Whirlpool WDF110PABB Support Question
Whirlpool WDF110PABB Support Question
Find answers below for this question about Whirlpool WDF110PABB.Need a Whirlpool WDF110PABB manual? We have 2 online manuals for this item!
Question posted by jarens on April 11th, 2017
Wdf110pabb4
I need part number for heat element assembly
Current Answers
Answer #1: Posted by Odin on April 12th, 2017 6:37 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,660
Member since:
April 10th, 2010 Points: 41,236,660
W10518394. You can order it at https://www.repairclinic.com/Shop-For-Parts/a9b5c42d1931691/Model-WDF110PABB4-Whirlpool-Dishwasher-Heating-Element-Parts.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Whirlpool WDF110PABB Manual Pages
Energy Guide - Page 1
A) Government
Federal law prohibits removal of $1.218 per therm.
• For more information, visit www.ftc.gov/appliances. (P/N W10531938 Rev. Dishwasher Capacity: Standard
Whirlpool Corporation Models: WDF110PAB**,
WDF111PAB**
Estimated Yearly Operating Cost
(when used with an electric water heater)
$29 ▼
$20
$50
Cost Range of ...
Installation Guide - Page 2
... installation.
2 WARNING
You can be killed or seriously injured if you don't immediately follow instructions. Close dishwasher door until completely installed.
We have provided many important safety messages in this dishwasher as specified in serious injury or cuts.
You Need to meet all electrical and plumbing national and local codes and ordinances. The...
Installation Guide - Page 3
... Requirements" section.
Parts needed:
All Installations Tools needed:
Other parts you may also need :
NOTE: Some parts available for first-time installations Tools needed:
Parts supplied:
Parts needed:
Make sure all these parts are included in the literature package.
*Power cord grommet included only on power cord models or in dishwasher. INSTALLATION REQUIREMENTS
Tools and...
Installation Guide - Page 4
..." section.
4 Motor should not touch the floor.
A moisture barrier accessory (Part Number 4396277) is available from freezing is not level with or contact dishwasher motor or legs. Check location where dishwasher will be left unused for loading and unloading dishes. Do not install dishwasher over carpeted flooring.
■ convenient access for a period of the...
Installation Guide - Page 6
...are connecting the air gap, a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.
or 20-amp, ...Number 4396897RP). copper tubing with 20 to 120 psi (138 to 862 kPa) water pressure can be verified by a licensed plumber.
■ 120°F (49°C) water at dishwasher O.D.
Drain Requirements
■ A new drain hose is resistant to heat...
Installation Guide - Page 7
... Hazard Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. New Utilities" section. See "Product and Cabinet Opening Dimensions" section.
7 ...Prepare Cabinet Opening- If the water line and the cable extend to the locations shown, proceed to the dishwasher cabinet opening. Drill a 1¹⁄₂" (3.8 cm) hole in cabinet side or rear. Prepare...
Installation Guide - Page 8
... water supply line.
8 Metal cabinet: Cover hole with grommet included with grommet (Part Number 302797 not provided). Wood cabinet: Sand the hole until smooth.
Metal cabinet: Cover hole... from moving when dishwasher is moved into cabinet opening from power supply through the left side of cabinet opening ).
Option B, Direct Wire:
Helpful Tip: Wiring the dishwasher will make water ...
Installation Guide - Page 9
... codes and ordinances. Flush water into the cabinet opening to connect it from moving when dishwasher is required. Tape drain hose to the floor in area shown. Turn shutoff valve to "... into cabinet opening.
This will keep it to the dishwasher inlet on the front left side of opening where drain connection will be made.
If needed, drill a 1¹⁄₂" (3.8 cm) diameter...
Installation Guide - Page 10
...;₂" to 2" (3.8 to remove plug.
3. Use pliers to 5 cm) screw-type clamp (not provided).
5. If the drain hose was cut if needed . Option A, Waste disposer - Attach drain hose to disposer inlet.
10 Use a rubber hose (not provided) with screw-type clamps (not provided) to... be made before the drain trap and at least 20" (50.8 cm) above the floor where the dishwasher will be installed.
Installation Guide - Page 11
...air gap.
NOTE: Do not cut if needed. Use a rubber hose (not provided) with large drain hose clamp (provided). Tip Over Hazard Do not use dishwasher until installed in back or other injury....Doing so can result in cabinet opening to fasten the insulation down on open and move and install dishwasher. Do not use a 1¹⁄₂" to 2" (3.8 to move into position. Be ...
Installation Guide - Page 12
... the left when tightening conduit nut.
Pull cord through strain relief in terminal box.
12
Strain relief is provided with the installation of dishwasher door frame and place dishwasher on its back. Retain for later use.
Make Power Supply Cord Connection
Option A, Power Supply Cord:
Using a ¹⁄₄" hex-head socket...
Installation Guide - Page 13
... closest to the plug to be sure both are secured. Electrical Shock Hazard
Electrically ground dishwasher.
NOTE: Do not pre-twist stranded wire. Gently tug on wires to maximize the ...screwdriver and previously removed screw to do so.
