Poulan PRRT65 Support Question
Poulan PRRT65 Support Question
Find answers below for this question about Poulan PRRT65.Need a Poulan PRRT65 manual? We have 1 online manual for this item!
Question posted by mcrclarksr on April 6th, 2016
Poulan Pro Tiller
my poulan pro model no. PRRT65 will not shift out of foward into till ,netural, or reverse. I have tried rocking it back and forth while trying to engageing , but no t working
Current Answers
Related Poulan PRRT65 Manual Pages
User Manual - Page 1
Failure to do so can result in U.S.A.
IMPORTANT MANUAL
Do Not Throw Away
OPERATOR'S MANUAL
MODEL:
PRRT65
REAR TINE TILLER
WARNING:
Read this Manual and follow all Warnings and Safety Instructions. ALWAYS WEAR EYE PROTECTION DURING OPERATION Visit our website: www.poulan-pro.com
194800 11.10.04 TR Printed in serious injury.
User Manual - Page 2
... Never attempt to be sure the equipment is in safe working condition.
• Check shear pins, engine mounting bolts...dangerous.
• Never operate the tiller without good visibility or light. • Be careful when tilling in place.
• Keep ...handlebars and do not restrain the machine.
Disengage the tines, shift into neutral before restarting.
• Use extension cords and ...
User Manual - Page 3
...meeting applicable local laws (if any problems you cannot easily remedy, please contact your tiller properly. Other states may have competent, well-trained technicians and the proper tools to...observe the safety rules.
• Follow a regular schedule in effective working order by law (Section 4442 of a new tiller. Should you the best possible dependability and performance. Please read and...
User Manual - Page 4
... parts and hardware you are in the operating position (standing behind tiller handles). OPERATOR'S POSITION
FIG. 1
CONTENTS OF HARDWARE PACK
(2) Handle Locks
(1) Carriage Bolt 3/8-16 UNC x...tightness. TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly easier. ASSEMBLY
Your new tiller has been assembled at the factory with exception of those parts left hand is mentioned in ...
User Manual - Page 5
...CABLES. • While holding handle assembly, cut cable ties securing
handle assembly to remove tiller from handle assembly. Let handle assembly rest on L.H. side of handle lock lever.
&#... LOCK LEVER
CARRIAGE BOLT
FIG. 3
handles_34
HANDLE BASE
PIVOT BOLT LOCKNUT
FIG. 5
5 HANDLE ASSEMBLY
carton_3
SHIFT ROD
FIG. 2
INSTALL HANDLE (See Figs. 3, 4, and 5)
• Insert one handle lock (...
User Manual - Page 6
...
CLUTCH CABLE
CONTROL BAR BRACKET
END OF CLUTCH CABLE
FIG. 6
FIG. 7
REMOVE TILLER FROM CRATE
• Make sure shift lever indicator is important for shipping purposes.
CONTROL BAR BRACKET
CONNECT SHIFT ROD (See Fig. 7)
• Insert end of shift rod into hole of shift lever indicator. • Insert hairpin clip through hole in "N" position (See...
User Manual - Page 7
...shift transmission gears. Levels tilled soil. Used to engage tines. THROTTLE CONTROL -
LEVELING SHIELD - Adjustable to the safety standards of various controls and adjustments. RECOIL STARTER HANDLE - SHIFT LEVER INDICATOR - THROTTLE CONTROL
SHIFT LEVER
DRIVE CONTROL BAR
CHOKE CONTROL SHIFT... tiller to start the engine. CHOKE CONTROL - SHIFT LEVER - Shows which tiller will...
User Manual - Page 8
... indicator in severe eye damage.
NUT "B"
OUTER
NUT "A"
SIDE SHIELD
depth_stake_1
"LOCKED" POSITION
HARD TO SHIFT GEARS
FIG. 11
• Briefly engage drive control bar and release or rock tiller
TURNING
forward and backward until are able to raise tines out of ground.
8 Tines and wheels will not turn .
• Move throttle control...
User Manual - Page 9
..., allow for transporting the tiller. Do not over flowing when engine is accidentally spilled, move machine away from scuffing the ground. • Place shift lever indicator in "F" (forward...COLD WEATHER STARTING.
To avoid engine problems, the fuel system should be raised for deep tilling and lowered for additional information. Do not mix oil with SAE 30 summer weight oil...
User Manual - Page 10
...tiller. Then go back between tilled rows. (See Fig. 14) There are accustomed to handling your tiller,start , move choke control to "RUN" position as engine warms up packed soil before engaging...best results. OPERATION
• Make sure spark plug wire is properly connected.
• Move shift lever indicator to "N" (neutral) position.
• Place throttle control in cold temperatures (...
User Manual - Page 11
...(1oz.)
1 - To receive full value from the warranty, the operator must maintain tiller as instructed in high ambient temperatures. 2 - A new spark plug and clean air filter assure...LUBRICATION CHART"). All adjustments in dirty or dusty conditions.
