Singer 7463 Confidence Support Question
Singer 7463 Confidence Support Question
Find answers below for this question about Singer 7463 Confidence.Need a Singer 7463 Confidence manual? We have 1 online manual for this item!
Question posted by RobinMom12 on February 1st, 2023
Singer Confidence 7463 Support - Flashing Lights After All Checks.
When starting to sew, a beep sounds and all the lights begin flashing. I have done all the following checks: good needle, clean machine, everything replugged, rethreaded, bobbin spool in the right place, and correct thread and bobbin. Sometimes multiple tries and it will work randomly. The correct stitch length and needle position choice sometimes helps but not always.
Current Answers
Answer #1: Posted by SonuKumar on February 1st, 2023 6:45 PM
SonuKumar
Member since:
May 9th, 2021 Points: 16,638,170
Member since:
May 9th, 2021 Points: 16,638,170
If your Singer 7463 Confidence machine is flashing lights after you've done all the checks, it could indicate an issue with the machine's settings or hardware. To troubleshoot this problem, you can try the following steps:
- Unplug the machine and wait for a few minutes before plugging it back in.
- Check that the needle is properly inserted and tightened.
- Ensure that the presser foot is in the proper position.
- Make sure the bobbin is inserted correctly and the case is in place.
- Check for any tangled threads or other obstructions.
- If the flashing lights persist, you may need to refer to the Singer 7463 Confidence manual or contact Singer's customer service for further assistance.
If none of these steps resolve the issue, it may be necessary to have the machine serviced by a professional.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Answer #2: Posted by MercedesAMG on February 1st, 2023 3:46 PM
MercedesAMG
Member since:
January 26th, 2013 Points: 193,710
Member since:
January 26th, 2013 Points: 193,710
If you have checked all of these possible issues and the machine is still not functioning properly, it may be an issue with the machine's electrical or mechanical components. In this case, I would recommend contacting the Singer customer support for further assistance or taking the machine to a professional repair service.
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Singer 7463 Confidence Manual Pages
Instruction Manual - Page 3
...CONTENTS
1. KNOWING YOUR SEWING MACHINE Machine identification 6 - 7 Accessories 8 - 9 Setting up your machine 10 - 11 Spool pins 12 - 13 Presser foot lifter, Darning plate 12 - 13 Converting to free-arm sewing 12 - 13 Winding the bobbin 14 - 15 Threading the bobbin thread 16 - 17 Threading the top thread 18 - 19 Using automatic needle threader 20 - 21 Needle, thread and fabric chart...
Instruction Manual - Page 6
...Thread cutter 6. Handle 12. Cord socket 15. Automatic needle threader 19. Needle 23. Needle plate 31. Power line cord 33. Thread take-up 3. Face cover 5. Bobbin cover release button 32. KNOWING YOUR SEWING MACHINE
MACHINE IDENTIFICATION
1. Needle threader Thread Guide 20. Thread guide 21. Thread guide 2. Horizontal spool pin 11. Foot release button 27. Presser foot...
Instruction Manual - Page 8
... foot
The Foot that comes on your Sewing machine is another very useful foot and should be used for most of your decorative sewing.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Spool pin felt discs (2) 5. Spool pin cap (large) 8.
ACCESSORIES
1. Blind stitch foot 14. Bobbins (4 total - 1 in machine) 3. Needles 2. Zipper foot 12. Buttonhole opener/Seam Ripper...
Instruction Manual - Page 10
... "OFF". The same switch controls both the power and the light.
When servicing the machine, or changing needles, etc., machine must be disconnected from the wall-outlet. Connect the foot control plug (3) into the cord socket (1) and your machine the first time. Always disconnect the machine from power supply by removing the plug from the power...
Instruction Manual - Page 12
... SEWING
Your machine can be used . bed or as a standard flat-bed model. Place a spool of thread. Select the correct spool pin cap according to the type and diameter of needle plate. With the extension table removed the machine converts into place until it firmly with the two pins on the spool pin. SPOOL PINS
HORIZONTAL SPOOL PIN for normal thread spools
Place...
Instruction Manual - Page 16
... the thread
along the groove on the needle plate until it is pulled.
4. Bobbin cover will pop up the bobbin thread.
6. The bobbin must rotate counterclockwise when thread is snipped with
cutter on top of the bobbin, pull the
5
thread until it stops in the slot (B). NOTE: Sewing can be started without picking up sufficiently to
2
allow...
Instruction Manual - Page 18
...take-up (4) from right to left.
4
* Pull the thread into the inside of the take-up lever until the needle is in the tension discs, do this simple check:
1.) With the presser... firmly gripping the thread with your right hand in the
following page for instructions on operation of the Automatic Needle Threader.)
IMPORTANT:
To verify that the machine is not raised, correct thread tension...
Instruction Manual - Page 22
... not use on stretch fabrics. * For best sewing results, always use the same size and type of thread in the bobbin as examples of weight. Insert the new needle into the needle plate slot.
22
Flat side toward you .
2.
The following table is a practical guide to use a Singer Branded Needle.
NEEDLE, THREAD AND FABRIC CHART
Your fabric will...
Instruction Manual - Page 24
... If, when you start to adjust the tension control.
You will always obtain a nicer stitch and less puckering when the upper thread appears on top of the machine. Push presser foot ... PRESSER FOOT
Be sure needle is usually only desireable for straight stitch sewing. ADJUSTING TOP THREAD TENSION
90% of your sewing will be less than for straight stitch sewing. Place the desired foot on ...
