Toro 20332 Support Question
Toro 20332 Support Question
Find answers below for this question about Toro 20332 - Recycler 190CC Personal Pace Lawn Mower.Need a Toro 20332 manual? We have 2 online manuals for this item!
Question posted by Campers264 on May 6th, 2013
I Have A Toro 20331. The Front Wheel Self Propelled Drive Does Not Work. Belt Is
Belt is good. Cable is good. Belt tightens. Wheels are fine. Spring is tight.
Current Answers
Answer #1: Posted by freginold on May 12th, 2013 7:46 AM
freginold
Member since:
December 20th, 2011 Points: 23,253,885
Member since:
December 20th, 2011 Points: 23,253,885
Hi, it sounds like you checked most things. It could be a worn or bad gear in the front drive section, or a bad bearing. Check the gears, and while you have them exposed make sure everything is lubricated according to the manual.
Related Toro 20332 Manual Pages
Operation Manual - Page 1
... to operate and maintain your product ready. This rotary-blade, walk-behind lawn mower is intended to special mechanical information and Note emphasizes general information worthy of California... an Authorized Service Dealer or at www.Toro.com. This spark ignition system complies with a spark arrester muffler. 22in Recycler® Lawn Mower
Model No. 20332-Serial No. 312000001 and Up Model No...
Operation Manual - Page 2
...lawn mower will be ordered through the engine manufacturer.
Poor footing could cause a slip and fall accidents, which could be sure of this mower could lose your footing; You could result in injury or death. As configured to potential personal...safety protective devices in place and working.
• Never leave a ...• Disengage the drive system, if so ... good artificial light.
•...
Operation Manual - Page 3
... Do not run the engine indoors or in contact with the rim of Gasoline
To avoid personal injury or property damage, use a nozzle lock-open device.
• If fuel is ... tighten securely. Do not use extreme care in safe working condition.
• Never tamper with manufacturer's recommended parts, when necessary.
• Mower blades are explosive.
• Extinguish all nuts and bolts tight ...
Operation Manual - Page 4
... the original machine manufacturer.
94-8072
104-7953
1. Safety and Instructional Decals
Important: Safety and instruction decals are located near areas of hand or foot, mower blade-stay away from moving parts.
5.
do not operate up .
4 Read the Operator's Manual.
1. Unlock
114-7982
1. stop the engine before servicing or performing maintenance...
Operation Manual - Page 5
..., SJ, SL, or higher. Max.
Install and tighten the handle knobs that covers the engine.
1
Installing the Handle... pour about 3/4 of the crankcase capacity of oil. Important: Route the cables to the operating position. 3. Note: When the crankcase is at the Full...
2
Filling the Engine with Oil
No Parts Required
Procedure
Important: Your mower does not come with oil in the engine, but it out (Figure...
Operation Manual - Page 7
... 10% ethanol because the fuel system could be damaged. Dipstick
Figure 8
3.
Move the mower to the fuel all season, mixing it with fresh unleaded regular gasoline (having an octane ...API service classification of 87 or higher) from igniting the gasoline, place the container and/or mower directly on the ground before filling, not in an approved fuel container, out of the reach ...
Operation Manual - Page 8
... height levers forward. Allow the rope to return to the same height as desired. Lower the mower
Note: The cutting height settings are 1 inch (25 mm); 1-3/8 inches (35 mm); 1-3/4...mower
Figure 9 2. Blade control bar
Figure 10
2. Adjusting the Cutting Height
WARNING
Adjusting the cutting height may bring you . Adjust the cutting height as the rear wheels (Figure 9). Set the front wheels...
Operation Manual - Page 9
... moving parts to Removing the Side Discharge Chute) before recycling the clippings. Using the Self-propel Drive
To operate the self-propel drive, simply walk with your sides, and the mower will automatically keep pace with you want to collect grass and leaf clippings from the factory ready to disengage the wheel drive. Installing the Grass Bag
1.
Bagging the Clippings
Use...
Operation Manual - Page 11
... blade is in serious personal injury. Stop the engine and wait for cutting very tall grass.
contacting the blade can result in the bagging position, move the lever to the recycling position (refer to stop before leaving the operating position. If the grass bag is on the mower and the bag-on -Demand...
Operation Manual - Page 12
...leaves on your mowing speed if the mower does not cut the leaves finely enough. Set the cutting height on the...the cutting height on the lawn, set the front wheels at 2-1/8-inch (54 mm) and the rear wheels at a slower pace while mowing.
- Cut...blade when necessary with a Toro replacement blade. This helps disperse the clippings over any object.
• If the mower strikes an object or starts...
Operation Manual - Page 13
... of the machine from an Authorized Service Dealer (go to www.toro.com to stop.
2. Gasoline is flammable, explosive and can cause personal injury. If you must
13 Note: Replacement parts are available from the normal operating position. WARNING
Tipping the mower may cause the fuel to run dry through normal usage. replace...
