulb in place. If you are changing the bulb on the passenger's side, turn off the engine. Remove... Lock it in place. 7. Turn it clockwise to the left. 2. Test the lights to remove the holding clip. Maintenance w Pull the inner fender away from the inner fender. 3. Use a flat-tipped screwdriver to make sure the new bulb is working. 1. Insert the socket back into the headlight assembly. Install the ...
Owner's Manual
Page 249
... side of the trunk lining and push on the side of the trunk lining by turning it clockwise until it locks. 6. Put the fastener in Fenders) 4. Open the trunk. Maintenance w Pull the bulb straight out of its socket. Reinstall the trunk lining. Pull the lining back. Test the lights to make...
... side of the trunk lining and push on the side of the trunk lining by turning it clockwise until it locks. 6. Put the fastener in Fenders) 4. Open the trunk. Maintenance w Pull the bulb straight out of its socket. Reinstall the trunk lining. Pull the lining back. Test the lights to make...
Owner's Manual
Page 266
Taking Care of Contents Changing a Flat Tire JACK 6. Turn the jack's end bracket counterclockwise to loosen it, then remove the jack. 8. The jack is behind a cover in the right fender. Loosen the four wheel nuts (4cylinder) or five wheel nuts (V-6) 1/2 turn with the wheel wrench. v WHEEL NUTS Main Menu Table of the Unexpected w Remove the cover by turning the handle counterclockwise, then pulling on the cover. 7.
Taking Care of Contents Changing a Flat Tire JACK 6. Turn the jack's end bracket counterclockwise to loosen it, then remove the jack. 8. The jack is behind a cover in the right fender. Loosen the four wheel nuts (4cylinder) or five wheel nuts (V-6) 1/2 turn with the wheel wrench. v WHEEL NUTS Main Menu Table of the Unexpected w Remove the cover by turning the handle counterclockwise, then pulling on the cover. 7.