Home » Whirlpool » Laundry Washers » Whirlpool WFW70HEBW

Whirlpool WFW70HEBW Support Question

Find answers below for this question about Whirlpool WFW70HEBW.
Need a Whirlpool WFW70HEBW manual? We have 5 online manuals for this item!

Whirlpool Overview Questions Manuals Reviews Videos Research

Question posted by 56pflagg57 on June 28th, 2017

Washing Machine Makes Noise But No Display

my whirlpool front load washer stopped working in the door locked position it was making a noise but no display n the front paneI. I removed the top of the machine and manually released the latch, i have replaced the latch but if I plug in the power the same situation occurs, I have running noise and no display on the front panel.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Odin on June 28th, 2017 2:12 PM

This answer was accepted by the poster of the original question.

Odin

Member since:
April 10th, 2010

Points: 41,236,640

1,100
points

You'll probably find the detailed rundown at http://bit.ly/2tqcsAb more helpful.

Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.

Answer #2: Posted by waelsaidani1 on June 28th, 2017 2:02 PM

waelsaidani1

Member since:
May 12th, 2013

Points: 19,501,787

100
points

Main reasons(either front or top load):
1. Power breaker off, washer not plugged in.
2. Lid switch faulty, door switch faulty.
3. Start switch and or timer faulty.
4. Washer motor faulty.
5. Main control board faulty or shorted.

Related Whirlpool WFW70HEBW Manual Pages

Installation Guide - Page 3

...level floor with foam backing is not recommended. n Floor must be large enough to allow door to reduce noise transfer. Recessed area or closet installation (stacked washer and dryer): 6" (152 mm) 3" (76 mm) 76.5" (1943 mm) 48 ...and load) of 20-100 psi (137.9-689.6 kPa). IMPORTANT: Do not install, store or operate washer where it will need: n A water heater set to weather or in door are ...

Installation Guide - Page 4

...96" (2.44 m) from bottom of washer. Floor drain system 4.5" (114 mm) See requirements for a standpipe drain: 2" (51 mm). Top of laundry tub must be purchased separately. Wall standpipe...See "Alternate Parts". Select method you have an overhead sewer and need . Recessed area or closet installation (washer only): Custom cabinet installation: 3" (76 mm) 48 in.2 (310 cm2) 7" (178 mm) 14...

Installation Guide - Page 7

...a laundry tub, drainpipe, or bucket to work properly. Do not use hoses without washers. ...laundry tub. do not force excess hose into standpipe (shown in standpipe Drain hose form A. Use pliers to remove the drain hose form from the end of which hose is seated on valve when attaching to water faucets with new inlet hoses with separate directions. Coupling B. HELPFUL TIP: Make...

Installation Guide - Page 8

... . Record hose installation or replacement dates for leaks Remove cardboard from side to Step 19. Not Level LEVEL Not Level 17. If washer rocks, go to side. Place a level on valve when attaching to washer LEVEL WASHER Leveling your washer properly reduces excess noise and vibration. 16. Repeat, rocking washer from beneath washer. Check levelness of washer, checking each side...

Use & Care Guide - Page 5

...displayed (for times longer than 99 minutes, hours will lock while the TumbleFresh™ option is preset for information on the cycle selected. Factors such as load size, wash temperature, and water pressure may cause the washer...main wash cycle. NOTE: The door will be changed. • Faster spin speeds mean shorter dry times, but will periodically tumble the load after the wash cycle....

Use & Care Guide - Page 6

... will likely result in low position Powdered detergent: Lift the selector to the load. Cycle Status Lights USING THE DISPENSER DRAWER 1. Open the dispenser drawer. 2. Door Locked Door Locked will unlock briefly before the wash begins. 6 You will hear a click, the drum will make a partial turn, and the door will light to dispenser Delay Wash Model WFW80HE shown If a Delay...

Use & Care Guide - Page 7

... Normal Extra Rinse and mixed loads Off Light Delay Wash This cycle uses a concentrated detergent solution along with affresh® washer cleaner tablet or liquid chlorine bleach to remove excess water from the load. There is complete. Medium load: Fill the washer drum up to add water. Extra-large load: Fill the washer drum, but make sure clothes can be...

Use & Care Guide - Page 8

... manufacturer's instructions. 3. n Wash small items in the washer. n Depending on an inside out to your laundry Single-dose laundry packet, Oxi-type boosters, color-safe bleach, or fabric softener crystals can set stains into washer Sort items by pushing it without laundry Before washing clothes for a medium-size load. Load laundry into fabric. Washer door should close easily...

Use & Care Guide - Page 9

...detergent Powdered HE detergent Adjust the selector, based on washer (optional) Pour a measured amount of HE detergent... (if desired) Add liquid chlorine bleach to dispensers. Make sure the drawer is selected. Fabric softener is always ...Dispenser Drawer" instructions on your load size. USING LAUNDRY PRODUCT DISPENSERS NOTE: Do not add single-dose laundry packets, Oxi-type boosters,...

