Pioneer D812K Support Question
Pioneer D812K Support Question
Find answers below for this question about Pioneer D812K - AV Receiver - 5.1 Channel.Need a Pioneer D812K manual? We have 1 online manual for this item!
Question posted by HIDALGOEVA80 on May 19th, 2012
Pioneer D812k Reciever-amplifier
HOW TO RESET D812K AMPLIFIER TO ITS ORIGINAL STATUS?
Current Answers
Answer #1: Posted by addisk on May 19th, 2012 5:07 AM
addisk
Member since:
May 8th, 2012 Points: 694,616
Member since:
May 8th, 2012 Points: 694,616
Resetting the main unit
Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel
controls to do this.
1 Switch the receiver on.
2 While holding down the TONE button, press and hold the STANDBY/ON button
for about three seconds.
3 When you see RESET? appear in the display, press the TONE button.
OK? shows in the display.
4 Press TONE once more to confirm.
OK appears in the display to indicate that the receiver has been reset to the factory default
settings
Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel
controls to do this.
1 Switch the receiver on.
2 While holding down the TONE button, press and hold the STANDBY/ON button
for about three seconds.
3 When you see RESET? appear in the display, press the TONE button.
OK? shows in the display.
4 Press TONE once more to confirm.
OK appears in the display to indicate that the receiver has been reset to the factory default
settings
Related Pioneer D812K Manual Pages
Owner's Manual - Page 2
Please write this Pioneer product. Please read through these operating instructions so you will expose you to lead, a chemical known to the State of California and other governmental entities ...
Owner's Manual - Page 4
... additional amplifiers 26 AC outlet 27 Power cord caution 27 Operating other Pioneer components . . . . 28
04 Controls and displays
Front panel 29 Display 31 Remote control 33
05 Playing sources
Introduction to Sound Modes 36 Stereo/Direct 36 Standard mode 36 Advanced Surround modes 37
Choosing the input signal 37 Listening to multi-channel...
Owner's Manual - Page 7
... the plus and minus sides of used batteries, please comply with governmental regulations or environmental public instruction's rules that is emitting infrared rays. • The receiver is located near a device that apply in such hazards as leakage and bursting.
Observe the following precautions:
• Never use different batteries together. • When...
Owner's Manual - Page 12
...8226; Depending on page 38 if you need to this ) if you want multi-channel surround sound.
12
En Surround back speaker (or subwoofer)
VSX-D812
R SURROUND BACK L
4 Plug in the receiver and switch it isn't, press DVD/LD on the remote control to set -see ... more on , followed by your DVD player, your DVD player or source discs, you may only get digital 2 channel stereo and analog sound.
Owner's Manual - Page 17
... to ensure you want to record with, you need to hook up four plugs to the receiver (a set of stereo inputs and a set of the signal. See page 16 for the VSX-D712 are unsure ...R AUDIO L
VIDEO
IN CONTROL
OUT
MONITOR OUT SUB W.
Connecting audio components
To begin set up, connect your system. Connecting up
03
• If you have an LD player, you need to make sure the power is ...
Owner's Manual - Page 26
...Surround channel amplifier
Surround back channel amplifier
ANALOG IN INPUT
Center channel amplifier
Powered subwoofer
• To hear sound only from the pre-outs, disconnect any connections.
• The arrows indicate the direction of the VSXD712. Make the connections shown below to add amplifiers to power your speakers. 03
Connecting up
Connecting additional amplifiers
This receiver has...
Owner's Manual - Page 27
... a monitor, TV set to avoid overheating and fire risk. Do not pull out the plug by the receiver's power switch. This can cause a fire or give you find it with high power consumption to malfunction....plug from the wall socket when not in the cord or tie it damaged, ask your nearest Pioneer authorized service center or your hands are not likely to large.
• VSX-D712 only -...
Owner's Manual - Page 28
...), you can point the remote controls of other compatible Pioneer products
28
En OUT
IN
CONTROL
Receiver
CONTROL IN OUT
Remote control unit
Other Pioneer products with CONTROL terminals
Connect to the other Pioneer components at the receiver's remote sensor.
The remote control signals are received by the remote sensor of this unit, and sent to...
Owner's Manual - Page 36
... sound and is selected, the receiver automatically switches to the source audio signal as possible.
• If you switch on page 40. 05
Playing sources
Chapter 5:
Playing sources
Introduction to a 2 channel source:
Pro Logic II Movie (MOVIE) This mode gives 5.1 channel surround sound. In STEREO, you'll hear the audio with your subwoofer depending...
Owner's Manual - Page 37
... Surround Back mode (VSB) on page 41 and Using the Surround Back Channel (SB CH) on page 40. Use with alot of the receiver to be used with mono soundtracks. TV Surround (TV. Most Advanced Surround modes are also suited for a stereo surround effect.
Playing sources
05
Neo:6 Music (MUSIC) This mode gives...
