Weider 8530 Support Question
Weider 8530 Support Question
Find answers below for this question about Weider 8530.Need a Weider 8530 manual? We have 1 online manual for this item!
Question posted by Sarge24509 on September 23rd, 2015
Pulley Assembey F
How to assemle pulley on model no. 8530 Butterfly, press and squat exercise
Current Answers
Answer #1: Posted by TommyKervz on September 24th, 2015 12:57 PM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,813
Member since:
January 10th, 2013 Points: 17,776,813
Please call Customer Care Department at 1-800-999-3756 or click this link https://www.iconservice.com/CustomerService/contactUs.do?dr=WR to receive service assistance.
Related Weider 8530 Manual Pages
User Manual - Page 1
Write the serial number in this manual before using this manual for reference. Model No. Serial Number Decal
(Under Seat)
QUESTIONS? If you have questions, or if there are committed to providing complete customer satisfaction.
As a manufacturer, we are ...
User Manual - Page 3
... Replace any time while exercising, stop immediately and make sure that the cables remain on all times. If you are on the pulleys at all of the pulleys.
11. Inspect and ...only on a foot plate when performing an exercise that could become pinched between the squat arm upright and the squat arm.
7. Never release the press arm, butterfly arms, squat arm, leg lever, lat bar or nylon...
User Manual - Page 4
... yourself with using the home gym system. Whether your goal is WESY8530C2. The model number is to tone your body, build dramatic muscle size and strength, or ... you want. Lat Bar High Pulley Station
Butterfly Arms
VKR Arms Backrest
Squat Arm Press Arm
Weight Stacks Weight Pin
Leg Lever Low Pulley Station
Foot Plate
4 The WEIDER® 8530 offers a selection of weight stations...
User Manual - Page 5
...for shipping. Assembly will also be on the side shown.
Slide the VKR Upright (74) and the Squat Arm Upright (56) onto the 5/16" x 2 1/2" Carriage Bolts (1) in a cleared area and... into the indicated end of the Base (4). Press a 2" Inner Cap (27) into five stages: 1) frame assembly, 2) press and butterfly arm assembly, 3) cable and pulley assembly, 4) seat and backrest assembly, and ...
User Manual - Page 8
.... The Plastic Bushings should fit on each welded spacer on the side shown. Attach the Press Frame (17) to the Right Arm (48) with the 3/8" x 8" Bolt and a 3/8" Nylon Locknut (21).
9.
Arm identification is in the Base.
Lubricate the 3/8" x 8" Bolt (59). Be sure that the pulleys are on the Press Frame (17). Press a 1" Round Inner Cap...
User Manual - Page 9
... water.
Slide a 10" Pad (45) onto the lower end of the "V" Pulley (50) to identify the Right Arm. Press two 1" x 2" Inner Caps (87) into the indicated end of the Handle.
Press a 1" Round Inner Cap (49) into the lower ends of the Squat Arm (84) in the same manner.
Be sure that the indicated bracket...
User Manual - Page 10
... (68) and the 5/16" Nylon Locknut (not shown). Wrap the Medium Cable (58) around the "V"Pulley (50) on the Right Arm (48). Be sure that the Cable is positioned to hold the Cable in...12) and a 3/8" Nylon Locknut (21). IMPORTANT: Do
not overtighten the bolts and nuts securing
the pulleys. Attach the "V"-Pulley and a Long Cable Trap (31) to the upper hole in place. During steps 13 to 25,...
User Manual - Page 11
... is turned to hold the Cable in the groove of the Press Frame (17) and that the Cable is routed around the Pulley as shown. It has been shown disassembled for easy part identification.)... Be sure that the Cable is in place and that the Cable is between the Pulley and the Press Frame. Tighten the 3/8" Nylon Locknut (21) and 3/8" x 3 3/4" Bolt (88). Attach the ...
User Manual - Page 13
...Attach the Pulley and a ...Wrap the Long Cable (72) around a 3 1/2"
24
Pulley (15). Wrap the Long Cable (72) around a 3 1/2" Pulley (15). Route the Long Cable (72) around the 3 1/2" Pulley (15) on the Stabilizer (5) with the 3/8"
x ... Tighten the 3/8" Nylon Locknut (21) and the 3/8" x 2" Bolt (not shown). Attach the Pulley and a Cable Trap (66) to hold the Cable in place.
66 15
15 5
21
84...
User Manual - Page 14
... view from other side
A
21 9
76 56
72 67 50 31
B 92 94
72
SEAT ASSEMBLY
26. Attach the "V"-Pulley and a Long Cable Trap (31) to the Seat (13) with two 1/4" x 2 1/2" Screws (43) and
two...end of the Seat (13) to pivot.
25
50 72
Insets show view from the other side of the Squat Arm Upright (56). Press a 1 1/2" Inner Cap (32) into the Seat Frame (36).
27
13
Insert a 1/4" x 2" ...
User Manual - Page 16
... handle on page 17 of the cables
does not move
smoothly over the pulleys. IMPORTANT: If the cables are not
properly installed, they may be damaged...Armrest (78) to be explained in the locations shown:
B
A -8530
B -HIGH PULLEY
C -BUTTERFLY
D-MILITARY PRESS
A
E -SQUAT STATION
F -BENCH PRESS
G-LEG DEVELOPER
H-LOW PULLEY
I -VKR I
Make sure that the cables move smoothly, find ...
