Whirlpool DU1100XTPT Support Question
Whirlpool DU1100XTPT Support Question
Find answers below for this question about Whirlpool DU1100XTPT.Need a Whirlpool DU1100XTPT manual? We have 1 online manual for this item!
Question posted by curt21777 on March 21st, 2013
Replaced Blown Fuse. Ran Good Once Then Blew Again On Last Rinse Cycle
We had some power surges in our electrical because of a blizzard and the next time we ran the dishwasher it ran until the last cycle and then blew the bi-metal fuse. Replaced with a new one and it ran ok for one time then blew the fuse again on the last rinse cycle. did not completely drain the water. Everything looks ok but will not turn on or light up. what to check next?
Current Answers
Related Whirlpool DU1100XTPT Manual Pages
Installation Instructions - Page 7
... cabinet walls or floor as specified in chart:
OPENING FOR: water line drain line direct wire power supply cord
DIAMETER: 1/2" (1.3 cm) 1-1/2" (3.8 cm) 3/4" (1.9 cm) 1-1/2" (3.8 cm)...1/2 po)
filerie directe
1,9 cm (3/4 po)
cordon électrique 3,8 cm (1 1/2 po)
*Measured from dishwasher.
*Mesuré à partir du point le plus bas du dessous du comptoir. Installation Installation
24" (...
Whirlpool Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
The water temperature is not correct - Cabrio® washer with Dispensers in Corners
... is normal. Cabrio® Is the washer new or just recently installed? Are you than I expect - The wash water temperatures may notice lower hot or warm water temperatures. Turn the water back on and make sure that the rubber gaskets are cooler than those of time may use up operation. This is not correct... -
The water temperature is not correct - Front-load washer
... or FH - Check to find them online. If so, turn off the water lines at the nearest sink until you washing many loads in each of time? See the Installation Instructions for details. You may use up operation. Top-load washer Warm or hot wash temperatures are no leaks. Is the washer new or just... -
The water temperature is not correct - Top-load HE washer with Dispenser Drawers - video
... of time may be cooler than I expect - This is not correct - Top-load washer Warm or hot wash temperatures are cooler than your water heater can make sure that the rubber gaskets are no leaks. Top-load washer Display shows LF - Learn more about the temperature control: Turn the water back on...
Similar Questions
Dishwasher Does Not Operate
when start button is pushed the "normal" light blinks until power is removed Dishwasher does not sta...
when start button is pushed the "normal" light blinks until power is removed Dishwasher does not sta...
(Posted by donscottsr 9 years ago)
Whirlpool Wdt910ssym0 Will Not Completely Drain
it does not leak onto the floor but water always remains in the bottom.. the screens are not dirty.....
it does not leak onto the floor but water always remains in the bottom.. the screens are not dirty.....
(Posted by kddillard48 10 years ago)
Does Not Drain Water From The Tub.
It will not drain the tub after a wash and also when using cancel/drain. Help?
It will not drain the tub after a wash and also when using cancel/drain. Help?
(Posted by nelsonklinek 11 years ago)
My Whirlppol Du1010xtxq Has Blown The Fuse Twice Within The First Year I've
bought it. Any solutions?
bought it. Any solutions?
(Posted by jtbusiness 11 years ago)
Whirlpool Du1100xtpt Dishwasher Fuse Is Blowing Off Before End Of Cycle.
I have du1100xtpt3 whirlpool dishwasher having problem with fuse. Before end of cycle (normal wash),...
I have du1100xtpt3 whirlpool dishwasher having problem with fuse. Before end of cycle (normal wash),...
(Posted by kknewhome 12 years ago)