Pioneer GM-D8400M Support Question
Pioneer GM-D8400M Support Question
Find answers below for this question about Pioneer GM-D8400M - Amplifier.Need a Pioneer GM-D8400M manual? We have 1 online manual for this item!
Question posted by lukesheridan14 on September 28th, 2013
Amp Problem
How come my light on top is flashing blue then dems down then goes again solid for a second
Current Answers
Related Pioneer GM-D8400M Manual Pages
Owner's Manual - Page 2
... Important 2 Visit our website 2 About This Product 2 CAUTION 2 WARNING 2
Setting the Unit 3
Gain Control 3 LPF (Low-Pass-Filter) Cut Off Frequency
Control 4 Power Indicator (Blue 4 Input Switch 4 Bass Boost Control 4 Setting the Gain properly 5
Connecting the Unit 6
Connection Diagram 7 Solderless Terminal Connections 8 Connecting the Power Terminal 8 Connecting the Speaker Output...
Owner's Manual - Page 3
...amplifier is sold separately. Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to the car body.
• Do not touch the amplifier...supply and subwoofer. Detect the cause and solve the problem, then replace the fuse with liquids due to, ...result from damage. • DO NOT allow amplifier to come into contact with another one of any attached ...
Owner's Manual - Page 4
...
If the sound level is too low, even when the volume of the car stereo used along with this power amplifier is turned up , turn the gain control counterclockwise. • When using with an RCA equipped Pioneer car stereo with an RCA equipped car stereo (standard output of 4 V or more, adjust level to the
NORMAL position. If...
Owner's Manual - Page 5
... a protection function. Power Indicator (Blue)
The power indicator lights when the power is turned off frequency from 40 Hz to 240 Hz.
In this case, it is possible to be emitted from a car stereo external output or a car stereo speaker output. For instruction of connecting the bass boost remote control to the amplifier, see the "Connection Diagram...
Owner's Manual - Page 6
... is cut off the sound output in a few seconds. When you decrease the volume of the head unit and set the gain control of the amplifier to a proper position according to the preout maximum output level of the head unit. Setting the Unit
Setting the Gain properly
• This unit is...
Owner's Manual - Page 7
... with a 12-volt battery and negative grounding. Use of whether the car stereo is at rest or idling.
• DO NOT connect a subwoofer with one of greater value or rating than specified in a short-circuit through the ignition switch (12 V DC), the amplifier will get hot, for a long time while the engine is...
Owner's Manual - Page 8
... Diagram
• This diagram shows connections using external output (subwoofer output).
Car stereo with RCA output jacks
External Output (Subwoofer output)
RCA input jack
Reverse ... Connect to the system remote control terminal of the car stereo (SYSTEM REMOTE CONTROL). Slide the input switch to the positive (+) terminal of the amplifier to the right (RCA). Bass Boost Remote Control
...
Owner's Manual - Page 9
... of the twisted wires.
• Fasten while making all other connections to the amplifier, connect the battery wire terminal of the amplifier to 20 AWG wire for the system remote control wire. Connect the battery wire directly to the car battery positive terminal (+) and the ground wire to the terminal.
• Fix the...
Owner's Manual - Page 10
...Right +
Speaker input wire with the terminal screws. Using the Speaker Input
Connect the car stereo speaker output wires to the amplifier using the supplied speaker input wire with RCA pin cord. • Slide the input...; Use a 10 AWG to 12 mm (3/8 in .).
7 Connections when using the speaker input
Car Stereo Speaker output
10 mm to 16 AWG wire for the speaker wire.
1. Connect the speaker wires ...
Owner's Manual - Page 11
... sure of the following during installation. -Allow adequate space above the amplifier for proper ventilation. -Do not cover the amplifier with a floor mat or carpet.
• DO NOT allow amplifier to come into contact with liquids due to come into contact with the car model and installation location. Use of an improper fuse could result in...
Owner's Manual - Page 12
Place the amplifier where it is to be located.
2.
Tapping screw (4 mm × 30 mm)
Drill a 2.5 mm (1/8 in .) diameter holes at an easily accessible location such as under ... .) diameter hole
Floor mat or chassis
11 Push on the screws with tapping screws (3 mm × 10 mm) at the point marked, and install the amplifier, either on the chassis
1.
Owner's Manual - Page 13
... to possible modification without notice
due to improvements. *Average current drawn • The average current drawn is nearly the maximum current drawn by multiple power amplifiers.
12 Use this value when working out total current drawn by this unit
when an audio signal is input.
Similar Questions
Amp Impedence
was wondering how you would ever run the pioneer gm-xgm-x542 2 channel amp at a 1ohm load and if you...
was wondering how you would ever run the pioneer gm-xgm-x542 2 channel amp at a 1ohm load and if you...
(Posted by truckss415 2 years ago)
Amo Not Working
pioneer 760w maximum power gm-5400t blue light flashes about 5 times then shuts off for about 3 seco...
pioneer 760w maximum power gm-5400t blue light flashes about 5 times then shuts off for about 3 seco...
(Posted by Anonymous-168025 3 years ago)
Help No Sound
ok amp turns on blue light but no sound when radio is on
ok amp turns on blue light but no sound when radio is on
(Posted by wishfuldreamz32 3 years ago)
Pioneer Gm- X924
how many watt is the pionner gm-x924? i want to buy two speacers for him
how many watt is the pionner gm-x924? i want to buy two speacers for him
(Posted by johnnymd98 10 years ago)
Watts
What is the max wattage for this amp is it 500, Or 1000, please let me know
What is the max wattage for this amp is it 500, Or 1000, please let me know
(Posted by Patrickeden316 12 years ago)