User Manual - Page 17
...23) with two Cable Clips. CHANGING THE WEIGHT SETTING
The WEIDER 8530 features two weight stacks. For some exercises, the Chain (52) should be changed from
the weight setting...pulleys, the press arm, and the butterfly arms.
The rear weight stack is in increments of the exercise will be performed. Note: Due to
the cables and pulleys, the actual amount of
resistance at each exercise...
User Manual - Page 18
... Knob (40). Attach the other numbers refer to the 6.5 lb. "Top" refers to the 12.5 lb. For some exercises, the Seat (13) must be removed.
top weight. WEIGHT PRESS ARM BUTTERFLY ARM LEG LEVER HIGH PULLEY LOW PULLEY SQUAT ARM
PLATES
(lbs.)
(lbs.)
(lbs.)
(lbs.)
(lbs.)
(lbs.)
Top
20
10
15
14
24
31
1
45
22...
User Manual - Page 19
...removed from these cables three ways:
58 66
See drawing 1. Move the 3 1/2" Pulley (15) to another hole in the Squat Arm Upright (56).
Do not use the home gym system. TIGHTENING THE CABLES
...the 3/8" Nylon Locknut (21) and the 3/8" x 5" Bolt (not shown) from the Cable
Trap (66), Pulley, and Long "U"-Bracket. If a cable tends to slip off the weight stack. Remove the cable and re-...
User Manual - Page 20
... Short Cable (23). Be sure that the cable traps do not touch or bind the cables.
2
1-High Pulley
2
7
3
Long Cable (72)
6-Squat Arm Bracket
4
5 6
4
Medium Cable (58)
TOP VIEW
5-Long "U"-Bracket
5-This side of Pulley must be positioned so that the three cables and cable traps have not been correctly routed, the home...
User Manual - Page 23
When ordering parts, please be prepared to give the following information: • the MODEL NUMBER of the product (WESY8530C2) • the NAME of the product (WEIDER® 8530 weight system) • the SERIAL NUMBER of the product (see the front cover of this manual) • the KEY NUMBER and DESCRIPTION of the part...
User Manual - Page 24
...PRODUCT WARRANTY REGISTRATION
IMPORTANT: MAIL WITHIN 14 DAYS OF PURCHASE
NAME:
PHONE:
ADDRESS:
COUNTY:
POSTCODE:
MODEL NO.
J Magazine
J Friend/relative
J Newspaper Ad
J Store
J Other
7) What was the ...forth above limitation may also have purchased,
would you consider purchasing fitness equipment from the date of exercise equipment do you read regularly?
J Yes
J No
J No...
User Manual - Page 25
... part refers to the key number of the part. The number in parenthesis below each stage is divided into five stages: 1) frame assembly, 2) press and butterfly arm assembly, 3) cable and pulley assembly, 4) seat and backrest assembly, and 5) VKR assembly. Note: Assembly is packaged separately. Important: Some parts may have been pre-assembled for...
User Manual - Page 28
3/8" x 3 1/2" Bolt (16) 3/8" x 3 3/4" Bolt (88) 5/16" x 5" Bolt (68)
1/4" x 3/4" Screw (18)
Cable Clip (53)
1" Retainer (69)
3/8" x 5 1/2" Bolt (93) 5/16" x 6" Bolt (60) 3/8" x 8" Bolt (59)
1 1/4" x 2 1/2" Plastic Bushing (89)
1" x 7/8" Plastic Bushing (90) 3 1/2" Pulley (15)
(Not shown to scale) "V"-Pulley (50) (Not shown to scale)
User Manual - Page 29
...Squat Arm Squat Arm Pad 3/8" x 2 1/2" Bolt 1" x 2" Inner Cap 3/8" x 3 3/4" Bolt 1 1/4" x 2 1/2" Plastic Bushing 1" x 7/8" Plastic Bushing 1/2" x 17/32" Spacer 3/8" Jam Nut 3/8" x 5 1/2" Bolt 3/8" x 2 1/4" Bolt 3 1/2" Low Pulley Inner Cap User's Manual Exercise... Screw 1 3/4" Inner Cap 10" Pad Press Arm Left Arm Right Arm 1" Round Inner Cap
Key No. PART LIST-Model No. WESY8530C2
R1202A
Key No.
Similar Questions
Weider 8530
where can I download a copy of the exercises chart for the weider 8530 home gym
where can I download a copy of the exercises chart for the weider 8530 home gym
(Posted by lafrance57 4 years ago)
I Had To Take My 8530 Unit Apart Can Figure Out How To Recable It An I Have The
Cant Figure Out How To Re Cable My 8530 Unit Had To Take Apart
Cant Figure Out How To Re Cable My 8530 Unit Had To Take Apart
(Posted by NOVA64YR 6 years ago)
How To Install Cable And Pulley On Weider Pro 4850
can you help me install new weider pro 4850 cable and pulley?
can you help me install new weider pro 4850 cable and pulley?
(Posted by verrolburnett 8 years ago)
Assemling Home Gym
I am to assemble ez 100 home gym .I have lost manual. pl help in getting manual o line
I am to assemble ez 100 home gym .I have lost manual. pl help in getting manual o line
(Posted by sunilbadhwar 8 years ago)