Ridgid R5013 Support Question
Ridgid R5013 Support Question
Find answers below for this question about Ridgid R5013.Need a Ridgid R5013 manual? We have 1 online manual for this item!
Current Answers
Related Ridgid R5013 Manual Pages
Owners Manual - Page 1
... will give you for dependability, ease of injury, the user must read and understand the operator's manual before using this product. OPERATOR'S MANUAL
1/2 in. HAMMER DRILL
DOUBLE INSULATED R5013
Your hammer drill has been engineered and manufactured to our high standard for buying...
Owners Manual - Page 3
...making any adjusting key or wrench before use. Ensure the switch is dangerous and must match the outlet. Properly maintained cutting tools with the switch is in the off . Distractions can reduce dust-related... edges or moving parts.
If devices are provided for outdoor use the power tool if the switch does not turn it was designed.
Do not use . Safety equipment such as...
Owners Manual - Page 4
...when performing an operation where the cutting tool may contact hidden wiring or its applications and limitations, as ...well as those dust masks that may affect its intended function. WARNING:
Some dust created by a qualified repair person using this tool. To reduce your exposure to these instructions also. Contact with impact drills...
Owners Manual - Page 5
...
Minutes
Time
Alternating Current
Type of current
Direct Current
no
No Load Speed
Type or a characteristic of current Rotational speed, at no load
Class II Tool
Double-insulated construction
.../min
Per Minute
Revolutions, strokes, surface speed, orbits etc., per minute
Wet Conditions Alert
Do not expose to keep your hands away...
Owners Manual - Page 6
... do not use over eyeglasses or standard safety glasses with this product. Call RIDGID customer service for repair. We recommend Wide Vision Safety Mask for use this ...
SYMBOLS
The following signal words and meanings are intended to explain the levels of any power tool can result in foreign objects being thrown into your nearest AUTHORIZED SERVICE CENTER for assistance. SYMBOL...
Owners Manual - Page 7
... loss of the system and should be connected to your nearest authorized service center for loose or exposed wires and cut or worn insulation.
**Ampere rating (on tool data plate) 0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length
Wire Size (A.W.G.)
25' 16
16 16 16 14
14
50' 16
16 16 14 14
12
100' 16...
Owners Manual - Page 8
...
Chuck Capacity 1/2 in. Input 120 V, 60 Hz, AC only, 7.5 A Switch Variable Speed
Hammer Speed 0-51,000 BPM No Load Speed 0-2,700 r/min. (RPM) Net Weight 5 lbs.
DEPTH STOP ROD
DRILLING/HAMMER MODE SELECTOR
CHUCK
LOCK-ON BUTTON
CHUCK KEY STRAP
AUXILIARY HANDLE
ASSEMBLY
SWITCH TRIGGER
DIRECTION OF ROTATION SELECTOR (FORWARD/REVERSE)
P0WER CORD...
Owners Manual - Page 9
... Per Minute is equipped with all items listed in a hazardous condition leading to easily identify live tools. DIRECTION OF ROTATION SELECTOR
(FORWARD/REVERSE) Your drill has a direction of rotation (forward/reverse) selector located above the switch trigger for use , the chuck key can be placed in accidental starting and possible serious personal injury...
Owners Manual - Page 10
.../REVERSE)
Fig. 3
CAUTION:
To prevent gear damage, always allow familiarity with products to make you careless. WARNING:
Do not use . To turn the drill ON, depress the switch trigger.
LOCK-ON BUTTON
WARNING:
Always wear safety goggles or safety glasses with decreased trigger pressure. Do not be positioned to become overheated. Running...
Owners Manual - Page 11
... CHUCK JAWS CHUCK
RIGHT
Fig. 4
WRONG
Fig. 5
11 Also, raise the front of the chuck jaws.
OPERATION
TO INSTALL BITS
See Figures 4 - 5 Unplug the drill. Insert the chuck key and twist counterclockwise. Open or close the chuck jaws to a point where the opening
is slightly larger than the...