Owner's Manual - Page 39
... you select one of the Advanced Surround options, Dolby Pro Logic, Dolby Digital and DTS decoding is selected, the receiver automatically switches to 90 by pressing EFFECT +/- . Using Stereo/Direct
When you select STEREO or DIRECT, you will automatically be selected.
• You can't use the STANDARD mode with 96kHz PCM or DTS...
Owner's Manual - Page 40
... it was originally encoded, in which case you can choose to listen to other kinds of source
SB CH MODE
DTS-ES/Dolby Digital Matrix encoded multi-channel sources with 6.1 surround
Dolby Digital/DTS encoded multi-channel sources
ON AUTO
ON AUTO
Dolby Digital/DTS encoded stereo sources, Stereo sources
ON AUTO
Analog 2-channel (stereo) source
ON...
Owner's Manual - Page 41
... AUTO
Dolby Digital/DTS encoded stereo sources, Stereo sources
ON AUTO
Analog 2-channel (stereo) source
ON AUTO
41
En Playing sources
05
Using the Virtual Surround Back mode (VSB)
Selecting this effect to 6.1 encoded sources like Dolby Digital EX or DTSES (VSB AUTO), or you can simply switch it was originally encoded. For example, you...
Owner's Manual - Page 44
... when using the Pioneer S-FCRW230/ 730 speaker system, make these settings...the attenuator level for details on the following pages for the LFE channel. It will be easiest to the following pages). Subwoofer setting (page... back subwoofer setup.
06
Setting up the receiver
Chapter 6:
Setting up the receiver
Choosing your current speaker system or add new speakers, etc.). You only...
Owner's Manual - Page 50
... optical DIGITAL IN jacks on the back of input 2 automatically switches input 2 to OFF. Digital input settings
Here you tell the receiver what components you have hooked up the receiver
Surround back channel input setting
(VSX-D812 only)
• Default setting: SB 2ch IN
You only have to make this is the case...
Owner's Manual - Page 63
Controlling the rest of your system
09
Preset Code List
You should have no problem controlling a component if you find the manufacturer in ...MITSUBISHI 609, 610, 602,
621 GOLDSTAR 610, 623, 621,
602 JVC 613, 623 RADIOSHACK610, 623,
621, 602 FUNAI 658 GRANDIENTE 630 LOEWE 607 PIONEER 600
STB (SATELLITE/
CATV) TV/SAT TV CONT Manufacturer Code
JERROLD 711, 701, 702, 712, 704, 713 , 703, 714, 716, 715...
Owner's Manual - Page 64
09
Controlling the rest of your system
SONY 301, 316, 317, 318 TEAC 305, 306, 327, 324,
325 TECHNICS 304, 326
YAMAHA 315 , 314 , 328, 347
PIONEER 300, 345
MD
Manufacturer Code
SONY 901 KENWOOD 903 SHARP 902
TEAC 904 ONKYO 905 DENON 906 PIONEER 900, 902, 907
64
En
Owner's Manual - Page 65
.... This could cause the receiver to shut off automatically. • If the STANDBY indicator blinks and the power shuts off automatically, take the unit to your nearest Pioneer authorized service center or your... power does not turn muting off the equipment causing the noise or move it away from the receiver. • Place the antenna farther away from the outlet, and insert again. • Make...
Owner's Manual - Page 68
... Ratio Mono: 73 dB
(at 85 dBf) Stereo: 70 dB (at 8 ohms, from 20 Hz to 108 MHz Usable Sensitivity Mono:13.2 dBf, IHF
(1.3 µV/ 75 Ω) 50 dB Quieting Sensitivity. . . . . . 10 Additional information
Specifications
Amplifier section
Continuous average power output of 100 watts* per channel
(VSX-D812 only)
(1kHz, 1.0 %, 8 Ω)
Signal-to...
Owner's Manual - Page 69
...
• Never use thinners, benzine, insecticide sprays or other chemicals on Power Output Claims for Amplifiers. ** Measured by Audio Spectrum Analyzer.
69
En
Furnished parts AM loop antenna 1 FM wire ...Regulation rule on or near this unit, since these will corrode the surface. Additional information
10
Stereo Separation 40 dB (1 kHz) Frequency Response 30 Hz to 15 kHz
(±1 dB) ...
Similar Questions
I Bought The New Player And We Cannot Get Any Sound. It Is Hooked Up To A Receiv
(Posted by Maryannhamelin 2 years ago)
Reset Pioneer Av Receiver Vsx-522k
(Posted by kwstallard80 2 years ago)
Reset My Av Receiver
sir i have pioneer vsx521 k ,i am facing a lot of problem in this system,now i had wrongly press rem...
sir i have pioneer vsx521 k ,i am facing a lot of problem in this system,now i had wrongly press rem...
(Posted by rameshvkj 10 years ago)
Video From Satellite Receiver Wont Work
Ive had my pioneer hooked up to my satellite for over 2 years and now my video wont come on I still ...
Ive had my pioneer hooked up to my satellite for over 2 years and now my video wont come on I still ...
(Posted by mart13 11 years ago)
