Ryobi RTS31 Support Question
Ryobi RTS31 Support Question
Find answers below for this question about Ryobi RTS31.Need a Ryobi RTS31 manual? We have 4 online manuals for this item!
Question posted by christianburger on February 9th, 2015
Out Feed Support Fence
the out feed support fence will not extend. what could be stopping it. it is free on the miter side but will not move in the middle and the side that extends for wider pieces.
Current Answers
Answer #1: Posted by hzplj9 on February 10th, 2015 11:25 AM
hzplj9
Member since:
June 25th, 2012 Points: 4,873,510
Member since:
June 25th, 2012 Points: 4,873,510
In the user guide are instructions for extending the table. There appears to be a lever at the front to the left of the handle. If you download the user guide from the Manual Owl link:
http://www.helpowl.com/manuals/ryobi-rts31-user-manual-d939d50.pdf
Refer to page 30 of the manual it describes the procedure. If it still will not move then take alook at the underside to see if a piece of timber has lodged itself in the runners.
Hope that helps.
Related Ryobi RTS31 Manual Pages
User Manual - Page 3
... of checking to see that may risk injury.
NEVER STAND ON TOOL. A guard or other conditions that keys and adjusting wrenches are intended for . Feed work area well lit.
KEEP CHILDREN AND VISITORS AWAY. Wear hearing protection during extended periods of improper accessories may affect its intended function. Keep hands away...
User Manual - Page 4
...; SUPPORT LARGE PANELS.
GENERAL SAFETY RULES
work firmly against the rip fence or miter fence. Do not attempt to do not come within 3 in this manual or addendums. Use of cord location and keep it will not fit the outlet, have the proper outlet installed by a qualified electrician. Keep TOOL dry, clean, and free from...
User Manual - Page 5
...Miter fence AND RIP FENCE during the same operation.
NEVER use rip fence as cutoff gauge when cross cutting.
NEVER attempt to free a stalled saw blade without first turning the saw OFF and disconnecting the saw from the power source.
PROVIDE ADEQUATE SUPPORT... Never cut more than one piece of your body in this tool, loan them frequently and use of accessories...
User Manual - Page 8
...installed and maintained, is designed to stop the workpiece from being kicked back ...extends completely through the thickness of the saw during any angle to feed the workpiece through cut by a fence, miter fence... of the blade to make thinner pieces. Cross Cut A cutting or shaping...substance that area which a blade or cutting tool is not properly supported. Saw Blade Path The area over the...
User Manual - Page 10
... front rail, the easy-to heed this product requires an understanding of the information on the tool and in a location that is a hazard in which helps keep the blade guard down "... metal piece of the blade guard assembly, slightly thinner than the speed of kickback. Place the key in this table extension gives the operator additional support when cutting wide workpieces. MITER FENCE WITH ...
User Manual - Page 11
... the blade. Warning:
To reduce the risk of accidental starting when power returns.
With the miter fence removed, the miter table offers additional support for other operations such as ripping.
This action will prevent the tool from the switch and store in a safe, secure location. WARNING:
ALWAYS make sure the switch is not in use...
User Manual - Page 22
...kickback pawls may contact the blade.
Improper connection of this tool. Have the correct outlet installed by 1/8 in this ...accessories not recommended can cause serious injury. Use the miter fence when cross cutting. APPLICATIONS
You may use any attachments... knots with dull blades.
To avoid pinching the blade, support the work Forcing a cut Cutting warped or ...
User Manual - Page 24
...the workpiece securely against the rip fence. Bevel cross cuts are across the... miter cut . Always provide proper support for the wood as it comes
out of this tool....wider than the speed of this operator's manual before attempting any loose knots with making cross cuts, rip cuts, bevel cuts, and miter...or bevel) miter cuts are straight 90° cuts made with small pieces of cuts
See ...
User Manual - Page 28
... be perpendicular to the rear of the blade.
If a gap exists, the miter fence may want to set it at 0°.
See To Adjust the Quick Stop in place with adjusting clamp (J). The miter fence must be out of the blade, the miter table needs aligning. Follow the adjustment procedures that follow. NOTE: The quick...
User Manual - Page 32
... place by twisting the lock knob clockwise.
WARNING:
Do not use . Failure to heed this tool. Use the miter fence when making a cross cut operations.
operation
MAKING CUTS
The blade provided with both hands on the miter fence and feed the workpiece into the blade. Hold the workpiece firmly with the saw is made, turn...
User Manual - Page 33
... for the blade to come to guide it.
operation
making a miter cut
See Figure 44. If ripping a narrow piece, use the hand closest to the rip fence to a complete stop before feeding the workpiece into the blade. Wait for the workpiece.
Set the miter fence to the desired angle and tighten the lock knob.
Make...
