Zenith SL-4133-OR Support Question
Zenith SL-4133-OR Support Question
Find answers below for this question about Zenith SL-4133-OR - Heath - Shaker Cove Mission Style 150-Degree Motion Sensing Decorative Security Light.Need a Zenith SL-4133-OR manual? We have 1 online manual for this item!
Question posted by horse44 on October 11th, 2012
Manual Position On This Model
Where is the "Manual Position" on this model???
Mine has "Test, 1,5,10 Min.
I want the unit to function as Dusk to Dawn.
It it at the "Min" position??
Current Answers
Answer #1: Posted by quaff on October 12th, 2012 12:14 PM
quaff
Member since:
November 13th, 2011 Points: 537,590
Member since:
November 13th, 2011 Points: 537,590
Check out page one of this manual: http://www.manualowl.com/m/Zenith/SL-4133-OR/Manual/272105 ; it explains what manual mode is, how to activate it, and the limitations of it. I hope that this helps!
Related Zenith SL-4133-OR Manual Pages
User Guide - Page 1
...
Mode: Test Auto Manual
On-Time Works: Day
5 Seconds
x
1, 5, or 10 Min
To Dawn*
Night x x x
* resets to Auto Mode at night because daylight returns the sensor to toggle 1 Second between AUTO and MANUAL OFF then... back on to AUTO.
Tail Assembly (Lantern & Coach)*
Before installation, record the model number from back of possible warranty issues. MODE.
Motion Sensing Coach Lights...
User Guide - Page 2
...mounting plate over.
595-5530-13 WARNING: Turn power off at 1, 5,
or 10 minutes
AUTO
Flip light switch
MANUAL MODE
off for one second then back on*
* If you get confused while switching modes..., turn the power off for additional information). 3.
Mode Switching Summary
TEST
...
User Guide - Page 3
...
Light Fixture
Light Fixture
Two Motion Lights
❒ Twist the junction box wires and the fixture wires together as shown. CAUTION: DO NOT connect the RED wire unless you want to... "pigtail" with the National Electrical Code through .
5. Secure the other lights from the motion sensor.
Black
Green or Bare
White One Motion Light
Light Fixture
595-5530-13
Black to black White to...
User Guide - Page 4
... up. Once you have selected the fixtures to control another motion sensing light fixture (Master / Slave): Strip the red wire in the...For instance, if you have 3 fixtures rated 100 Watts, 150 Watts, and 75 Watts respectively, you have a total load ...of additional lighting load can destroy both light fixtures. When wiring to control a standard light fixture: Strip the motion sensor's red wire...
User Guide - Page 5
... proper bulb type and wattage.
❒ If so equipped, install the fixture top.Secure with silicone weather sealant.
❒ Install light bulb. Optional Assembly
❒ If so equipped, you will not be installing the optional tail assembly, install the decorative nut onto the bottom of the fixture now.
Hex nut
1. Screw in extension...
User Guide - Page 6
... noting where you want the light to stay on .
TESTING
❒ Turn on wait 1 1/2 minutes.
❒ Set SENSITIVITY to mid position and ON-TIME to TEST position.
M - Note: Grasp the sensor only as shown and turn on after motion is less sensitive to motion directly towards it will detect motion.
Do not force it past the stops.
150°
6 ft. (1.8 m)
30...
User Guide - Page 7
TEST, AUTO, and MANUAL MODE Time Delay 1, 5, 10 minutes
HeathCo LLC reserves the right to discontinue products and to change specifications at any time without incurring any obligation to 150° Electrical Load. . . . . . Light control is set too high. (Reduce sensitivity.)
SYMPTOM Light stays on and off . 2. Upto500Watts(4.1A.)
Maximum Tungsten Incandescent Power Requirements 120...
User Guide - Page 8
...damages, so the above limitation or exclusion may also have the following information available: Model Number, Date of Purchase, and Place of purchase, any furnished component will be ... extended to misuse, abuse or negligence, light bulbs, batteries, and other equipment and components that a customer uses in its entirety. You may also want to you experience a problem, follow this...
Similar Questions
How To Deactivate The Motion Sensor On The Heath/zenith Sl-5610-wh-b?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
How to deactivate the motion sensor on the Heath/Zenith SL-5610-WH-B?
(Posted by emvilla 4 years ago)
Motion Light Won't Turn On Unless It Is In Test Setting..
(Posted by Fishhooker2001 9 years ago)
Heath Zenith Motion Sensor Light Wont Turn Off
(Posted by Tiighchairu 10 years ago)
Just Had The Zenith Sl 5798 Installed & The Motion Sensor Does Not Seem To Work
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
We had an electrician install the Zentih SL 5798 on our deck facing out into the field. The motion s...
(Posted by Peyton 11 years ago)
