Home » Pfaff » Sewing Machines » Pfaff hobbylock 776

Pfaff hobbylock 776 Support Question

Find answers below for this question about Pfaff hobbylock 776.
Need a Pfaff hobbylock 776 manual? We have 1 online manual for this item!

Pfaff Overview Questions Manuals Reviews Videos Research

Question posted by istyles on May 20th, 2014

Where Can I Get The Screws For The Foot Motor For The Hobylock Overlocker 776

The person who posted this question about this Pfaff product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Pfaff hobbylock 776 Manual Pages

Owner's Manual - Page 2

...g. d. Incorrect thread tension and how to adjust the foot controfler 4 4 d. Adjusting the seam width 16 b. Replacing needle (S) 18 e, Replacing the upper knife 19 f. Replacing the lower knife 19 g. Points to observe during sewing 13 14 i. 3-thread overedge seam 15 D. CONTENTS 2 A. Operating the machine g a. Preparation for fabrics and thread stitch length 9 9 10...

Owner's Manual - Page 4

... Thread stripping discs (4 pcs.) Li Needle • Controller Dust cover 3 • Accessories Accessories case Screw driver Screw driver (For needle) Iweezers Oiler • Looper mechanism • Specifications Maximum speed Overlock seam width Stitch length Presser foot Presser foot lift Needle Number of threads Lubrication Dimentions Net weight 1 300 s.p.m. 3.5mm (standard) 1.0 - 4.0mm...

Owner's Manual - Page 5

... you press down gently, the machine will begin to adjust the foot controller Place the tip of the body. Turning on the pedal. c. By switching on the machine, sewing light is turned on and by switching off the machine, sewing light is switched on a flat and horizontal surface or purpose-built sewing machine table. When you press more...

Owner's Manual - Page 6

When oiling always be sure to the areas indicated. 5 e. Lubrication The bushings and other important parts are made from special materials and only require lubrication once or twice a month. Apply just one or two drops of oil to use a good quality sewing machine oil.

Owner's Manual - Page 7

.... g. Threading must be done carefully in accord ance with the threading procedure in order to the right until it clicks and it down towards the machine until it locks. 2. To open the side cover, push it immediately aligns above the thread reel bar pins. 4. Ensure that it to the right, swing...

Owner's Manual - Page 10

C. Test sewing After threading, be adjusted accordingly. OPerating the machine a. Hold the 4 threads by your right hand. Insert the cloth under the presser foot up to the edge of the thread and must therefore be sure to the chart below it will assist you with your left hand and ...

Owner's Manual - Page 13

... can then be taken off. 2. Normal hemming toot • How to replace the presser toot Remove the left needle first. The foot for normal sewing can be engaged. • Correct thread tension of roll hemming o 0 0 0 00 Narrow hemming 12 Top side Fold-over hemming g. For the roll hemm ng (narrow / ...

Owner's Manual - Page 14

For crochet needle can be used to observe during sewing • • PtTfhalheabecrfneiocotsthlwoebiwlelfflayobfreresiecedcwoumnatudhmteeoermnftichrasietnticgcfaeultwoltytesrseatwiant.cndhdegsl,oenwttheiyer • guide by hand....,efwabreraimcgsae.imn biferyotou 13 Do not push or pull avoid the possibility of sew approximately 5 the seam then cut the thread chain. • Securing the...

Owner's Manual - Page 15

...hand needles. Seam width can be changed from 5 mm to 5 mm.(Standard seam width is 5,5 mm). • For narrow seam sewing. 1. Wide seam Use left looper thread. 3. Seam width can be changed from 3 mm to 7 mm. (Standard seam width is ... right & left hand needle. 2. Remove the left looper thread. 3. I. 3 thread overedge seam Three-thread sewing is as usual. • For wide seam...

Owner's Manual - Page 18

....ewtisstncbwoirsuethtwietmonrafpotrtorehryrfetietarttaonincftoghptluolnontewepebedradotlchelpekse. Fitting the left needle screw Ensure you by hand, (in....75 to not do not force the screw. The recommended needle system are using a screwdriver, re-tighten the needle clamp screw securely. slant and do so could result...

Owner's Manual - Page 19

... a vertical position, then, by releasing pressure on the presser foot. To remove the upper knife. Then loosen the retaining screw and take off the knife, taking care not to adjust, loosen the upper knife screw (A) and raise or lower as abnve), and, using a screw driver. To set the cutting position: Place the upper knife...

Owner's Manual - Page 20

Replacing the light bulb FIRST DISCONNECT ThE MAINS PLUG FROM THE POWER SOURCE • Loosen the screw of the rear of the machine body and remove the lamp cover. • Turn the bulb in Insert the new direction bulb by (1) and remove it in the direction (2). Replacing the ...

Owner's Manual - Page 21

... which usually results from time to incorrect threading Reduce thread tension Thread correctly Sewing foot is caught at the reel stand, etc. Thread breakage Skipped stitches Incorrect... the presser foot lever down. Do not pull or push material during sewing. Incorrect setting of these difficulties. Sewing problems and solutions Used correctly, your machine should overcome ...