Pioneer GM-5500T Support Question
Pioneer GM-5500T Support Question
Find answers below for this question about Pioneer GM-5500T.Need a Pioneer GM-5500T manual? We have 1 online manual for this item!
Question posted by Tankhand0198 on July 13th, 2018
Wont Power On
all wire and fuses good but no power thru amp
Current Answers
Answer #1: Posted by Odin on July 16th, 2018 9:19 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
For possible causes, see About the Protection function at https://www.manualslib.com/manual/784297/Pioneer-Gm-5500t.html?page=2#manual. If the issue persists, Pioneer wants you to "contact your dealer or nearest authorized Pioneer Service Station." For referral to same, use the contact information here--https://www.contacthelp.com/pioneer/customer-service.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Pioneer GM-5500T Manual Pages
Owner's Manual - Page 3
... of the car stereo while the en- If the temperature inside the amplifier gets too
...amplifier will turn off and check the power supply and speaker connections. If this unit to prevent equipment malfunction.
Do not use a fuse of the separately sold with the product may exhaust the battery. The use of an improper fuse could result. The use of a special red battery and ground wire...
Owner's Manual - Page 4
...the connected speaker. !
To ensure continuous sound output with an RCA equipped car stereo (standard output of 500 mV), set amplifier gain control to a level appropriate for a few seconds as a normal ... terminals, turn controls to lower level. If distortion occurs when the car stereo volume is turned up to indicate power ON.
Section
02 Setting the unit
What's what
Front side
Rear ...
Owner's Manual - Page 5
Setting the unit
Relationship between amplifier gain and head unit output power
If amplifier gain is raised improperly, this will simply increase distortion, with high output, if you raise the gain of the amplifier the power changes only slightly.
English
Section
02
En 5 Signal waveform when outputting at high volume using amplifier gain control
Signal waveform distorted...
Owner's Manual - Page 6
... of the car stereo. a Fuse (25 A) × 2 b Fuse (30 A) × 2 c Grommet d Rear side e Front side
1 Special red battery wire RD-223 (sold battery wire, ground wire, speaker wires and the amplifier as far away as possible from the antenna, antenna cable and tuner.
6 En
If the car stereo lacks a system remote control terminal, connect the male terminal to the power terminal via...
Owner's Manual - Page 7
... mode
Other than subwoofer
Speaker channel Two-channel output One-channel output
Power
MAX input: Min. 250 W
MAX input: Min. 800 W
English
Section
03
Speaker impedance is a risk of speaker
Ensure speakers conform to 8 W for a two-channel amplifier, with a 4 W load, either wire two 8 W speakers in parallel, Left + and Right * (Diagram A) or use a single...
Owner's Manual - Page 8
... body.
3 Attach lugs to the terminal. After completing all other amplifier connections, finally connect the battery wire terminal
1 Lug (sold separately) 2 Battery wire 3 Ground wire
4 Connect the wires to wire ends.
Use pliers, etc., to crimp lugs to the positive (+) battery terminal.
1 Car Stereo 2 Speaker output 3 White/black: Left * 4 White: Left + 5 Gray/black: Right * 6 Gray: Right...
Owner's Manual - Page 9
... the units
Section
03
English
1 System remote control terminal 2 Ground terminal 3 Power terminal 4 Terminal screws 5 Battery wire 6 Ground wire 7 System remote control wire
Connecting the speaker output terminals
1 Use wire cutters or a utility knife to strip the end of the speaker wires to wires.
Fix the speaker wires securely with the terminal screws.
1 Terminal screws 2 Speaker...
Owner's Manual - Page 10
... as short-circuit may damage internal parts of installation on the car model. When drilling to install the amplifier, always confirm no parts are to installation in a short-circuit..., they make temporary connections and check to prevent wires from damage.
fier, ensure the following during installation: - Avoid routing wires through the vehicle body.
!
Insert the supplied tapping...
Owner's Manual - Page 11
... out total current drawn by multiple power amplifiers. Additional information
Appendix
English
Specifications
Power source 14.4 V DC (10.8 V to 15.1 V allowable)
Grounding system Negative type Current consumption 29 A (at continuous power,
4 W) Average current drawn ......... 8 A (4 W for two channels)
14 A (4 W for one channel) Fuse 25 A × 2 Dimensions (W × H × D) ... 289...
Similar Questions
Amp Impedence
was wondering how you would ever run the pioneer gm-xgm-x542 2 channel amp at a 1ohm load and if you...
was wondering how you would ever run the pioneer gm-xgm-x542 2 channel amp at a 1ohm load and if you...
(Posted by truckss415 2 years ago)
Pioneer Gm- X924
how many watt is the pionner gm-x924? i want to buy two speacers for him
how many watt is the pionner gm-x924? i want to buy two speacers for him
(Posted by johnnymd98 10 years ago)