Ridgid K-380 Support Question

Find answers below for this question about Ridgid K-380.
Need a Ridgid K-380 manual? We have 1 online manual for this item!

Ridgid Overview Questions Manuals Reviews Videos Research

Question posted by mitchintulsa on January 11th, 2022

Do You Have Picture Of Your Wheel Kit. Ridged K-380

Wheel kit for K-380, picture please, cost with shipping to 74467 also please would you have a auto feed kit also?

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on January 12th, 2022 6:56 AM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,638,180

1,100
points

https://www.grainger.com/product/RIDGID-Drain-Cleaning-Machine-6NZ26

https://www.amazon.com/Ridgid-26773-K-380-K-400-Assembly/dp/B01MYWQLGT

https://www.amazon.com/Ridgid-49002-T-260-K-380-Machines/dp/B001HWA91K

better to go for amazon

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Ridgid K-380 Manual Pages

Owners Manual - Page 1

Failure to understand and follow the contents of this tool. pág. 27 WARNING! K-380 Drain Cleaning Machine OPERATOR'S MANUAL • Français - 13 • Castellano - Read this Operator's Manual carefully before using this manual may result in electrical shock, fire and/or serious personal injury.

Owners Manual - Page 2

... Work Area Set Up ...6 Cleaning Sink Clogs ...7 Operating Instructions Using Manual Feed Machine...7 Using Autofeed Machine ...8 Special Procedures Reverse Operation ...9 Installing Replacement Cable...9 To remove Damaged or Worn Cable ...9 To Install Replacement Cable ...9 Accessories Cable Selection ...10 Additional Tools Available for 3/8″ & 1/2″ Cable ...10 Maintenance Instructions...

Owners Manual - Page 3

Serial No. K-380 Drain Cleaning Machine K-380 Drain Cleaner Record Serial Number below and retain product serial number which is located on nameplate.

Owners Manual - Page 4

... liquids, gases, or dust. Keep your work area clean and well lit. K-380 Drain Cleaning Machine General Safety Information WARNING! Failure to insure it is left attached to... is OFF before turning the tool ON. Tools create sparks which accept the tool's plug. Electrical Safety • Grounded tools must be caught in personal injury. 2 Ridge Tool Company Never remove the grounding...

Owners Manual - Page 5

... unqualified repair personnel could result in injury. • When servicing a tool, use the K-380 to clean drain lines up to understand and follow maintenance instructions may cause twisting, kinking or breaking of inlet. Specific Safety Information WARNING Read this manual. Call the Ridge Tool Company, Technical Service Department at all times. Such preventive safety...

Owners Manual - Page 6

... operator to the following chart for recommendations. When the cutting tool that is created. T-205 "C" Cutter - A-13 Coupling Pin K-380 Machine w/Gloves & Std. Equipment - Machine w/Gloves & Std. T-260 Tool Set K-380 Machine w/Gloves & Std. Autofeed - T-260 Tool Set Auto Feed Assembly Two-Wheel Transport Cart 4 Ridge Tool Company Refer to relieve tension on choice of 1/2″...

Owners Manual - Page 7

... the autofeed. Figure 4 - Directional Switch In OFF Position Ridge Tool Company 5 Mounting Auto Feed Onto The Frame Machine Inspection WARNING To prevent serious injury, ... the K-380 using the two (2) 5/16″ x 1″ flat head screws. Placing Mounting Bracket Into Auto Feed 3. The following inspection procedures should be aligned with 3/8″ Cable and Tools Instructions For...

Owners Manual - Page 8

... position the power cord along 6 Ridge Tool Company Dull or damaged cutting tools can be snapped into the electrical outlet, making sure to be identified when the outside coils become severely worn or corroded. Do not operate this drain cleaner. 8. K-380 Drain Cleaning Machine 3. Lubricate the Drain Cleaning Machine, if necessary, according to the...

Owners Manual - Page 9

... it at both gloved hands to use the machine. Ridge Tool Company 7 Do not go directly through sink drain. ... compounds have been used out- Proper Operating Position Using Manual Feed Machines 1. When test button is unplugged. Remember to place ...has sufficient wire thickness (16 AWG below . Figure 6 - K-380 Drain Cleaning Machine the clear path selected earlier. If the power...

Owners Manual - Page 10

..., it is apparent that a continuous flush of cable loop. 8 Ridge Tool Company This procedure should release the twist in cable and reduce size of water be used to Reverse Operating Instructions in the cable. Move FOR/OFF/REV switch into the obstruction. Feed lever should immediately respond to free cutter. Neutral Full Advance...

Owners Manual - Page 11

... Remember, when using the feed mechanism the rate of old...reversing feed. The retrieval process is...tool is used to cable bracket. 2. WARNING Never operate this should now feed...feed cable forward. Hand feed the cable into the obstruction. If this machine in an obstruction, refer to a complete stop . K-380...clean cable and tool as they are recommended. When tool is recommended ...

Owners Manual - Page 12

... as required. Cables Cables should be thoroughly flushed with other tools may become flat. 10 Ridge Tool Company Coil Cable Into Drum As Shown 2. No lubrication of...in a counter-clockwise direction (Figure 9). Other accessories suitable for catalog number information. K-380 Drain Cleaning Machine To Install Replacement Cable NOTE! Figure 9 - Accessories WARNING Only the ...

Owners Manual - Page 13

...Center, contact the Ridge Tool Company at (800) 519-3456 or http://www.ridgid.com Ridge Tool Company 11 All repairs made by an authorized RIDGID service technician. Failure to : Ridge Tool Company Technical Service... section should be handled by Ridge service facilities are warranted against defects in rainy weather. K-380 Drain Cleaning Machine Machine Storage WARNING Motor-driven equipment must...

Owners Manual - Page 14

...Hole in one direc- Drum turns in pedal or hose. Take motor to reverse. Wiring Diagram 12 Ridge Tool Company Use 1/2″ cables in or when foot pedal is plugged in 3″ to acid. pedal ...Cable worn out. Let the cutter do the work. K-380 Drain Cleaning Machine Chart 1 Trouble Shooting PROBLEM POSSIBLE REASONS SOLUTION Cable kinking or breaking. Damaged power cord....