Home » Whirlpool » Laundry Dryers » Whirlpool WED94HEXW

Whirlpool WED94HEXW Support Question

Find answers below for this question about Whirlpool WED94HEXW.
Need a Whirlpool WED94HEXW manual? We have 4 online manuals for this item!

Whirlpool Overview Questions Manuals Reviews Videos Research

Question posted by reagynrahaim on July 23rd, 2017

Convert To Gas

can you convert this dryer to gas instead of electric?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Odin on July 23rd, 2017 12:11 PM

This answer was accepted by the poster of the original question.

Odin

Member since:
April 10th, 2010

Points: 41,236,700

1,100
points

No. (Sorry.)

Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.

Related Whirlpool WED94HEXW Manual Pages

Dimension Guide - Page 1

...) The Vent system chart provides venting requirements that may be used. Electric Dryer Installation Instructions PRODUCT MODEL NUMBERS WED94HEX, WED95HEX, WED97HEX, WEDXXHEX Electrical: This dryer requires a 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate...

Installation Instructions - Page 1

... INSTRUCTIONS Para una version de estas instrucciones en español, visite www.Whirlpool.com Table of Contents DRYER SAFETY 2 Installation Requirements 3 Tools and Parts 3 Location Requirements 4 Electrical Requirements 4 INSTALL LEVELING LEGS 6 ELECTRICAL INSTALLATION 7 Power Supply Cord Connection 8 Direct Wire Connection 10 VENTING 13 Venting Requirements 13 Plan Vent System 14...

Installation Instructions - Page 2

DRYER SAFETY IMPORTANT: When discarding or storing your old clothes dryer, remove the door. 2

Installation Instructions - Page 3

..." and "Venting Requirements" before starting installation. The kit should be type SRD or SRDT and be required, depending in dryer drum. Check existing electrical supply and venting. The cord should contain: ■■A UL listed 30-amp power supply cord, rated 120/240 volt minimum. Check that opens to ...

Installation Instructions - Page 4

... using the "Y" connector and short hose (if needed) which are required. If using power supply cord, a grounded electrical outlet located within 4 ft. (1.2 m) of the water fill valves, and water pressure of dryer. ■■The dryer must not be installed or stored in an area where it will be exposed to water, weather...

Installation Instructions - Page 5

... built after 1996, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor is permanently connected to the dryer must be removed from the neutral conductor. Electrical Connection To properly install your dealer. The green ground wire of the 4-wire power cord must determine the type of...

Installation Instructions - Page 6

... neutral conductor must be identified by direct wire: Power supply cable must have three 10-gauge copper wires and match a 3-wire receptacle of the 2 dryer back corners. Prepare dryer for leveling legs If connecting by a white cover. 3-wire receptacle (10-30R) Then choose a 3-wire power supply cord with ring or spade terminals...

Installation Instructions - Page 8

... strain relief. Tighten strain relief screws just enough to 4-Wire Power Supply Cord Connection on strain relief). Prepare to strain relief Spade terminals with the dryer cabinet and be in place. Put the tabs of the two clamp sections (C) into the hole below the terminal block opening (B) so that the wire...

Installation Instructions - Page 9

... ground wire 1. Connect neutral wire (white or center) (C) of dryer rear panel. Finally, reinsert tab of terminal block cover into slot of... terminals with hold -down screw. Remove center screw A B F Connect ground wire (F) (green or bare) of dryer rear panel. Connect remaining wires Remove center terminal block screw (B). 2. Finally, reinsert tab of terminal block cover into ...

Installation Instructions - Page 10

...mm) (251"mm) (127 5" mm) Direct wire cable must have a tight fit with the dryer cabinet and be moved if needed. Tighten strain relief screw against the direct wire cable. Reaching inside... 1" (25 mm). The strain relief should have 5 ft. (1.52 m) of extra length so dryer may be in a horizontal position. Remove neutral ground wire (E) from remaining 3 wires. Prepare your wiring...

Installation Instructions - Page 11

... direct wire cable under center terminal block screw (B), hook facing right. Finally, reinsert tab of dryer rear panel. Squeeze hooked ends together and tighten screw. 4. Connect remaining wires Remove center terminal .... 5. Place hooked end of neutral wire (white or center) (C) of extra length so dryer may be moved if needed. Connect neutral ground wire and neutral wire B E C 3-Wire...

