Home » Pfaff » Sewing Machines » Pfaff hobbylock 776

Pfaff hobbylock 776 Support Question

Find answers below for this question about Pfaff hobbylock 776.
Need a Pfaff hobbylock 776 manual? We have 1 online manual for this item!

Pfaff Overview Questions Manuals Reviews Videos Research

Question posted by Butterfly470179 on March 28th, 2022

Tension Settings For Normal Serge

The person who posted this question about this Pfaff product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on March 29th, 2022 8:09 AM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,641,150

1,100
points

https://www.youtube.com/watch?v=JQsiWsdnJBc

https://www.manualowl.com/p/Pfaff/hobbylock-776/Manual/184561

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Pfaff hobbylock 776 Manual Pages

Owner's Manual - Page 2

...Adjusting the stitch length 16 c. Replacing the light bulb 20 F. CONTENTS 2 A. Operating the machine g a. Thread tension adjustment (Normal hemming) c. Parts names 4 B. Test sewing b. Dial chart for thread tension adjustment Relation chart for the sewing 4 a. Lubrication Opening and closing looper cover and side cover 6 6 g. Differential feed mechanism 17...

Owner's Manual - Page 5

... off the machine, sewing light is turned off the lamp Sewing light is switched on and by the master switch located right side of your foot from the pedal. c. S. Preparation This machine must be used on the pedal. To stop the machine, lift your foot lightly on a flat and horizontal surface or purpose-built sewing machine table...

Owner's Manual - Page 6

e. Lubrication The bushings and other important parts are made from special materials and only require lubrication once or twice a month. When oiling always be sure to the areas indicated. 5 Apply just one or two drops of oil to use a good quality sewing machine oil.

Owner's Manual - Page 7

... close the looper cover, push the looper cover upwards lightly towards you to the direc tion of the arrow. Ensure that it down towards the machine until it to obtain a correctly formed seam. 3. f. To open the side cover, push it will assist you . 3.

Owner's Manual - Page 10

...machine a. Test sewing After threading, be adjusted accordingly. Hold the 4 threads by your left hand and turn the pulley 2 or 3 turns slowly towards you in achieving the best results. Dial chart for thread tension... Thread tension adjustment (Normal hemming) The correct thread tension varies depending on the fabric and type and thickness of the upper cutter and start sewing slowly. ...

Owner's Manual - Page 11

Correct thread tension Top side 10 Left needle thread Right needle thread Relation chart for fabrics and thread stitch length Normal hemming Roll hemming Fabrics Light Organdy, light-knit fabric, Taffeta, silk,lining materials Medium Cotton, tricot, linen, dress materials Heavy Tweed, suit materials, denim, heavy ...

Owner's Manual - Page 12

The sketch shows the left needle thread tension is too loose. 4. Incorrect thread tension and how to adjust 1. The sketch shows the right needle thread tension is too loose. 11 The sketch shows the left looper thread tension is too loose. 3. f. The sketch shows the right looper thread tension is too loose. 2.

Owner's Manual - Page 13

... foot by the roll hemming foot. The foot for normal sewing can be achieved. 1 .Raice the presser foot and then push up the small lever. Roll hemming foot . By following this instruction, very good sewing results can then be engaged. • Correct thread tension of roll hemming o 0 0 0 00 Narrow hemming 12 Top side Fold...

Owner's Manual - Page 14

... approximately 5 the seam then cut the thread chain. • Securing the seam: Tie the thread chain. h. For crochet needle can be used to observe during sewing • • PtTfhalheabecrfneiocotsthlwoebiwlelfflayobfreresiecedcwoumnatudhmteeoermnftichrasietnticgcfaeultwoltytesrseatwiant.cndhdegsl,oenwttheiyer • guide by hand. Points to knit pull fabric, a the thread •...

Owner's Manual - Page 15

... to 7 mm. (Standard seam width is 5,5 mm). • For narrow seam sewing. 1. I. 3 thread overedge seam Three-thread sewing is possible by using either right or left hand needle. 2. Use the right hand...thread and right & left looper thread. 3. Threading procedure is as usual. • For wide seam sewing. 1 Remove the right hand needle. 2. HUH Narrow seam Use right hand needle only. [il1 1 ...

Owner's Manual - Page 17

... the arrow - Adjusting the stitch length 1. Fabric Nylon, tricot, lining fabrics, satin, polin, silk, and light cotton Jeans (Normal fabrics) Jersey, medium cotton, nicki fabrics, light knitting NOTE:To achieve the correct final setting it up or down. 3. Fully open the side cover by sliding it will eliminate uneveness and puck ering...

Owner's Manual - Page 18

... SOURCE. 1. Light weight materials needing a finer needle, with a thicker needle for heavier weights. Fitting the left needle screw Ensure you are : 130 / 705H, and the normal recommended size is No. 90. slant and do so could result in the direction of the arrow), raising the needle (s) to the highest position. Then...

Owner's Manual - Page 19

...Turn the release knob away from you , lower it is now ready for normal operation. 3. It is necessary to its bottom positiOn at which point the ... remove the upper knife. When in the cutting position and, by turning the pulley wheel by hand towards you ). To set the cutting position: Place the upper knife in this position, re-tighten the screw (A) securely, using a screwdriver, retighten ...

Owner's Manual - Page 20

... bulb only. 19 Replacing the light bulb FIRST DISCONNECT ThE MAINS PLUG FROM THE POWER SOURCE • Loosen the screw of the rear of the machine body and remove the lamp cover. • Turn the bulb in Insert the new direction bulb by (1) and remove it in the direction (2). Replacing the...

Owner's Manual - Page 21

Sewing problems and solutions Used correctly, your machine should overcome most of thread tensions Set thread tensions correctly. Insert new needle correctly. Insert needle correctly. Use needle system 130 / 705H only. Thread correctly. Thread breakage Skipped stitches Incorrect stitch • formation Puckered ...