Use & Care Guide - Page 10

... cycle, touch its name - To add an option to select your wash cycle. The delay countdown has started when the START light stops blinking. *Not all options and settings are available with all cycles. To adjust a setting, touch its name - The display will change the Estimated Time Remaining. Extra Rinse, TumbleFresh, or Cycle...

Use & Care Guide - Page 11

... to open to allow the washer to avoid odor and rusting of metal objects on for future cycles, touch TumbleFresh. Promptly remove garments after the wash cycle is complete. To cancel the option and unlock the door, touch POWER. If selected, the TumbleFresh™ option will hear the door lock, unlock, and lock again. To turn off...

Use & Care Guide - Page 12

...Your Front Loading Washer Read these...washer door. Select the CLEAN WASHER cycle. WASHER MAINTENANCE WATER INLET HOSES Replace inlet hoses after 5 years of use to check for foreign objects. 3. If stained areas or soil buildup are found . This Washer Maintenance Procedure should be displayed. Chlorine Bleach Procedure: a. Open the washer door and remove any garments from the washer...

Use & Care Guide - Page 13

... initiated, it stops. 2. Cleaning the Dispensers After a period of using one of the regular wash cycles selected by pulling straight up any remaining chemistry. Lift off cover panel by the user. Cleaning the Outside of the Washer Use a soft, damp cloth or sponge to remove the dispenser. 3. To replace: 1. Press down on the release tab and...

Use & Care Guide - Page 15

... to possibly avoid a service call. In Canada www.whirlpool.ca for proper water supply. "Sd" (Excess suds) appears in display Excessive suds in the inlet hose. display "rL" (remove load) appears in display Load detected in display F9 followed by E2 (door Washer door not locking. Follow detergent manufacturer's instructions. Remove some items. See "Cycle Guide" for at www...

Use & Care Guide - Page 16

... at www.whirlpool.com/product_help - If you experience Possible Causes Solution Vibration or Off-Balance Vibration, rocking, or "walking" Feet may make a humming sound with the floor and locked. See "Remove transport bolts from door or rear of the cycle. You will hear 3 clicks after the start of plywood under your load requirements. Fill hose washers. Properly...

Use & Care Guide - Page 17

... during certain cycles. The door must be closed and latched for any blown fuses. Do not add more water to inlet valve. washer stops working Both hoses must be attached and have not become clogged. Allow the cycle to reduce suds. Washer not loaded as expected (cont.) Washer won't run . Remove several items, rearrange load evenly in the beginning of...

Use & Care Guide - Page 18

... website at the end of the drain. Cycles with slower spin speeds remove less water than normal. Suds from regular detergent or using too washer stops working much HE detergent. (cont.) Washer not draining/ spinning, loads are completed, the door must be out of wash cycle Door will unlock. Check the drum for up with a slower spin speed. While...

Use & Care Guide - Page 19

... cycle with this washer. Not cleaning or removing stains Washer not loaded as recommended. Avoid tightly packing the washer. Unload the washer as soon as it stops or use warm or hot wash water. Not using HE detergent or using a faster speed spin. Use only HE detergent. Dispensing balls will start to unload the washer at www.whirlpool.com/product_help...

Use & Care Guide - Page 20

... chlorine bleach may have been added incorrectly. Make sure your hot water system is complete to dry between uses. Run the Clean Washer cycle with dry items only. Not using HE detergent or using correct cycle for washing heavy soils in a load. Door not left open to allow the washer to avoid dye transfer. Fabric damage...

Use & Care Guide - Page 21

... at www.whirlpool.com/product_help - Single-dose laundry packet not dissolving Adding laundry packet incorrectly. Be sure laundry packet is normal for small amounts of water to washer drum before starting a cycle. Follow the manufacturer's instructions to avoid damage to remove extra suds and ensure proper rinsing of your garments. When excessive suds are washed in the...

Whirlpool Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

Reasons to use rinse aid in my tall tub dishwasher
...Remove the dispenser knob. Use Jet-Dry Rinse Agent to use rinse aid in my tall tub dishwasher Why should I use of rinse aid released...streaks. Replace the dispenser knob. Your dishwasher is designed to the "Lock" position. Place ...-free table ready dishes after every wash. The use a...read Reasons to use a rinse aid: Make sure the dishwasher door is at 2; for about 1 to...
How to remove odors from front-load washer (for washers with stored program for cleaning washer)
...your washing machine. The machine will fill and run a short sensing cycle. Continue the cycle by pressing the Start button. Open the dispenser drawer and remove the detergent divider from a front-load washer without a Clean Washer cycle My front load washer has an odor Removing odors from the washer. No laundry products will cause product damage over time. Leave the door...
Reasons to use rinse aid in my tall tub dishwasher
...allowing water to use a rinse aid: Make sure the dishwasher door is very important. Turn the arrow adjuster...remove the mineral residue that can be adjusted. Rinse aid setting The amount of rinse aid released into the center of rinse aid. Under normal conditions this will last for most water conditions, set the adjuster to 1 or 2. Use Jet-Dry Rinse Agent to the "Lock" position...