Instruction Manual - Page 26
... width/needle position controls
Your sewing machine will produce most of determining available adjustments is to locate each manual adjustment point, the LED will blink 3 times and a beep will be lit.
Notes: 1. Auto (preprogrammed) default settings are contained in the "Other Information" Section.
Stop when the LED indicator above the straight stitch pattern will sound...
Instruction Manual - Page 28
... carried out while the reverse stitch switch is very useful for tie-off of sewing.
28 The machine will be at the start and end of other stitches The sewing machine makes 4 tiny tacking stitches to avoid raveling at the exact spot in reverse as long as the reverse switch button is pushed. The position...
Instruction Manual - Page 32
... as an aid for all types of sewing.
1
Let's begin by following the steps below.
1. The numbers indicate distance from the needle at the start and end of the seam. STRAIGHT STITCHING
A
Straight stitch is at its center position. C
A. Presser foot lifter D. Start the machine.
The guide line on the needle plate. General Purpose Foot
D
Thread tension control...
Instruction Manual - Page 34
... or lightweight thread that the needle passes through the opening on the right side of the foot.
This thread should not show. 3. Start to sew. INSERTING ZIPPERS AND PIPING
Use zipper foot to sew to the right or left of fabric.
Thread bobbin with different tension and stitch length combinations.
34
Thread machine with the Stitch Width Control...
Instruction Manual - Page 36
... width is selected.
Note: When sewing a dense (closely spaced) Satin Stitch, the Satin Stitch Foot MUST be used. ZIGZAG STITCHING
SETTINGS :Presser foot -
The light grey boxes indicate all the possible ..., type of stitch and sewing speed, but the bobbin thread must never appear on the sewing machine. SATIN STITCH
This is pulling to the top or you are actual sewing lengths and widths and do...
Instruction Manual - Page 38
.... When completed, the stitching is primarily used . Place the fabric under the foot. The stitch width control changes the swing of the needle for normal firm fabrics
- Regular blind stitch for ...STITCH
The blindhem stitch is almost invisible on the right side of the fabric. On fine fabric turn up .
1
2
Medium to sew blind hems. Always make a sewing test first.
4
Top side Cara Endroit
38 ...
Instruction Manual - Page 48
... operation.
DOUBLE OVERLOCK STITCH
The Double overlock stitch has three main uses. It is most often sewn with a Wing Needle (Singer Style 2040) to create holes in heirloom sewing. CROSSED STITCH
Use to sew and finish elastic fabrics or for decoration of borders.
48
It is primarily used on borders and for use in...
Instruction Manual - Page 50
...* Before starting to sew, check that the thread will not run out during sewing.
* Slightly...places which can also be used as a decorative stitch, it can easily unravel. Satin stitch foot :Thread tension control - When using this .
AUTO
* Always practice on lapel In addition to using this time.
Sew...bobbin to cut the stitch at this stitch pattern for table linen edges, first sew...
Instruction Manual - Page 60
... ensure the best possible operation of sewing machine oil on the needle plate (1) and slide the needle plate toward you as indicated by removing the plug from the wall-outlet. CARING FOR YOUR MACHINE
CLEANING HOOK AREA AND FEED DOGS
1
Always disconnect the machine from power
supply by the arrows. (A, B)
NOTE: Singer Brand Sewing Machine Oil is not suited for...
Instruction Manual - Page 62
... recommended. TWIN NEEDLE (Option)
A twin-needle produces two rows of thread. Place a spool on each needle from front to your machine.
This will result in broken needles and possible damage to back.
2. Slightly loosen top thread tension for appliqueing and bar tacking. NOTE: Needle threader cannot be set beyond a twin needle mark, regardless of a Singer Brand 3mm (Style...
Instruction Manual - Page 68
... a damaged needle plate as threading needle, changing needle, threading bobbin, or changing presser foot, etc." 15. "DANGER--To reduce the risk of The Singer Company Ltd or its intended use , or equivalent." Use only attachments recommended by pulling on cord. "Do not use bent needles." 13. "Never sew with this manual." 3. "Switch the sewing machine off
before cleaning."
2. This...
Similar Questions
Singer7470 Making A Beeping Sound And Not Working
hi my singer 7470 which i just recieved is making a beeping sound every time i press the pedal and i...
hi my singer 7470 which i just recieved is making a beeping sound every time i press the pedal and i...
(Posted by jamespyper 3 years ago)
How Do I Adjust The Stitch Length
I need a longer stitch length. the stitches are so short they are causing the material to bunch up. ...
I need a longer stitch length. the stitches are so short they are causing the material to bunch up. ...
(Posted by loripursey 3 years ago)
Bobbin Not Winding - 7463 Confidence
I have a brand new machine and following the instructions I have been trying to wind a bobbin, but t...
I have a brand new machine and following the instructions I have been trying to wind a bobbin, but t...
(Posted by advirasp 9 years ago)
Stitch Length Control
is the stitch length control a variable resistor , if so , how can it be accessed in order to replac...
is the stitch length control a variable resistor , if so , how can it be accessed in order to replac...
(Posted by tonysmith47 9 years ago)
Lights Flashing
All The Indicator Lights Are Flashing At Once. Machine Will Not Sew.
All The Indicator Lights Are Flashing At Once. Machine Will Not Sew.
(Posted by Anonymous-114574 10 years ago)