Operation Manual - Page 14
...used oil out through 10 until the oil level on the dipstick (Figure 20). Move the mower to the operating position. 6. Refer to Preparing for the oil to drain the used oil properly... Note: If the oil level is at a local recycling center.
14 Important: Do not overfill the crankcase with oil and run the engine. Return the mower to a level surface. 2. Drain the excess oil until...
Operation Manual - Page 17
...
clippings go from rusting.
10. Wash out the area under the mower housing. • Wear eye protection. • Stay in both the fully forward and fully rearward positions. 4.
Adjusting the Self-propel Drive Cable
Whenever you have completed mowing. 1. Move the mower onto a flat paved surface. 3.
Stop the engine.
8. Tighten the nut on .
6.
ratchet or wrench and...
Operation Manual - Page 20
... cable/...Lawn Mowers...spring and late autumn
- if you are having difficulty starting procedures.
The Toro Total Coverage Guarantee
A 2-Year Full Warranty (45 Day Limited Warranty for Commercial Use)
The Toro GTS Starting Guarantee
A 3-Year Full Warranty (Not Applicable for Commercial Use)
22 in Recycler® 20 in Mulcher/Bagger
Walk Power Mowers
Conditions and Products Covered
The Toro...
Parts Catalog - Page 1
Original Instructions (EN)
Form No. 3371-846 Rev A
22in Recycler® Lawn Mower
Model No. 20332-Serial No. 312000001 and Up
Parts Catalog
Register at www.Toro.com.
Parts Catalog - Page 2
...: Liquid Propane NI: nylon insert NPTF: national pipe thread fine PFH: phillips flat head PPH: phillips pan head PPHTF: ... square head SRH: slotted round head STD: standard TAP: self tapping TTH: torx truss head
2 The n represents the quantity....
For example, a wheel assembly might be identified by reference number 6, the tire by 6:1, the valve by 6:2, and the wheel by reference numbers 6:1,6:2,...
Parts Catalog - Page 3
..., Side Chute and Rear Door Assembly 4 Rear Bag Assembly 5 Engine and Blade Assembly 6 Front Wheel and Height-of-Cut Assembly 7 Transmission and Rear Wheel Drive Assembly 8 Handle Assembly 9 Attachments and Accessories 10
© 2011-The Toro® Company
Contact us at www.Toro.com.
8111 Lyndale Avenue South Bloomington, MN 55420
3
Printed in the USA.
Parts Catalog - Page 6
...
7 108-9764-03 1 Blade-22 Inch
8 108-3766-03 1 Support-Blade
9 105-8579
1 Bolt-Blade
10 105-3030-03 1 Guide-Belt
11 95-1726
3 Screw-Taptite
12 114-7937
1 Cover-Belt
13 46-8091
2 Screw-HWH
14 2210-316
1 Stop-Rope
16 121-2371
1 Decal-Shroud
● Not serviced separately 3371-846A...
Parts Catalog - Page 7
...-03 2 Plate-HOC, Front
2 322-3
4 Screw-HH
3 3296-29
6 Nut-Lock, NI
4 105-1818
2 Bushing-Mount, HOC
5 105-1807
2 Arm-Pivot, Front
6 105-1809
2 Arm-Spring
7 110-0549
2 Knob-HOC
8 105-3048
2 Washer-Flat
9 322-6
2 Screw-HH
10 40-1940
2 Washer
11 614650
2 Bolt-Shoulder
12 115-2894
2 8 Inch...
Parts Catalog - Page 8
...-29
4 Nut-Lock, NI
5 108-9779
2 Retainer-Bushing, HOC
6 104-8699
2 Bearing-Ball
7 108-9782
2 Bushing-Sleeve
8 108-9781
2 Arm-Pivot, Rear
9 108-9780
2 Arm-Spring
10 110-0549
2 Knob-HOC
11 115-4652
1 Transmission
12 115-4669
1 Belt-V
13 114-7977-03 1 Bracket-Transmission
Ref. Transmission and Rear Wheel Drive Assembly
Ref.
Similar Questions
Toro Recycle Manual 20334 Self Propelled Does Not Work
(Posted by khamik 9 years ago)
Self Propelled Feature Stopped Working...
I own a 20332 purchased on 5/15/2010 at Jerrys Hdwe in Edina, MN. The self propelled feature stopped...
I own a 20332 purchased on 5/15/2010 at Jerrys Hdwe in Edina, MN. The self propelled feature stopped...
(Posted by cfuhrmann1 9 years ago)
Self Propel
How can i fix my self propel? It won't work but the cable pulls tight everything seems to work
How can i fix my self propel? It won't work but the cable pulls tight everything seems to work
(Posted by rjgrant13 10 years ago)
Toro Personal Pace Self-propel System Stopped Working How To Repair
(Posted by Renpinki 10 years ago)
Toro Recycler 22 Inch Wont Self Propelled
(Posted by nar3n8 10 years ago)