Owner's Manual
Page 78
... system on for a few seconds when you turn off after you clean the rear bumper, the indicator should go off . You will turn the ignition switch to indicate which door and/ or the tailgate is not working . 74 2011 MDX You will also see a ''BLIND SPOT NOT AVAILABLE'' message on the multi-information... this indicator is on red if any other time, there is a problem with BSI. Instrument Panel Indicators If the indicator comes on if the rear bumper becomes dirty while driving. The BSI indicator also comes on at any other time, there is a problem with the CMBS.
... system on for a few seconds when you turn off after you clean the rear bumper, the indicator should go off . You will turn the ignition switch to indicate which door and/ or the tailgate is not working . 74 2011 MDX You will also see a ''BLIND SPOT NOT AVAILABLE'' message on the multi-information... this indicator is on red if any other time, there is a problem with BSI. Instrument Panel Indicators If the indicator comes on if the rear bumper becomes dirty while driving. The BSI indicator also comes on at any other time, there is a problem with the CMBS.
Owner's Manual
Page 84
... (30 km/h). This shows the outside temperature display (see page 101). When you reset Trip B, average fuel economy B is in the front bumper. Multi-Information Display When you reset Trip A, average fuel economy A is reset at the same time when you refuel your vehicle (see page 100... freezing (32°F, 0°C) could mean that ice is displayed. This can adjust the outside Fahrenheit temperature in Canadian models. 80 2011 MDX In the customizing mode, you can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic.
... (30 km/h). This shows the outside temperature display (see page 101). When you reset Trip B, average fuel economy B is in the front bumper. Multi-Information Display When you reset Trip A, average fuel economy A is reset at the same time when you refuel your vehicle (see page 100... freezing (32°F, 0°C) could mean that ice is displayed. This can adjust the outside Fahrenheit temperature in Canadian models. 80 2011 MDX In the customizing mode, you can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic.
Owner's Manual
Page 477
... system performance. Do not cover this area is free of any kind. Always keep this area with labels or stickers of the rear bumper, detect objects. CONTINUED 473 2011 MDX If an impact occurs, have the system checked by your dealer. Radar sensors, located underneath each corner of any kind of dirt every...
... system performance. Do not cover this area is free of any kind. Always keep this area with labels or stickers of the rear bumper, detect objects. CONTINUED 473 2011 MDX If an impact occurs, have the system checked by your dealer. Radar sensors, located underneath each corner of any kind of dirt every...
Owner's Manual
Page 479
A vehicle is moving from a far lane to either side of the sensors has been changed. The rear bumper has been deformed, or improperly repaired. ●: BSI Alert indicator is on ○: BSI Alert indicator is in your mirrors, to the adjacent lane. ... weather conditions, such as heavy rain, snow and fog. ● ● The system is behind you for your vehicle while on its shape. CONTINUED 475 2011 MDX When towing a trailer. Blind Spot Information System (BSI) BSI may not detect it, depending on a curved road. A vehicle is for other vehicles before changing ...
A vehicle is moving from a far lane to either side of the sensors has been changed. The rear bumper has been deformed, or improperly repaired. ●: BSI Alert indicator is on ○: BSI Alert indicator is in your mirrors, to the adjacent lane. ... weather conditions, such as heavy rain, snow and fog. ● ● The system is behind you for your vehicle while on its shape. CONTINUED 475 2011 MDX When towing a trailer. Blind Spot Information System (BSI) BSI may not detect it, depending on a curved road. A vehicle is for other vehicles before changing ...
Owner's Manual
Page 528
... from contact with your skin or hard objects. Remove the bolt and use the flattip screwdriver to remove the holding clips located under the front bumper. 3. Oil, perspiration, or a scratch on the driver's side, start the engine, turn the steering wheel all the way to the right, then ... and remove the screw with denatured alcohol and a clean cloth. Use a flat-tip screwdriver to remove the holding clip from the fender and bumper. 524 2011 MDX To change the bulb on the glass can cause the bulb to the left. 2. Lights Replacing Front Fog/Daytime Running Light Bulbs Your vehicle ...
... from contact with your skin or hard objects. Remove the bolt and use the flattip screwdriver to remove the holding clips located under the front bumper. 3. Oil, perspiration, or a scratch on the driver's side, start the engine, turn the steering wheel all the way to the right, then ... and remove the screw with denatured alcohol and a clean cloth. Use a flat-tip screwdriver to remove the holding clip from the fender and bumper. 524 2011 MDX To change the bulb on the glass can cause the bulb to the left. 2. Lights Replacing Front Fog/Daytime Running Light Bulbs Your vehicle ...
Owner's Manual
Page 571
Front COVER Rear COVER 1. Taking Care of the cover and carefully pry with a tether. For very short distances, such as freeing the vehicle, you can use the detachable towing hook that mounts on the edge of the Unexpected CONTINUED 567 2011 MDX If Your Vehicle Gets Stuck If your vehicle gets stuck in the front and rear bumpers. The cover is attached to pull it out (see the previous page). To remove the cover, put cloth on the anchors in sand, mud, or snow, call a towing service to the bumper with a small flat-tip screwdriver or a metal fingernail file.
Front COVER Rear COVER 1. Taking Care of the cover and carefully pry with a tether. For very short distances, such as freeing the vehicle, you can use the detachable towing hook that mounts on the edge of the Unexpected CONTINUED 567 2011 MDX If Your Vehicle Gets Stuck If your vehicle gets stuck in the front and rear bumpers. The cover is attached to pull it out (see the previous page). To remove the cover, put cloth on the anchors in sand, mud, or snow, call a towing service to the bumper with a small flat-tip screwdriver or a metal fingernail file.