13
Connect ground wire to 16-gauge dishwasher wiring. If needed, see website for animated representation of the green ground wire.
Do not remove any...
Installation Guide - Page 14
... for additional clearance. Refer to adjust the leveling legs. Rear and front leveling legs are approximate. This will allow the dishwasher to fit into a 33¹⁄₂" (85.1 cm) high cabinet opening, but the dishwasher will need to the correct height for your cabinet opening from underside of countertop to floor where...
Installation Guide - Page 15
... the area shown to avoid movement when the dishwasher is wood, laminate or another hard surface, install using Option Number 2. Using a pair of the dishwasher collar as needed in use.
NOTE: Do not attach the dishwasher. IMPORTANT: The dishwasher must be securely attached to floor to bring the dishwasher up .
NOTE: Shims must be done later.
Choose...
Installation Guide - Page 16
... not use Teflon®† tape with compression fittings.
With another person holding the dishwasher to keep it will need to elbow using ⁵⁄₈" open and close to cabinet opening. Panel or console may dent. Move Dishwasher Close to do so.
Failure to Cabinet Opening
Check that the ³⁄₄...
Installation Guide - Page 17
... firmly against the front panel. NOTE: Springs should be easier to route end through hole in the same notches on front of the dishwasher. With some installations, it may need to adjust alignment to back in the opening. the blanket reduces the sound level. ■ If using power cord, make sure to...
Installation Guide - Page 18
... Connect to Water Supply
Connect to Drain
Be sure rubber washer is properly seated in drain hose.
If needed , see website for leaks. After hose is tight. Visit www.whirlpool.com/drain under 90° elbow... hose clamp onto the small end of the coupling. If needed , see website for animated representation of this step. Hand tighten until the coupling is connected, remove towel.
Installation Guide - Page 19
... are secured.
19
NOTE: Do not pre-twist stranded wire. Twist on wires to 16-gauge dishwasher wiring. Do not use an extension cord. Securely tighten ground connector screw. Failure to follow these ... U-shaped hook. Strain relief is not supplied with the dishwasher. Make Direct Wire Electrical Connection
NOTE: If the power supply cord was connected earlier, proceed to "Secure...
Installation Guide - Page 20
... when door is still level front-to-back and side-to secure cable.
Secure Dishwasher in cabinet opening. Visit www.whirlpool.com/electrical under FAQ tab. Open dishwasher door, remove lower dish rack, and place towel over pump assembly and lower spray arm of this step. Close cover ensuring wires are not pinched...
Installation Guide - Page 21
... Reinstall the lower dish rack. If it does, adjust leveling legs.
Remove towel from dishwasher. Check that top of door does not contact screws, brackets or countertop. Adjust if ...access panel against the dishwasher leg. Open door and check that space between dishwasher cabinet opening and tub is not equal, loosen bracket screws secured and shift tub.
If needed, see website for ...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Stains on tub or dishes in my dishwasher
...; Lipsticks are often wax or petroleum-based, so a high-temperature wash is needed more evident at the heater, since heat accelerates the staining. Is there yellow discoloration near the heating element can be hand-washed and not washed in the dishwasher because they will reduce the likelihood of citric acid crystals to the... -
What is the proper procedure for starting my dishwasher?
...dish load. After sensing is complete, the display will show the number of lights in my dishwasher? The door automatically latches and starts filling. With the ACCUSENSE TM...the sensing light glows while the dishwasher heats the water to a set temperature. The time displayed does not include the time needed . Properly load the dishwasher. Make sure nothing prevents ... -
Foods undercook during convection and combination cooking
... "0° See the Oven Temperature section below ). Press the number pads to increase or to place in Fahrenheit or Celsius. Oven...need to escape from the door being open , the more heat is supplied with leavening ingredients, such as yeast, baking powder, baking soda and eggs. Foods are not prepared and ready to decrease the temperature in the oven. Heating elements...
Similar Questions
We Replaced The Burned Out Heating Element And It Still Will Not Heat?
What is the next step?
What is the next step?
(Posted by dthomas62457 1 year ago)
Our Dishwasher Was Not Doing A Heated Dry. We Changed The Heating Element Which
Our dishwasher quit heating the water - we noticed the heating element had burned so we replaced it....
Our dishwasher quit heating the water - we noticed the heating element had burned so we replaced it....
(Posted by dday46 8 years ago)
Does The Whirlpool Wdt790saym Have A Heating Element To Heat Water? Or Dry Only?
(Posted by davis651 11 years ago)
Du850swpb3 Dishwasher=how Hot Is The Heat Boost Cycle?
I need to know if the "heat boost" option gets the water over 140 degrees F
I need to know if the "heat boost" option gets the water over 140 degrees F
(Posted by danik719 11 years ago)
Heating Element Will Not Work
hello, i replaced the heating element and it still doesnt work? is there anything i can do to troubl...
hello, i replaced the heating element and it still doesnt work? is there anything i can do to troubl...
(Posted by part23333 12 years ago)