Home » Pfaff » Sewing Machines » Pfaff hobbylock 776

Pfaff hobbylock 776 Support Question

Find answers below for this question about Pfaff hobbylock 776.
Need a Pfaff hobbylock 776 manual? We have 1 online manual for this item!

Pfaff Overview Questions Manuals Reviews Videos Research

Question posted by lilih on April 24th, 2022

I Need A Replacement Feet For My 776.the Pin Has Broke And Is Not Holding The Fe

The person who posted this question about this Pfaff product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

Requests for more information

Request from lilih on April 24th, 2022 5:14 AM
The horizontal pin has come away and is not holding the feet in place when I raise the lever.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by SonuKumar on April 24th, 2022 7:41 AM

This answer was accepted by the poster of the original question.

SonuKumar

Member since:
May 9th, 2021

Points: 16,648,150

1,100
points

https://www.ebay.com/itm/275144059667

https://picclick.com/Pfaff-Hobbylock-776-Serger-Sewing-Machine-Foot-Pedal-144333642171.html

https://www.sewingpartsonline.com/pfaff-776-sewing-machine-parts.aspx

https://www.recipesfo.com/hobbylock-776-parts/

Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.

Regards,
Sonu
Your search handyman for all e-support needs!!

Related Pfaff hobbylock 776 Manual Pages

Owner's Manual - Page 2

... thread stitch length 9 9 10 10 e. Dial chart for thread tension adjustment Relation chart for the sewing 4 a. Incorrect thread tension and how to observe during sewing 13 14 i. 3-thread overedge seam 15 D. Roll hemming h. Replacing needle (S) 18 e, Replacing the upper knife 19 f. Differential feed mechanism 17 d. Lubrication Opening and closing looper cover and side...

Owner's Manual - Page 3

A. Parts name o Front side Telescopic thread reel stand bar • Rear side Pulley wheel feet 2

Owner's Manual - Page 5

... is switched on and off by switching off . 4 By switching on the machine, sewing light is turned off the machine, sewing light is turned on a flat and horizontal surface or purpose-built sewing machine table. Preparation This machine must be used on and by the master switch located right side of your foot from the pedal. d. b. Fitting...

Owner's Manual - Page 6

e. Apply just one or two drops of oil to use a good quality sewing machine oil. Lubrication The bushings and other important parts are made from special materials and only require lubrication once or twice a month. When oiling always be sure to the areas indicated. 5

Owner's Manual - Page 7

To open the looper cover, slide the looper cover to the right until it clicks and it down towards the machine until it immediately aligns above the thread reel bar pins. 4. Ensure that it locks. 2. Tweezers from the accessories bag will close securely. ff7 6 To close the looper cover, push the looper cover...

Owner's Manual - Page 10

... 9 Thread tension adjustment (Normal hemming) The correct thread tension varies depending on the fabric and type and thickness of the upper cutter and start sewing slowly. OPerating the machine a. b. C. Hold the 4 threads by your right hand. Insert the cloth under the presser foot up to the edge of the thread and must therefore...

Owner's Manual - Page 13

... left needle first. For the roll hemm ng (narrow / foldover hemming) replace the normal stitch foot by the roll hemming foot. With the presser foot... the small lever. Roll hemming foot . By following this instruction, very good sewing results can then be taken off. 2. Roll hemming . The foot for normal sewing can be engaged. • Correct thread tension of roll hemming o 0 0...

Owner's Manual - Page 14

...; Tftiahgbihsrtiecmns.atchheWinuhepepwneilrlseskewnwifienfgrsocmvreewrfyi.ne(hseetoeavviylelruyfsatrhbaetriaiocvnsy),. • W Clhoaaohuvseteienonbne:steehnwe isnuegwppinfeigrneoknnfiafhbeeraiscvcsyr,efwabreraimcgsae.imn biferyotou 13 Do not push or pull avoid the possibility of sew approximately 5 the seam then cut the thread chain. • Securing the seam: Tie the thread chain. h.

Owner's Manual - Page 15

...[il1 1 14 Seam width can be changed from 5 mm to 5 mm.(Standard seam width is 5,5 mm). • For narrow seam sewing. 1. Seam width can be changed from 3 mm to 7 mm. (Standard seam width is 3.5 mm). Use the left hand needle thread ... is possible by using either right or left hand needles. I. 3 thread overedge seam Three-thread sewing is as usual. • For wide seam...

Owner's Manual - Page 18

...(eoosno)n,veeeindisnleetrhtheonldneewere(dsnl)ee(mesd)alkefia(ncsge) towards you . Light weight materials needing a finer needle, with a thicker needle for heavier weights. The recommended needle... the screw. Then using Needle sizes from No.75 to No.90 may be used. d. Replacing needle (S) DURING THIS OPERATION DISCONNECT THE MAINS PLUG FROM THE POWER SOURCE. 1. Removing needle (s)...

Owner's Manual - Page 19

... position, then, by the carrier stopper (approximately horizontal to you , lower it is now ready for normal operation. 3. When in the opposite manner as required. e. Replacing the upper knife DURING THIS OPERATION DISCONNECT THE PLUG FROM THE MAINS OUTLET. 1. It is necessary to touch the blade. 2.

Owner's Manual - Page 20

...; Loosen the screw of the rear of the machine body and remove the lamp cover. • Turn the bulb in the direction (2). Caution: Use a maximum 1 5 watt bulb only. 19 pushing upward, turning it in Insert the new direction bulb by (1) and remove it. Replacing the lower knife DURING ThIS OPERATION DISCONNECT THE...

Owner's Manual - Page 21

... which should operate efficiently and without difficulty. Do not pull or push material during sewing. Check whether thread is bent or point damaged Needle not correctly inserted Material pulled ... which usually results from time to incorrect threading Reduce thread tension Thread correctly Sewing foot is not fed correctly Incorrectly threaded Thread has caught Thread tension too ...