Zenith SL-5798-WH-A Support Question
Zenith SL-5798-WH-A Support Question
Find answers below for this question about Zenith SL-5798-WH-A - Heath - 270-Degree Triple Head Halogen Motion Sensing Security Light.Need a Zenith SL-5798-WH-A manual? We have 1 online manual for this item!
Question posted by Fishhooker2001 on December 18th, 2014
Motion Light Won't Turn On Unless It Is In Test Setting..
The person who posted this question about this Zenith product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by TommyKervz on December 19th, 2014 12:59 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,843
Member since:
January 10th, 2013 Points: 17,776,843
Please refer to the mnaual below
Please click here for further assistance
Related Zenith SL-5798-WH-A Manual Pages
User Guide - Page 1
... the ON-TIME switch in wet locations. to Dawn
x
* resets to Dawn
LAMP MODE
Sensor Light Control
3 Wire Connectors
Put the LAMP MODE switch in the Normal, Soft, or Flash position.
DualBrite® Triple Halogen Motion Sensing Light
Model 5798
Features
• Turns on lighting when motion is intended for use with the enclosed
gasket and with a junction box marked for...
User Guide - Page 2
... with the ON-TIME switch in this feature. NOTE: If fixture is sensed, the light turns on full bright for proper under eave installation, the sensor head must be in the next two steps for one second then back on effects) available when motion is no longer detected and after dusk (Off, 3 hr., 6 hr., until dawn...
User Guide - Page 3
... fixture cool. ❒ To remove lamp shade, loosen set screw 2 full
turns with a small flat-head screwdriver.Turn shade counterclockwise and remove. ❒ To remove bulb, pull... the set screws
wires as shown.
from the sensor. Push the small gasket hole over the Mounting Screw. Secure the fixture to hold the fixture while wiring.
Wire the Light Control
Mount the Light Control
...
User Guide - Page 4
... traffic may trigger the control.
• Nearby large, light-colored objects reflecting light may
increase false triggering. ❒ Secure the sensor head by
tightening the clamp screw. The detector is detected (1, 5, or 20 minutes).
❒ Set the DualBrite® switch to 100 Watt Maximum each lamp holder].
TEST, AUTO and MANUAL MODE Lamp Modes Normal, Soft, Flash...
User Guide - Page 5
... brightly-painted heat-reflective surface. (Reposition sensor. Sensor is positioned too close to -Dawn setting
1. Heat or light from other objects may be sensing small animals or automobile traffic (re-aim sensor). 2. Light control is in the Test mode and warming up flashing is normal in this is turned off in Manual Mode. Light control is in Flash mode. (An...
User Guide - Page 6
... PROFITS, WHETHER OR NOT FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of purchase, any obligation to misuse, abuse or negligence, light bulbs, batteries, and other rights which gives you .
Please keep your dated sales receipt, it is not extended to province. Repair service, adjustment and calibration...
Similar Questions
Motion Sensor
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
Hi. Just bought a 10 year old house with Heath sensor on the back porch. I turn on the light and it ...
(Posted by Barry95996 9 years ago)
Motion Sensor Light Won't Turn Off
(Posted by ungm3lm4 9 years ago)
How To Wire Health Motion Sensor Sl-5410a
(Posted by ranyog 9 years ago)
Zenith Motion Sensor Light Won't Turn Off
(Posted by matrijone 9 years ago)
Just Had The Zenith Sl 5798 Installed & The Motion Sensor Does Not Seem To Work
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
(Posted by Peyton 11 years ago)