Home » Troy-Bilt » Lawn & Garden » Troy-Bilt CS 4325

Troy-Bilt CS 4325 Support Question

Find answers below for this question about Troy-Bilt CS 4325.
Need a Troy-Bilt CS 4325 manual? We have 1 online manual for this item!

Troy-Bilt Overview Questions Manuals Reviews Videos Research

Question posted by 1kat1bird on October 12th, 2022

Cs4325 B&s Carb Removal

I need to remove the carb to clean it. Unit won't start but runs with starting fluid spray

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Technoprince123 on October 12th, 2022 8:49 PM

This answer was accepted by the poster of the original question.

Technoprince123

Member since:
February 8th, 2021

Points: 1,205,190

1,110
points

https://youtu.be/PfG11nm0bXg

https://youtu.be/1SucPZU0XUo

Please response if this answer is acceptable and solw your problem thanks

Related Troy-Bilt CS 4325 Manual Pages

Operation Manual - Page 1

Model Series CS4265 & CS4325 WARNING READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY ...

Operation Manual - Page 3

...and ground it is in this machine without proper instruction. 5. Remove all instructions on the part of age to the eyes. 3....deadly gas. 7. Thrown objects which could result in operation. Before starting, check all instructions in this manual in the manual(s) before ...running. Preparation 1. Failure to protect your eyes. Never run an engine indoors or in personal injury.

Operation Manual - Page 4

...your machine should start making an unusual noise or vibration, immediately shut the engine off , wait until all times until fueling is complete. e. g. Move unit to a complete... When practical, remove gas-powered equipment from your face and body back and to build up . Replace gasoline cap and tighten securely. Clean up or carry machine while the engine is running . 17. ...

Operation Manual - Page 5

... outdoors. Box 361131 Cleveland, Ohio 44136-0019. Important Safe Operation Practices 5 Before cleaning, repairing, or inspecting, stop the engine and make certain the impeller and all... machine to the Consumer Products Safety Commission (CPSC) and the U.S. Failure to prevent unintended starting. Follow this manual for safe loading, unloading, transporting, and storage of seven (7) years...

Operation Manual - Page 6

.... Important Safe Operation Practices There are rotating blades inside BYSTANDERS Keep bystanders, pets, and children at least 75 feet from the machine while it is running. ROTATING BLADES Keep hands out of this power machine to the machine. THROWN DEBRIS Never operate without the chute deflector properly attached to persons who...

Operation Manual - Page 7

Chipper Chute (Model Series CS4325 Only) For shipping reasons, the unit is crated with gasoline as instructed in property damage...-Up Refer to the separate engine owner's manual for additional engine information. 1. Add oil provided before starting unit for at least two minutes after running. 7 Pull the spring latch upward. 2. See Figure 3-1. See Figure 3-2. 2. Refer to the separate...

Operation Manual - Page 8

... chute support. Use the spring latch to start engine. Lock Rod (Model Series CS4325 Only) The lock rod is located on the engine. Recoil Starter The recoil starter is discharged from the machine's reduction chamber through the chute deflector. 8 IMPORTANT: Never place branches with your unit's shredder blade, flails or impeller. Controls and...

Operation Manual - Page 9

... will pull slightly harder at this manual covers several different model units, different starting procedure. If the unit has a primer, prime the motor as instructed in a poorly ventilated area. It is completely normal and does NOT indicate a malfunction of the spark plug is running smoothly. Move throttle control lever to STOP position (if equipped...

Operation Manual - Page 10

... inches (Model Series CS4265) or three (3) inches (model series CS4325) into the chipper chute. • Apply intermittent pressure (force,... your hands to remove any debris found near the impeller, follow instructions under the heading Cleaning the Reduction Chamber ...from the chute deflector. See Figure 5-3. broomstick) to the unit's shredder blade, flails or impeller. Chipping WARNING: Never ...

Operation Manual - Page 11

... the reduction chamber becomes clogged, remove and clean as it could contaminate the fuel system. Engine Care Refer to the engine manual. • The spark plug should be cleaned and the gap reset once a season. Lubrication 1. NOTE: Cleaning with your unit. Follow the separate engine manual packed with a forceful spray of water is not recommended as...

Operation Manual - Page 12

...clean the surrounding area. Confirm that you can be hot if the engine has been running. When the area is disconnected and away from the clevis pin which extends through the housing and shredder screen. If attached, remove... chipper shredder has come to the chute deflector, if desired. 2. Remove clevis pin. Clean the surrounding area by scraping away debris. Pull on either side of...

Operation Manual - Page 13

...See Figure 7-1C. Pivot the shredder screen upward as instructed under the heading Cleaning the Reduction Chamber. Remove the chipper chute support brace from each blade. 8. NOTE: Use a 3/16...Remove the two flange nuts (and hex bolts) which secure it. Remove the chipper chute by hand until one of the two chipper blades is sharp. Retain the hardware. 3. C B A Model Series CS 4325...

Operation Manual - Page 14

... box (or socket) wrench on the inside of grinding to run and clear out all dirt from the heavy side until it aside...from rotating when removing the shredder blade. • • • • Allow the unit to prevent an unbalanced blade. Remove the two ...springs, bearings, and cables. Store equipment in a clean, dry area. Remove six flange nuts which secure the shredder blade to ...

Operation Manual - Page 15

... .030". 2. Clean fuel line; fill tank with clean, fresh gasoline. 6. Remove spark plug and adjust gap to OFF position. 3. Always run engine at full throttle. 4. Empty bag. 1. Unit running on fuel shut... to spark plug. 4. Spark plug boot loose. 2. Move throttle lever to FAST or START position. 2. Blocked fuel line or stale fuel. 4. Dirty air cleaner. 7. Carburetor out...

Operation Manual - Page 18

...of merchantability or fitness for rental expenses to new merchandise purchased and used in the United States and/or its territories and possessions, and by MTD Products Limited with respect...or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for a particular purpose, applies after the applicable period of the ...