Ridgid K-380 Support Question
Ridgid K-380 Support Question
Find answers below for this question about Ridgid K-380.Need a Ridgid K-380 manual? We have 1 online manual for this item!
Question posted by ledwards120 on July 8th, 2015
Why Isn't My K380 Spinning?
my k380 is not feeding out
Current Answers
Answer #1: Posted by TommyKervz on July 9th, 2015 10:53 AM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,813
Member since:
January 10th, 2013 Points: 17,776,813
See troubleshooting on page 14 of the owners manual' Download manual below
Related Ridgid K-380 Manual Pages
Owners Manual - Page 1
Failure to understand and follow the contents of this tool. K-380 Drain Cleaning Machine
OPERATOR'S MANUAL
• Français - 13 • Castellano - pág. 27
WARNING! Read this Operator's Manual carefully before using this manual may result in electrical shock, fire and/or serious personal injury.
Owners Manual - Page 2
... Work Area Set Up ...6 Cleaning Sink Clogs ...7
Operating Instructions Using Manual Feed Machine...7 Using Autofeed Machine ...8
Special Procedures Reverse Operation ...9 Installing Replacement Cable...9 To remove Damaged or Worn Cable ...9 To Install Replacement Cable ...9
Accessories Cable Selection ...10 Additional Tools Available for 3/8″ & 1/2″ Cable ...10
Maintenance Instructions...
Owners Manual - Page 3
K-380 Drain Cleaning Machine
K-380 Drain Cleaner
Record Serial Number below and retain product serial number which is located on nameplate. Serial No.
Owners Manual - Page 4
... adapter plugs. Do not use the cord to a rotating part of flammable liquids, gases, or dust. Replace damaged cords immediately. Carrying tools with grounded surfaces such as to follow all instructions. K-380 Drain Cleaning Machine
General Safety Information
WARNING! Never use any way. Use of other extension cords will not ground the...
Owners Manual - Page 5
Keep proper footing and balance at (800) 519-3456 if you have the tool serviced before using the K-380 Drain Cleaner.
Any tool that may affect the tool's operation. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to bind and are easier to follow the contents of this manual...
Owners Manual - Page 6
... Cart - C-45 IW 1/2″ x 75′ Solid Core (Integral
Wound) Cable - T-260 Tool Set
K-380 Machine w/Gloves & Std. Equipment - Equipment - T-260 Tool Set
Auto Feed Assembly
Two-Wheel Transport Cart
4
Ridge Tool Company Other uses or modifying the drain cleaner for disconnecting tools. Corrosion-resistant cable drum holds 100 feet of 3/8″ diameter cable or 75...
Owners Manual - Page 7
... serious injury, inspect your Drain Cleaning Machine. Placing Mounting Bracket Into Auto Feed
3. Be sure to the OFF position (Figure 4).
2. The following procedures should be aligned with 3/8″ Cable and Tools
Instructions For Mounting Autofeed 1. Screw handle into the center hole of the K-380 using the two (2) 5/16″ x 1″ flat head screws...
Owners Manual - Page 8
... the belt guard and drum should be snapped into the electrical outlet, making sure to be replaced when they become flat. K-380 Drain Cleaning Machine
3. Position the air foot switch pedal for your grip.
9. To remove tool, use the Drain Cleaning Machine until the cord has been replaced.
4. The style of the...
Owners Manual - Page 9
... 50′-100′). Proper Operating Position
Using Manual Feed Machines 1. WARNING Before starting machine, operator's gloved hand... Remember to place a bucket under the sink to start tool and
cable into FOR (forward) position. Operating Instructions
WARNING...become wrapped around the cable, causing serious injury. K-380 Drain Cleaning Machine
the clear path selected earlier. If...
Owners Manual - Page 10
....
NOTE! Turn FOR/OFF/REV Switch to feed the cable into machine. Manually pull sufficient cable out of cable loop.
8
Ridge Tool Company sition. Loosely grasp cable with gloved hand...as required.
Operator should be used to rotate. K-380 Drain Cleaning Machine
4. After establishing flow, increase cutter size to start tool and cable into the line until the cable suddenly ...
Owners Manual - Page 11
... wrapping around your hand or arm. Place FOR/OFF/REV switch to free a tool caught in manual feed mode until the obstruction has been cleared.
8. Tighten screw on back of drum... rotating at a time as you feed the cable into the machine. K-380 Drain Cleaning Machine
7. After establishing flow, increase cutter size to a complete stop . When the tool is used to neutral position. This...
Owners Manual - Page 12
...1/2″ x 50′ w/Solid Core Cable 1/2″ x 75′ w/Solid Core Cable
Additional Tools Available For 3/8″ & 1/2″ Cable
Catalog No.
62990 62995 63000 54837 63005 63010 63020 63025 63030...used on the K-380.
Cables Cables should be identified when outside coils of the drum. When not in a counter-clockwise direction (Figure 9).
K-380 Drain Cleaning Machine...
Owners Manual - Page 13
... injury. WARNING When servicing this section should be used. Failure to the factory. Tool should be taken to a RIDGID Independent Authorized Service Center or returned to follow these...Independent Authorized Service Center, contact the Ridge Tool Company at (800) 519-3456 or http://www.ridgid.com
Ridge Tool Company
11 K-380 Drain Cleaning Machine
Machine Storage
WARNING Motor-driven...
Owners Manual - Page 14
K-380 Drain Cleaning Machine
Chart 1 Trouble Shooting
PROBLEM
POSSIBLE REASONS
SOLUTION
Cable kinking or breaking. Cable used in diaphragm switch...is re-depressed.
Drum stops while pedal is being forced.
Short circuit in pedal or hose.
Wiring Diagram
12
Ridge Tool Company
depressed. pedal is worn, replace it. Let the cutter do the work.
Do Not Force Cable!
Similar Questions
Do You Have Picture Of Your Wheel Kit. Ridged K-380
Wheel kit for K-380, picture please, cost with shipping to 74467 also please would you have a auto f...
Wheel kit for K-380, picture please, cost with shipping to 74467 also please would you have a auto f...
(Posted by mitchintulsa 2 years ago)
Cable 10mm Para Ridgid K380
holaMi pregunta, distintos tipos de sirga para la k380 y precio Gracias
holaMi pregunta, distintos tipos de sirga para la k380 y precio Gracias
(Posted by desatascospacohellin2015 3 years ago)
When Turning On It Is Locked Up Due To The Feed Rollers Not Allowing The Cutting
head to turn
head to turn
(Posted by Janthonysupensky 7 years ago)
How To Connect The Belt What Two Points Of The K-380 Machine Are Belt Pulleys
My belt on the K-380 had came off it's pulley. The belt manual doesn't show how to reconnect the bel...
My belt on the K-380 had came off it's pulley. The belt manual doesn't show how to reconnect the bel...
(Posted by popsrea1 9 years ago)
Ridgid K380 Switch Wiring
how do i wire the switch on a k380 my kid pulled all the wires off,there are ten prongs on the switc...
how do i wire the switch on a k380 my kid pulled all the wires off,there are ten prongs on the switc...
(Posted by mrdirect505boy 11 years ago)