Whirlpool WTW4850XQ Support Question
Whirlpool WTW4850XQ Support Question
Find answers below for this question about Whirlpool WTW4850XQ.Need a Whirlpool WTW4850XQ manual? We have 5 online manuals for this item!
Question posted by arnieccyar on June 27th, 2014
Is The Whirlpool Washer Wtw4850xq Direct Drive
The person who posted this question about this Whirlpool product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Whirlpool WTW4850XQ Manual Pages
Installation Instructions - Page 2
...
Select proper location for installation are in cardboard insert in a basement, laundry room, closet, or recessed area.
271/2"
27"
(648 mm) (686...to 19⁄16" (39.5 mm)
Optional tools:
Flashlight
Bucket
Parts supplied:
NOTE: All parts supplied for your washer in the top of your Use and Care Guide. n 8212656RP n 8212641RP n 8212646RP n 8212545RP
n 8212487RP n 8212638RP
...
Installation Instructions - Page 3
... spacing of 1" (25 mm) on the sides. Minimum siphon break: 28" (710 mm) from bottom of 1" (25 mm) under entire washer. Top of laundry tub must support washer's total weight (with maximum slope of washer. (Additional hoses may be inside standpipe or below 32° F (0° C).
n A grounded electrical outlet located within 3 ft (0.9 m) of hot...
Installation Instructions - Page 4
... a gas pipe. It is necessary for proper operation and to avoid excessive noise from shipping carton on cardboard supports.
NOTE: To avoid floor damage, set washer onto cardboard before moving it at this appliance be provided. n Check with a power supply cord having a 3 prong grounding plug. n Do not ground to install it...
Installation Instructions - Page 5
...laundry tub. IMPORTANT: 4.5" (113 mm) of drain hose should be used.
5 NOTE: Keep tray in place on bottom of drain hose, slide it over side of drain hose onto black drain port and secure with separate directions. You may need to drain port
Remove tape from washer...parts with clamp. Attach drain hose to move washer later.
4. For a laundry tub or standpipe drain, go to remove all ...
Installation Instructions - Page 6
... cuts, wear, or leaks are only connecting to hot water inlet valve marked with separate directions. It will cross over each other when attached correctly. See "Tools and Parts". Water ...a few seconds through hoses into a laundry tub, drainpipe, or bucket to water faucets with new inlet hoses with flat washers (not provided). Connect Inlet Hoses
Washer must be connected to prevent clogs....
Installation Instructions - Page 7
...edges of front using lid, as shown. Use side seam as needed. If washer is level, use a 9/16" or 14 mm open -end or adjustable...washer in its final location, place a level on feet until they are about 4" (102 mm) with wooden block. Check levelness of washer.
15. 12. Secure drain hose
Laundry Tub
Standpipe
Wall
14. Check levelness of washer. When washer is level, skip to laundry...
Installation Instructions - Page 8
...powdered or liquid detergent and pour it into washer basket or detergent dispenser (on some models). Start washer and allow to see what was skipped. q Check that washer is an extra part, go back through... Check that you have all of /recycle all parts are on washer.
q Dispose of your tools. q Check that all packaging materials.
Close lid.
16. Plug into a grounded 3...
Dimension Guide - Page 1
...phone numbers in your Use and Care Guide. Top-Loading Washer
PRODUCT MODEL NUMBERS WTW4900X, WTW5500X, WTW5550X, WTW5600X, WTW5640X,...circuit breaker is required. Top of wash tub. Because Whirlpool Corporation policy includes a continuous commitment to improve our ...siphon break: 28" (710 mm) from bottom of laundry tub must be provided. Specifications subject to change without...
Energy Guide - Page 1
... this label before consumer purchase.
Government
Federal law prohibits removal of
$1.218 per therm.
• For more information, visit www.ftc.gov/appliances (P/N W10062936) Clothes Washer Capacity: Standard
Whirlpool Corporation Model: WTW4850X* Cat. U.S.
Warranty Information - Page 1
... the finish of your complete model number and serial number. You can be found by checking the "Assistance or Service" section or by a Whirlpool designated service company. WHIRLPOOL CORPORATION LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached...
Use & Care Guide - Page 3
...laundry, fill it is normal for the best performance. no water level selector is added. Using regular detergent will likely result in the "Cycle Status Lights" section. Use only High Efficiency (HE) detergent. When loading the washer...The second stage adds the correct amount of the wash cycle delivers detergent directly to thoroughly wet the load.
The lower water level combined with a...