Installation Instructions - Page 12

... screws. A 4. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Prepare to Venting Requirements. Connect remaining wires E B Place ends ...and neutral wire B E C Place hooked ends of dryer rear panel. Secure cover with hold -down screw. Now, go to an adequate ground. Optional External Ground for your electrical connection method, as shown on page 8 or 10....

Installation Instructions - Page 13

... tape. 13 NOTE: If using an existing vent system, clean lint from ground or any gas vent, chimney, wall, ceiling, attic, crawlspace, or a concealed space of a building. Replace...: Louvered Hood Acceptable Style: Box Hood WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS. Venting Venting Requirements Exhaust hoods: ■■ An exhaust hood should...

Installation Instructions - Page 14

...drying performance: ■■Use the following Vent System Chart to determine type of dryer. ■■Reduce performance, resulting in Vent system chart. NOTE: Do not ... vent length and elbows needed for mobile homes: Exhaust vent must not terminate beneath the mobile home. Dryer B Elbow C. Wall D. Vent length necessary to use fewest number of elbows and turns. ■■...

Owners Manual - Page 5

... from your energy savings. Wash any starched or new garments prior to efficiently dry laundry. n Use the shortest length of wrinkle-free cotton, cotton-polyester blend, common knits, and synthetic...savings and enhanced fabric care from the exhaust hood. n Remove lint and debris from the dryer. During Automatic Cycles, drying air temperature and moisture level are not covered by the warranty ...

Owners Manual - Page 6

... to stop/cancel a cycle at any time. 2 CYCLE CONTROL KNOB Use your dryer's cycle control knob to select available cycles on and off. CONTROL PANEL AND FEATURES Not all features and cycles are available on all models. 11-cycle models 2 1 3 4 5 8 7 8-cycle models 2 1 3 4 6 5 1 POWER BUTTON Press to turn the dryer on your laundry load.

Owners Manual - Page 10

... Wet lint is hard to tumble freely. Push the lint screen firmly back into place. Place laundry in the dryer. Items need to remove. Pull the lint screen straight up. Do not rinse or wash screen... Clean the lint screen before operating this appliance. 1. USING YOUR DRYER WARNING: To reduce the risk of fire, electric shock, or injury to remove lint. Press POWER Press the POWER button to ...

Owners Manual - Page 13

.... These stains are not harmful to your load is hard to both sides of the dryer. As needed cleaning Laundry detergent and fabric softener residue can cause overheating and damage to remove. Wet both the dryer and fabrics. Thoroughly dry lint screen with your fingers. The control panel has an indicator light to...

Owners Manual - Page 14

... of replacement. Shut off water faucet. 6. Flush water pipes. Plug in dryer or reconnect power as described in gas supply line. 3. Disconnect power. 2. Transport hose separately. 5. Steam models only... hose failure. This helps to avoid unintended flooding (due to dryer pipe. 4. Gas models only: Disconnect gas supply line pipe and remove fittings attached to a water pressure ...

Owners Manual - Page 15

... exhaust vent is blown or circuit breaker has tripped. Electric dryers use . Electric dryers require 240-volt power supply. Dryer hasn't been used during Automatic cycles. Replace the fuses or reset the circuit breaker. On gas dryers, you experience Possible Causes Solution Dryer Operation Dryer will bounce, causing the dryer to possibly avoid a service call. When balled up in...

Whirlpool Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

The ice maker on my upright freezer is not producing ice or not enough ice
... - See "Ice maker" below . Find a local service provider: Product Category Washer or Dryer Refrigerator or Freezer Dishwasher Electric Range, Oven or Cooktop Gas Range, Oven or Cooktop Microwave Trash Compactor Window Air Conditioner Hot Water Dispenser Vent Hood Ice Machine Commercial Laundry Vacuum Cleaner Central Vac Dehumidifier Using the control: Turn the freezer temperature...
The oven burner flames on my gas range are yellow or noisy
... used? What should I do I regulate the flames sizes on my gas modular downdraft cooktop? The appliance may have been improperly converted. Gas surface burner performance The oven temperature on my gas range is either too high or too low My gas oven won't operate Contact a service technician or see "Assistance or Service" section below. The...
How do I clean the filters in my vent and how often should I do so?
...I need replacement parts for my vent Maintaining your canopy-style range hood How does the oven vent on my convertible range hood? This safety feature stops the blower and raising mechanism until the filter is inactivated. When the filter... the aluminum filter/light lens, or charcoal filter pads on my gas range work? How do I clean the filters in my vent and how often should I do so?