Ryobi TS1342L Support Question

Find answers below for this question about Ryobi TS1342L.
Need a Ryobi TS1342L manual? We have 4 online manuals for this item!

Ryobi Overview Questions Manuals Reviews Videos Research

Question posted by sjshhs on January 10th, 2014

Replace Saw Blade

How To Remove And Replace The Saw Blade

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by waelsaidani1 on January 10th, 2014 8:55 PM

This answer was accepted by the poster of the original question.

waelsaidani1

Member since:
May 12th, 2013

Points: 19,501,797

1,100
points

Hello follow the guide here on how to replace saw blade http://homeguides.sfgate.com/replace-blade-ryobi-10-inch-power-miter-saw-model-ts254-75950.html

Related Ryobi TS1342L Manual Pages

English Manual - Page 3

... ELECTRICAL SHOCK by removing starter keys.  DON'T FORCE THE TOOL. Keep tools sharp and clean for lubricating and changing accessories.  DISCONNECT TOOLS. Serious injury could ignite fumes. Check for use power tools in doubt, use , before turning it on the tool while it will draw. Sharp blades minimize stalling and kickback.  Blade coasts after being...

English Manual - Page 4

...TOOL dry, clean, and free from catching the loose end and kicking up to full speed before connecting to be cut more than one workpiece on the same side of your saw from oil and grease. Have defective switches replaced by a qualified service technician at a time. Inspect for and remove... If repair or replacement of blade pinching and kickback. Repair or replace a damaged or worn...

English Manual - Page 5

... off tool and wait for saw blade to stop before moving workpiece or changing settings.  THIS TOOL should break, bend, or fail in or near the cutting path of the blade.  NEVER move into the blade. f) Turn off the power switch, remove the miter saw is missing or should have damaged, missing, or failed parts replaced before...

English Manual - Page 9

...the blade. FPM or SPM Feet per minute (or strokes per minute), used to feed the workpiece through the thickness of the workpiece. Kerf The material removed by the blade in...blade to the workpiece, that area which a blade or cutting tool is mounted. Resin A sticky, sap-based substance that can occur when the blade binds or stalls, throwing the workpiece back toward the front of the saw blade...

English Manual - Page 11

... . Use the hex key end when installing or removing blade and the phillips end when removing or loosening screws. MITER FENCE The miter fence on each side of the project you are for the blade wrench is included with the saw arm. Located on the compound miter saw . It is being made with all ball bearings...

English Manual - Page 12

...TOOLS NEEDED The following tools (not included) are needed for making adjustments or installing the blade...blade. Store the padlock key in the off position. The miter lock handle securely locks the saw , disconnect it from rotating. It retracts over the upper blade guard as the saw is lowered into the workpiece. Depress and hold the lock button while installing, changing, or removing blade...

English Manual - Page 13

...discard the packing material until you have carefully inspected and satisfactorily operated the tool.  The saw arm by the handle. LOOSE PARTS The following items are damaged or ...61550; This saw has been shipped with the tool:  Miter Lock Handle  Dust Bag  Work Clamp DUST BAG  Blade Wrench  Operator's Manual MITER LOCK HANDLE BLADE WRENCH WORK ...

English Manual - Page 14

... the missing parts are replaced. WARNING: Do not start the compound miter saw should be of sufficient length to a firm supporting surface such as a workbench. The compound miter saw without checking for this ...to heed this warning could result in the saw is not secured to the blade if it strikes the miter fence during use with this tool. Failure to heed this warning can result ...

English Manual - Page 15

.... 8 Fig. 9 Base 15 Work Clamp Fig. 10 The work clamp to the fence or the saw blade. This is provided for emptying, simply reverse the above procedure. WARNING: In some operations, the work ... the size of the workpiece, it on the upper blade guard. Depending on the end of the work clamp in serious personal injury. To remove the dust bag for use a C-clamp instead of ...

English Manual - Page 16

... left hand threads. Spindle Lock Button WARNING: If inner blade washer has been removed, replace it before reconnecting saw . Fig. 11 16 Never engage spindle lock button when blade is not engaged before placing blade on the spindle.  Depress spindle lock button and replace blade bolt. Installing / replacing the Blade See Figures 11 - 12. Failure to do so can...

English Manual - Page 17

...cutting. hd) LASER GUIDE Blade SCREW Blade Blade BOLT cover Inner Blade Washer Lower blade guard To LOOSEN To Tighten blade BOLT (hex. ASSEMBLY Danger: Laser radiation. NOTE: As the saw blade in the uppermost position,... on Spindle Fig. 12 "NO HANDS ZONE" LABEL BROKEN LINE Fig. 13 17 To Remove Your Mark:  Position the laser line near the right edge of material. NEVER ...

English Manual - Page 19

... transport position.  Loosen the miter lock handle approximately one-half turn.  Depress the miter lock plate and rotate the miter table until the saw blade is positioned at 0°.  Release the miter lock plate and securely tighten the miter lock handle.  Lay a framing square flat on the miter...

English Manual - Page 20

...; to zero. Note: The above procedure can be parallel as shown in figure 22.  If the top or bottom of the saw blade to check blade squareness of the saw blade angles away from the square as shown in figures 23 and 24, adjustments are needed.  Loosen the lock nut securing positive stop...

English Manual - Page 22

... arm until the pointer aligns with one edge securely against the fence. Wait until the pointer aligns with the saw blade.  Grasp the stock firmly with the blade angled to stop rotating before removing the workpiece from the miter table. Note: Quickly locate zero by releasing the lock plate as you rotate the...

English Manual - Page 23

..., located in scrap material before removing the workpiece from turning before making compound miter setups due to the correct angle and the saw table. Compound Miter Cut WORK CLAMP Fig. 28  Tighten the miter lock handle securely.  Loosen the bevel lock knob and move the saw blade to its full height. ...

English Manual - Page 24

... to stop rotating before removing the workpiece from miter table. Long workpieces need extra supports. Wait until the electric brake stops blade from turning before raising the blade out of the cutting ... seconds for the blade to reach maximum speed.  Slowly lower the blade into and through the workpiece.  Release the switch trigger and allow the saw blade to SUPPORT LONG ...

English Manual - Page 28

...not start the compound miter saw blade to the miter table at the factory and normally do not require readjustment. blade provided with blade provided should rise completely to ... stop limits the blade's downward travel. ADJUSTMENTS WARNING: Before performing any readjustments that are necessary and periodically check the parts alignment to make sure the tool is unplugged from ...

English Manual - Page 29

...may result in accidental starting causing serious injury.  Remove brush cap with side shields during power tool operation or when blowing dust. Therefore, no further lubrication ... highly abrasive to remove dirt, dust, oil, grease, etc. Brush assembly is required:  Unplug the saw could result in serious personal injury. Proceed as follows when replacement is spring loaded ...

English Manual - Page 30

.... ductive device such as a toothpick. Do not attempt to laser guide support using a non-con- MAINTENANCE Changing the Batteries See Figure 37.  Unplug the saw.  Remove the laser guide from the saw .  After cleaning the laser guide and replacing the batteries, secure the laser guide cover to activate the laser.

English Manual - Page 32

...activities contains chemicals known to these exposures varies, depending on how often you do this tool will be found on a plate attached to filter out microscopic particles. • SERVICE... and serial number in . Your risk from chemically-treated lumber. AND SERIAL NO. Compound Miter Saw TS1342L - OPERATOR'S MANUAL 10 in the space provided below. • HOW TO ORDER REPAIR PARTS ...