Owners Manual - Page 12
... use.
NOTE: When properly installed, the teeth on the depth stop rod should be mounted on the depth stop rod at the desired depth of drilled holes. Adjust the depth stop rod installed, the desired hole depth has been reached when the end of the rod comes in the auxiliary handle...
Owners Manual - Page 13
..., etc., in hard materials such as brick, tile, concrete, etc.
HAMMER MODE
DRILLING MODE
DRILLING/HAMMER MODE SELECTOR
LOCK-ON BUTTON
Fig. 8
SWITCH TRIGGER
Fig. 9
13 Use carbide-tipped bits and select hammer mode when drilling in soft materials.
Select normal drill mode when drilling with a lock-on feature immediately. To lock-on:
Depress the...
Owners Manual - Page 14
... control can result in the workpiece or if the drill stalls, stop the tool immediately. Let the tool do the work.
OPERATION
WARNING:
Before connecting the drill to a power supply source, always check to be drilled.�
Depress the switch trigger to start the drill.
Move the drill bit into the workpiece, applying only enough pressure...
Owners Manual - Page 15
..., lubricate the bit with side shields during power tool operation or when blowing dust. Begin drilling at a very low speed to prevent the bit...RIDGID replacement parts.
However, if you do not recommended using solvents when cleaning plastic parts. WARNING:
Always wear safety goggles or safety glasses with oil to improve drilling action and increase bit life. OPERATION
METAL DRILLING...
Owners Manual - Page 16
...This will tighten the chuck on the spindle. Tap sharply with a screwdriver.
To tighten:
Unplug the drill.
Open the chuck jaws.
Insert the hex key into the chuck and tighten the chuck ... It can now be removed and replaced with a new one.
Unplug the drill.
Open chuck jaws using the provided chuck key.
Insert a 5/16 inch or larger hex...
Owners Manual - Page 17
.... WHAT IS COVERED UNDER THE 3 YEAR LIMITED SERVICE WARRANTY
This warranty on RIDGID® Hand Held and Stationary Power Tools covers all original equipment packaged with the tool such as brushes, chucks, motors, switches, cords, gears and even cordless batteries in to the original purchaser at (toll free) 1-866-539-1710.
90-DAY SATISFACTION...
Owners Manual - Page 18
... us online at www.ridgid.com. For the location of this tool is found on a plate attached to provide all relevant information when you , please call or visit. When ordering repair parts, always give the following information:
Model No. Be sure to the motor housing. HAMMER DRILL
DOUBLE INSULATED R5013
Customer Service Information:
For...
Similar Questions
Wiring The Switch For R4020 Wet Saw
wire position for switch for Ridgid tile saw R402
wire position for switch for Ridgid tile saw R402
(Posted by jmck0924 1 year ago)
R5013 Wiring Diagram For Trigger Switch
Is there a wiring diagram somewhere that shows proper wire connections for the trigger switch.Thank ...
Is there a wiring diagram somewhere that shows proper wire connections for the trigger switch.Thank ...
(Posted by Robpotter 3 years ago)
Is There A Wiring Diagram For The R4510 Switch Actuator?
I have connect Ted the 4 wires but keep tripping the breaker. Must have one wire wrong and through o...
I have connect Ted the 4 wires but keep tripping the breaker. Must have one wire wrong and through o...
(Posted by djzinnicker 3 years ago)
Does Anyone Know How To Wire A New Switch To The R4513 Table Saw?
My saw has 5 wires coming out of it. (3 white, 1 black, 1 red) My new plug only has four plugs. What...
My saw has 5 wires coming out of it. (3 white, 1 black, 1 red) My new plug only has four plugs. What...
(Posted by groove104 8 years ago)
Ridgid K380 Switch Wiring
how do i wire the switch on a k380 my kid pulled all the wires off,there are ten prongs on the switc...
how do i wire the switch on a k380 my kid pulled all the wires off,there are ten prongs on the switc...
(Posted by mrdirect505boy 11 years ago)