Ridgid RP 330-C Support Question
Ridgid RP 330-C Support Question
Find answers below for this question about Ridgid RP 330-C.Need a Ridgid RP 330-C manual? We have 1 online manual for this item!
Question posted by remont on September 12th, 2013
Rp 330-c Manual
The person who posted this question about this Ridgid product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by TommyKervz on September 12th, 2013 11:32 PM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,803
Member since:
January 10th, 2013 Points: 17,776,803
Greetings - Go here http://www.helpowl.com/manuals/Ridgid/RP330C/182503
Related Ridgid RP 330-C Manual Pages
Owners Manual - Page 1
RP 330 Manual
Pressing Tool
WARNING! Failure to understand and follow the contents of this tool. Read this Operator's Manual carefully before using this manual may result in electrical shock, fire and/or serious personal injury.
• Français - 13 • Castellano - pág. 27
Owners Manual - Page 2
RP 330 Pressing Tool
Table of Contents
Recording Form for Machine Serial Number ...1 General Power Tool Safety Information
Work Area Safety...2 Electrical Safety ...2 Personal Safety ...3 Power Tool Use and Care ...3 Battery Tool Use and Care ...3 Service ...3 Specific Safety Information Pressing Tool Safety ...4 Battery and Charger Safety ...4 Description and Specifications Description ...4 ...
Owners Manual - Page 3
Serial No. RP 330
Pressing Tool
RP 330-B Battery Tool
RP 330-C Corded Tool
RP 330 Pressing Tool
Record Serial Number below and retain product serial number which is located on nameplate.
Owners Manual - Page 4
... or fumes.
• Keep children and by-standers away while operating a power tool. Distractions can cause you to the protection of property. Do not use a ground fault circuit interrupter (GFCI) protected supply.
RP 330 Pressing Tool
Safety Symbols
In this operator's manual and on the safe and proper operation of the equipment. Use of a cord...
Owners Manual - Page 5
... to be ejected from those intended could result in the off-position before use a power tool while you are easier to operate the power tool. avoid contact. Use of the power tool may cause irritation or burns. RP 330 Pressing Tool
Personal Safety
• Stay alert, watch what you are connected and properly used. Use the...
Owners Manual - Page 6
... has been dropped or damaged in damp or wet environment.
Other uses or modifying the RP 330 Pressing Tool for RP 330-B only)
WARNING Read the battery charger manual before using the charger or batteries. Pressing Tool Safety
• Use the RP 330 Pressing Tool only with a new jaw set instructions, the fitting manufacturer's installation instructions and the instructions for...
Owners Manual - Page 7
... and service temperature, should be completed. Ridge Tool Company
5 RP 330 Pressing Tool and Standard Series Jaw Set
Specifications
RP 330-C Corded Pressing Tool: Motor
Voltage 120V, Single Phase AC 60 ....
3. If a corded tool, inspect the power cord and plug for damage or modifications. Before any problems to the compact tool's operator's manuals for selection information.
Jaw Arm...
Owners Manual - Page 8
... cause sparks. • Clear, level, stable dry place for an application can distract the tool operator during use the tool until sources have been inspected as shown in Figure 5 and fully close the attachment mounting pin. RP 330 Pressing Tool
4. Pressing Tool Warning Label
Figure 3 - Label On Bottom Of Battery 6. If any other causes, and prevent...
Owners Manual - Page 9
..., as specified in the appropriate fitting system's operator's manual. Ridge Tool Company
7 If using a battery tool, with the contour of injury from the tool
attachment during the press cycle. Follow operating instructions to hang the jaw set installed.
2. For the RP 330-B, insert fully charged battery into the tool. Do not attempt to reduce the risk of...
Owners Manual - Page 10
... has begun. Press jaw arms to fitting system's operator's manual.
Pressing A Fitting With Typical Actuator And Press Ring Set
1. For the RP 330-B, insert fully charged battery into an appropriate outlet.
3. For the RP 330-C plug the tool into the base of the handle. To restart tool, it is necessary to press. Open the appropriate press ring...
Owners Manual - Page 11
... indicated by the fitting manufacturer, remove it. See press system's operator's manual for specific inspection criteria. RP 330 Pressing Tool
point injuries, keep fingers away from fitting by manually grasping ring halves and opening assembly.
Installing Press Ring Onto Fitting
Figure 10 - The tool will turn off automatically if the battery is not maintained within 2,000...
Owners Manual - Page 12
... have been designed to operate.
So it is out of reach of children and people unfamiliar with the RP 330 Pressing Tools. Inspect the attachment mounting pin and lubricate the pin with the RP 330, such as those listed below. Attachments should open and close freely with a clean dry cloth.
2. Required Maintenance at (800) 5193456...
Owners Manual - Page 13
... to the fully closed . Make sure the jaw contour is aligned with new fitting and new tube. RP 330 Pressing Tool
Troubleshooting
SYMPTOM
POSSIBLE REASONS
SOLUTION
Tool will not begin press cycle when trigger switch is depressed.
Bring tool and battery to correct operating range between 15°F (-10°C) to 122°F (50°...
Owners Manual - Page 14
... 50°C (122°F). Out of acceptable voltage range - Machine is locked - Service indicator after 32,000 cycles.
RP 330 Pressing Tool
RP 330 Diagnostic Codes
LED
Green
Status
Glows Blinks
Red Yellow
Blinks Glows
Blinks Glows
Description
Tool ON. Out of temperature range -10°C (15°F) to a reliable voltage supply. Service after 32,000...
Similar Questions
How Do I Add Hydraulic Fluid To The Ridged Rp 200 B
how do i add hydraulic fluid to the ridged rp 200 b
how do i add hydraulic fluid to the ridged rp 200 b
(Posted by tkennedy12968 2 years ago)
Rp-210 Crimper Tool
how can we order a replacement motor for the tool. the end has come off part way and the tool in una...
how can we order a replacement motor for the tool. the end has come off part way and the tool in una...
(Posted by webb97907 8 years ago)
Rigid Spindle Sander Manual Changing The Belt To A Simple Spindle Sander.
Can't seem to locate my manual and want to change the belt configuration to a simple single spindle ...
Can't seem to locate my manual and want to change the belt configuration to a simple single spindle ...
(Posted by evace109 8 years ago)
Shop Repair Manual
Am looking for a shop/repair manual (not the owner manual) for a Ridgid R4331 bench top planer.
Am looking for a shop/repair manual (not the owner manual) for a Ridgid R4331 bench top planer.
(Posted by jimshoe52 8 years ago)