GENERAL RECOMMENDATIONS
The warranty on this tiller does not cover items that have been subjected to properly maintain your engine run better and ...
User Manual - Page 12
...oil's SAE viscosity grade according to your engine oil level more frequently to prevent oil spill on tiller, and catch oil in a suitable container.
• Remove drain plug. TO CHANGE ENGINE OIL... to avoid possible engine damage from running low on flat least once a year if the tiller is on level surface.
• Oil will drain more often under dusty conditions. • Remove...
User Manual - Page 13
... HOUSING AIR SCREEN
engine_art_61
FIG. 19
MUFFLER
Do not operate tiller without muffler.
SPARK PLUG
Replace spark plugs at the beginning of each tilling season or after every 50 hours of dirt and chaff.
We... engine clean. • Clean air screen frequently using pressurized water (garden hose, etc.) to keep your tiller. • Clean engine, wheels, finish, etc.
User Manual - Page 14
...tilling conditions. HANDLE (HIGH POSITION)
HANDLE LOCK LEVER
HANDLE (LOW POSITION)
TIRE CARE
FIG. 20
CAUTION: When mounting tires, unless beads are not equal, tiller will be different when tiller... height will pull to keep tiller from tipping.
• Remove outer side shield by removing nuts "A" and "B".
• Remove inner side shield by reversing above procedure. If tire pressures...
User Manual - Page 15
...engine pulley first then remove from transmission pulley.
• Place new belt in "ENGAGED" position.
ENGINE PULLEY
CABLE CLIP SCREW
DRIVE CONTROL CABLE
IDLER PULLEY
TRANSMISSION PULLEY
FIG. ... for more tension until about 5/8 inch (16 mm) stretch when drive control bar is engaged.
• Tighten cable clip screw securely. SERVICE AND ADJUSTMENTS
TO REPLACE GROUND DRIVE BELT ...
User Manual - Page 16
... superb tilling performance of this machine the tines should be assembled as shown in Fig. 26. Sharpened tine edges will rotate rearward from above. SERVICE AND ADJUSTMENTS
TINE REPLACEMENT (See Figs. 24, 25, and 26)
CAUTION: Tines are next to work harder ...for sharpness, wear, and bending, particularly the tines which are sharp. A badly worn tine causes your tiller to the transmission.
User Manual - Page 18
...condensation to form and will cause your can if your unit to rust. IMPORTANT: NEVER COVER TILLER WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.
18 sand lightly before storing in the Maintenance...the fuel lines and carburetor are securely fastened. STORAGE
Immediately prepare your tiller for storage at least 10 minutes after adding stablizer to allow the stabilizer to reach the ...
User Manual - Page 19
... Check oil level/change spark plug. 5. Set depth stake for shallower tilling. 2. Check throttle control setting. 3. Engine is not engaged. 2. Oil in fuel.
8. Clogged fuel tank. 9. Dirty/clogged ...fler. 5. Clogged fuel tank. 7.
V-belt not correctly adjusted. 3. Engine runs but tiller won't move
1.
Replace spark plug or adjust gap. 9. Clean and regap or change oil...
User Manual - Page 21
... Service Dept. 1030 Stevens Creek Road Augusta, GA 30907 USA
In Canada contact:
Electrolux Canada Corp. 7075 Ordan Drive Mississauga, Ontario L5T 1K6
giving the model number, serial number and date of purchase of your product and the name and address of the authorized dealer from defects in replacing parts, any...
User Manual - Page 22
Model Number/Manufacturer's I.D. Description of Electrolux Home Products is to continually improve all mechanical ...standards. PARTS AND SERVICE
This product has been expertly engineered and carefully manufactured to our website: www.poulan-pro.com/support.asp
NOTE:
Electrolux Home Products provides parts and service through its products. therefore, all requests for updated information ...
Similar Questions
What Is The Part Number For The Carburetor On Poulan Pro Model 8527es?
I've scoured the owners manual and various parts sites
I've scoured the owners manual and various parts sites
(Posted by gilbertsonryan 4 years ago)
Prrt65 Transmission
Transmission control handle free swings, will not engage an gear. What are the possible causes of th...
Transmission control handle free swings, will not engage an gear. What are the possible causes of th...
(Posted by Anonymous-158947 7 years ago)
Poulan Prrt65 Tiller Transmission Repair
How to diagnose and repair the transmission on a Poulan PRRT65 tiller
How to diagnose and repair the transmission on a Poulan PRRT65 tiller
(Posted by jvanderhart 8 years ago)
How To Replace The Idler Pulley On A Poulan Pro Model Pb195h46yt
(Posted by flynndennisjr 9 years ago)
Manuel For Model # Pr20phst Riding Lawnmower
How do I replace the upper drive belt on the Polan Pro Model # PR20PH42ST riding lawnmower
How do I replace the upper drive belt on the Polan Pro Model # PR20PH42ST riding lawnmower
(Posted by dogboyadams 10 years ago)