Troy-Bilt TB146 Support Question
Troy-Bilt TB146 Support Question
Find answers below for this question about Troy-Bilt TB146.Need a Troy-Bilt TB146 manual? We have 1 online manual for this item!
Question posted by psottak on July 14th, 2020
How To Remove Clutch Housing From The Engine When Replacing The Pull Start Assem
How do you remove the clutch and housing assembly from the starting assembly to change out a new starting assembly
Current Answers
Answer #1: Posted by INIMITABLE on July 14th, 2020 2:52 PM
INIMITABLE
Member since:
April 3rd, 2020 Points: 2,069,620
Member since:
April 3rd, 2020 Points: 2,069,620
Watch out this tutorial video;
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers
-INIMITABLE
Related Troy-Bilt TB146 Manual Pages
Operation Manual - Page 1
...
DO NOT squeeze the throttle control. IF THE ENGINE IS HOT
Go back to the operator's manual for additional starting position. NOTE: Do not over tighten the handlebar knobs.
Remove the fuel cap.
Pull starter rope in starting and troubleshooting information. NO ASSEMBLY TOOLS REQUIRED
Electric Starter or Power Start Bit Optional!
In cold weather (below 40...
Operation Manual - Page 2
...5500 IN U.S. Remove all bystanders, ... assembly, operating, maintenance, and repair information. Replace... parts that it to another. • If you are no sparks or flames. Wipe up . Breathing exhaust fumes can be equipped with the controls and proper use this unit only in the starting position whenever pulling the starter rope. Take extra care when working order, or the engine...
Operation Manual - Page 3
...UNIT. Unscrew the top of oil during future oil changes. DO NOT overfill. Refer to the unit's ...ring is in garden areas, around trees, etc. • Edging
NO ASSEMBLY TOOLS REQUIRED
Throttle...starting the unit. As little as 1% water in the fuel can cause premature engine wear and failure. Remove the cap from fuel spray. NOTE: This unit comes with the desired hole in the wheel assembly...
Operation Manual - Page 4
... need to another.
1. Always stand in the Assembly Instructions section.
3. Carbon monoxide
exhaust fumes can
penetrate the ground. 6. STARTING INSTRUCTIONS 1.
Using one location to turn the unit on its wheels. Pull the starter rope in the OFF (O) position until the engine comes to step 3. The engine does not start , go back to a complete
stop (Fig. 6).
4
With...
Operation Manual - Page 5
... be replaced at a time.
1. Refer to spread and remove excess oil. 6. Cleaning the Air Filter
1. Air Filter Cover
Fig. 16
5. Insert the hooks on the new tines ...Change the oil. Remove the retainer from entering the oil fill hole.
2. Slide on the air filter housing into the spark plug hole (Fig. 20) and pull the starter rope
slowly to a qualified service dealer:
• the engine...
Operation Manual - Page 6
...).
7.
Start the engine and allow it clockwise until fuel is visible Drain the fuel tank and add fresh fuel Replace the spark plug Clean or replace the air filter Adjust the idle speed
THE ENGINE LACKS POWER OR STALLS WHEN CUTTING
The fuel is old (over tighten. 8. Pull the starter rope slowly to Changing the Oil.
Remove the...
Similar Questions
What Would Cause My Pull Cord To Not Catch Anything?
(Posted by adamhawkins265 1 year ago)
Pull String
how do I replace the pull string on my Troybiltiller ?
how do I replace the pull string on my Troybiltiller ?
(Posted by gregschaffer67 3 years ago)
Pull Start Assy
cord doesn't recoil when trying to start, replaced pull cord assy same results
cord doesn't recoil when trying to start, replaced pull cord assy same results
(Posted by dwaynegreer1 4 years ago)
Unable To Start Tb146 D.c. Tiller
tries new gas, cleaned filter & plug. Still cannot get tiller to start
tries new gas, cleaned filter & plug. Still cannot get tiller to start
(Posted by Bigdanno9 6 years ago)