Use & Care Guide - Page 4
... load and you may also come on your laundry load. At each stage of these spins. The sensing process will then move the load briefly, pause to allow water to the load, and resume adding water. It ensures that are available on , then washer is added to select available cycles on during...
Use & Care Guide - Page 5
...will turn on.
LID LOCKED To allow for best results. Concentrated cleaning delivers the detergent directly to resume the cycle. DONE
Once the cycle is normal to have the sensing light on ... sounds may take several second pause. For cycles that the lid is restarted.
5 SPIN
The washer spins the load at different stages in the wash cycle. Press START/Pause/Unlock again to the...
Use & Care Guide - Page 7
...NOTE: Always read and follow fabric care label instructions to avoid damage to items during washing. USING YOUR WASHER
1.
Loose change, buttons, or any small object can pass under the agitator and become trapped, causing ... and tears to avoid further damage to your laundry
2. If using an Oxi or color-safe bleach laundry boost product, add to the bottom of detergent to avoid pilling.
Use & Care Guide - Page 8
... bleach or Oxi products in loose heaps evenly around the agitator; always follow manufacturer's directions for best cleaning and to choose your load size. Then select Fabric Softener Added-Yes...See max fill line arrows.
Select cycle
IMPORTANT: Do not tightly pack or force items into washer
5. Add liquid chlorine bleach
to dispenser
Turn cycle knob to reduce wrinkling and tangling.
4. ...
Use & Care Guide - Page 11
...shipping materials back inside washer basket.
6. REINSTALLING/USING WASHER AGAIN
To reinstall washer after non-use washer again:
1. Use half the manufacturer's recommended amount of washer. Flush water pipes and hoses. Turn on both water faucets. TRANSPORTING YOUR WASHER
1. If washer will be moved during freezing weather, follow Winter Storage Care directions before moving :
1. Close...
Use & Care Guide - Page 12
..., go to www.whirlpool.com/help -
Fill hose washers.
Washer not performing as coins could be in washer drain system. It is on (indicating that the washer was unable to fill... to be level.
Washer won't run or fill, washer stops working or wash light remains on .
If flooring is added to the washer. Wash smaller loads to drainpipe or laundry tub.
Empty pockets ...
Use & Care Guide - Page 13
... the Drain & Spin cycle to slow or stop the washer. In Canada www.whirlpool.ca
If you experience
Possible Causes
Solution
Washer not performing as expected (cont.)
Washer won't run . Do not interrupt cycle.
Always measure and follow detergent directions based on (indicating that the washer was unable to pump out water within 10 minutes)
Empty...
Use & Care Guide - Page 14
... the load items.
14 http://www.whirlpool.com/help -
Load not rinsed
Energy-saving controlled wash temperatures. Remove any kinks in loose heaps evenly around the basket wall. Load is normal.
This includes cooler hot and warm washes. Always measure detergent and follow detergent directions based on washer may require additional rinsing. TROUBLESHOOTING...
Use & Care Guide - Page 15
...packed. Use cycle designed for fabric type. Always read and follow the manufacturer's directions.
Always follow garment manufacturer's care label instructions. The suds from regular detergent can... button. Be sure to improve cleaning. In Canada www.whirlpool.ca
If you experience
Possible Causes
Solution
Washer not performing as expected (cont.)
Not cleaning or removing stains...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Vibration - Front-load washer
...shipping bolts must be in high-speed spin Some noise during drain - Vibration - adjust the feet if the washer teeters. The lock nuts on the optional pedestal? Failure to remove all four feet should be securely placed ...;should be removed from corner to : Find Manuals & Is the washer placed directly on the floor and not on all four shipping bolts removed? Front-load... -
Detergent is on the load - Front-load washer
... temperature colder than 60°F (15.5°C)? Laundry detergents are not enough suds - Powdered detergent may not dissolve well in the washer may need to clean well at temperatures above 60...less detergent. If too much detergent? Detergent remains in the washer, following the detergent manufacturer's directions. If you have very soft water or a very lightly soiled load,... -
Lint is on the load - Top-load HE washer with Dispensers in Corners
.... Always check all pockets and the interior of the washer prior to starting a new load of laundry? Cycles such as low-twist terry cloth towels..., will produce more lint in Corners Damaged clothing - Load should move freely. Follow the detergent manufacturer's directions. Lint is tightly packed. Top-load washer...
Similar Questions
Direct Drive
is this unit direct drive.I really like them better than belt
is this unit direct drive.I really like them better than belt
(Posted by gamtnhillbilly 7 years ago)
Whirlpool Wtw8600yw Is Driven By A Direct Drive Motor. What About Wtw7300xw?
(Posted by Anonymous-72754 11 years ago)