User Manual - Page 35
... feeding the workpiece into the blade. Once the blade has made , turn the saw off . operation
When ripping a long workpiece, place a support the...miter
fence and feed the workpiece into the blade. Hold the workpiece firmly with the workpiece, use a push stick and/or push blocks to a complete stop before removing the workpiece. making a compound (bevel) miter...
User Manual - Page 36
....
Add supports to the sides as rabbets or dadoes. Read the appropriate section which describes the type of cut such as needed.
Depending on the shape of the panel, use either
the rip fence or miter fence. Plug the saw into the blade. Use a push stick to move the piece through cut...
User Manual - Page 37
... making dado cuts to a complete stop before you turn the saw off....tool. All blades and dado sets must not be used provided the arbor shaft extends slightly beyond the arbor nut.
Make sure the blade nut is fully engaged and the arbor extends past the blade.
Never push a small piece...feeding the workpiece into the blade with the edge flush against the rip fence or miter fence...
User Manual - Page 40
... turn the framing square 180° to check the other side. If the two dimensions are made, these adjustments may cause the quick stop against the miter fence with miter scale set at 0°. Adjust eccentric screw until it . Retighten the two screws. Make two or three test cuts on...
User Manual - Page 42
.... Resharpen or set .
Adjust positive stops.
Change blade; Wood edges away from rip fence when ripping. Saw does not start.
Rip fence is tripped. Miter base or slides improperly adjusted. Circuit...when turning height/bevel adjusting handwheel. Replace or sharpen blade. Slow the feed rate. Align the rip fence. Wood is dull. Always cut .
Move locking lever down position.
...
User Manual - Page 44
... calling 1-800-525-2579.
• How to obtain Customer or Technical Support:
To obtain Customer or Technical Support please contact us at one of California to cause cancer, birth defects, or...based paints, • crystalline silica from bricks and cement and other reproductive harm. Table Saw
RTS31
WARNING:
This product and some dust created by power sanding, sawing, grinding, drilling, and ...
User Manual 4 - Page 3
...RTS31... TABLE SAW or when ordering parts. NUMBER
DESCRIPTION
QTY
1 089037012001 Table 1
24 089037011020 Out Feed Support Holder 2
2 089037012002 Screw (M6 x 25 mm, Pan Hd 6
25 089037012010 Screw (M4... Hd 7
9 0134010911 Miter Table Latch 1
32 089037012013 Screw (M6 x 30 mm, Hex Hd 6
10 089037012005 Miter Table Latch Guide 1
33 089037012014 Rear Rail Support 3
11 410171721
Screw ...
User Manual 4 - Page 4
... Push Stick 1
089037007007 Screw (M4, Pan Hd 2
089037012028 Miter Table 1
0134010309 Positioning Plate 1
410181001
Screw (M4 x 7...RYOBI 10 in ., Pan Hd 2
67 0134010322-58 Outfeed Support 1
68 089037011019 Outfeed Support Rod 2
69 410192001
Screw (M4 x 10 mm 2
70... Stop 2
0134010802 Lock Nut 2
9134015330201 Pinch Point Label 1
KEY PART
NO. MODEL NUMBER RTS31
The ...
User Manual 4 - Page 9
...62-67 1
9
PARTS LIST FOR FIGURE C
KEY PART
NO. Hd 2 Bevel Moving Block 1 Screw (M5 x 12 mm, Pan Hd 2 Support Bracket 1
49 410291004
Screw w/Washer (M6 x 10 mm, Hex Hd.)......... 2
50 089037012048 Bolt (M6 x 80 mm, Hex Hd 1
51 0134010503... (M6 x 12 mm, Hex Soc. RYOBI 10 in. TABLE SAW - MODEL NUMBER RTS31
The model number will be found on a label attached to the cabinet.
Similar Questions
Nesecito El Rip Fence De La Sierra Ryobi Rts 31
Hola mi no.bre es Mauricio Hidalgo y les escribo desde chile .mi problema es que Compre una sierra r...
Hola mi no.bre es Mauricio Hidalgo y les escribo desde chile .mi problema es que Compre una sierra r...
(Posted by Mh74 5 years ago)
Compatibilidad Rts 31 Con Rts 21
1.el rip fence o tope lateral del modelo RTS 31 es igual al del modelo RTS 21
1.el rip fence o tope lateral del modelo RTS 31 es igual al del modelo RTS 21
(Posted by Sepu 6 years ago)
I Have To Remove Arm Support Bracket To Replace It After A Falling Accident
dear sirs I removed two little nuts and am stocked with lock pins , so what tool do you use to remov...
dear sirs I removed two little nuts and am stocked with lock pins , so what tool do you use to remov...
(Posted by thguenand 8 years ago)
Support Arm
The support arm (part number 080009002037) on mine broke. It appears as though this part has been di...
The support arm (part number 080009002037) on mine broke. It appears as though this part has been di...
(Posted by stephanieyatuni 10 years ago)