Pfaff ambition Support Question
Pfaff ambition Support Question
Find answers below for this question about Pfaff ambition.Need a Pfaff ambition manual? We have 1 online manual for this item!
Question posted by mlavca on January 2nd, 2014
Button Holer
I set up my ambition 1.0 as directed, put button in holer, put the foot on, set machine, pull lever down and when it goes it only does a very tiny hole. I cannot seem to get it to read the size of the button. What am I doing wrong. Do I need to select something each time I do a new button to tell the machine?
Current Answers
Related Pfaff ambition Manual Pages
Owner's Manual - Page 2
...sewing machine. To reduce the risk of burns, fire, electric shock, or
injury to person:
• This sewing machine is not intended for use by pulling... ventilation openings of the sewing machine and foot controller free from the accumulation of the sewing machine by a person responsible ...sewing machine should be followed, including the following:
Read all instructions before cleaning.
Owner's Manual - Page 3
... feed dogs 2:9
Presser foot lift 2:9
Changing the presser foot 2:9
Buttons for ambition™ 1.5 machine 2:10
Touch screen for ambition™ 1.5 machine 2:11
Buttons for ambition™ 1.0 machine 2:12
Graphic Display on purchasing your sequences 4:5 Save sequence 4:5 Load sequence 4:6
Sewing a sequence 4:6
Maintenance
5:1
Cleaning the machine 5:1
Replacing the stitch...
Owner's Manual - Page 6
...machine will sew a buttonhole to set the size of the hem edge. Seam ripper & brush (as one) 47. The groove on either the right or the left to sew closer to zipper teeth. Stylus (ambition™ 1.5) 48. Zipper foot 4 with IDT™ system This foot... Important: Make sure that button size.
Fancy stitch foot 2A When sewing decorative stitches or short zigzag stitches and other utility stitches...
Owner's Manual - Page 7
...or topstitching.
Zigzag stitch 65
Reinforce seams, clean finish, stretch sewing. Triple stretch stitch
Sewing elastic, darning, patching and decorative sewing. Basting stitch 4-
Closed overlock
Seam and overcast in one stitch. Touch foot control to sew another stitch. Blindhem stitch 16 14
Sewing blindhems on stretch fabrics. Elastic overcast
Seam and overcast stretch...
Owner's Manual - Page 11
... cord into the wall socket.
3.
Slide the tray on the bottom right side of electric shock, this sewing machine, foot control model C-9002
manufactured by CHIENHUNG TAIWAN., LTD
B
must be used.
1. To reduce the risk of the machine (B). Preparations
Unpacking
1.
A
2. Connect the power cord to install the proper outlet. Place all outer packing material...
Owner's Manual - Page 14
...use the needle threader for twin needle
Replace the sewing needle with a twin needle. There are also... sized spool cap. Pull both threads between the tension discs (B).
3. Make sure that require manual threading of the needle. Press the needle up lever ...lowering the presser foot.
1.
Place one thread into the slot on the left -hand threading slot.
4.
Threading for size 60 needles or...
Owner's Manual - Page 16
..., PFAFF® ambition™ sewing machine provides the ideal
F
solution: the integrated dual feed, IDT™ system. To cut -out (F). The even feeding action
also ensures perfect matching of the seam. Preparations
Inserting the bobbin
Make sure that the needle is fully raised and the machine is turned off blade at point (E).
6.
Pull the IDT...
Owner's Manual - Page 18
...: Change the needle often. Preparations
Needles
The sewing machine needle plays an important role in the fabric.
Embroidery needle (D) Embroidery needles have a slightly rounded point and come in a variety of fabric types and weights. Denim needle (E) Denim needles have a special scarf to poke holes in a variety of sizes. For canvas, denim, microfibers...
Owner's Manual - Page 19
... foot Press the presser foot downwards until it disengages from you are sewing on heavy fabric or several layers of the free arm to the left. Loosen the needle screw. Insert the new needle, using the multi-purpose tool.
Tighten the needle screw as tight as it will not raise immediately when the lever...
Owner's Manual - Page 20
... machine will be lit and the machine sews in reverse for ambition™ 1.5 machine
12
11
11
Needle up or down is lit when needle down . The indicator is activated.
Speed control lever (4) The speed control lever sets the maximum sewing speed. The indicator stays lit until you press the button again to the left. You can also tap the foot...
Owner's Manual - Page 22
.... For straight stitches, use . Speed control lever (4)
The speed control lever sets the maximum sewing speed. The reverse indicator (6) will then stop position is lit to sew. Stitch length or stitch density (10) Increase or decrease the stitch length using the "+" and "-" buttons. The setting of the stitch again without using the foot control. Start/stop (5)
Press this...
Owner's Manual - Page 24
... corner.
ambition™ 1.5
Settings menu (1.5)
Touch the settings menu tab...sewing machine. Touch the calibration icon to activate both settings.
All settings are stored even when the machine is turned off .
2:14 When a twin needle size...foot or stitch plate. A warning pop-up informs you can adjust the machine settings and screen settings. The selected width is shown in sewing...
Owner's Manual - Page 25
Settings menu (1.0)
Open by pressing the up and down arrow buttons on the wheel to the needle, presser foot or stitch plate.
Stitch width safety Press OK (B) to activate.
ambition™ 1.0
Twin needle
Press OK (B) to avtivate. A checkmark appears in sewing mode.
When a twin needle size is selected, the width of the twin needle box will be...
Owner's Manual - Page 33
One step Buttonhole Foot 5B
1. Attach buttonhole foot 5B and pull out the button holder plate. Make sure that the marking on the fabric is pulled though the hole in this book to find descriptions of the buttonhole foot.
6. Sewing
Buttonholes
Your machine's buttonholes are specially adjusted for different kinds of the buttonhole on your garment under the foot.
4. Mark...
Owner's Manual - Page 35
Darning and mending
Darning a small hole or a tear before it .
4. Your sewing machine will be sewn using the buttonhole foot 5B. Set the length of the seam best.
Use the side that suits the thickness of the darning stitch by pulling out the button holder plate and lower the buttonhole lever to sew the stitch.
To set a different length of the...
Owner's Manual - Page 36
...IDT™ presser foot #820 925- 096.
Tip! Take one another to choose from the center of the quilt. Take a few stitches right next to one stitch and pull the bobbin thread ... blocks. Crazy quilt stitching
Embellish your sewing machine for stippling by pin basting your quilt through all layers with safety pins, starting from . Set your quilt with decorative stitches.
Now ...
Owner's Manual - Page 39
... can now be moved through the sequence using the left and right arrows on the touch wheel. Cursor 4. Move cursor
ambition™ 1.5
3
1
2 5 4 6 7
8
9
10 11
12
Sequencing
Create a sequence
• Press ... function on your machine makes it will be used for sequencing except for buttonholes, darning stitches, button sewing and bartacks. All stitches in the same sequence.
Owner's Manual - Page 45
... turn off the machine. Push the bobbin cover release button (A) to the right and remove the bobbin cover (B) and the bobbin. Cleaning under the bobbin area Clean the area under the bobbin case after sewing several projects or any dust or lint built up.
Maintenance
Cleaning the machine
To keep your sewing machine operating well, clean...
Owner's Manual - Page 46
... the wall socket. Calibrate is threaded. Is the correct presser foot used ? Check how the machine is found in the settings menu. Did you insert a wrong needle? Is the stitch plate hole damaged?
Wrong stitch, irregular or narrow stitch?
Push bobbin winder lever to the proper size for the thread and fabric. Did you insert a wrong...
Owner's Manual - Page 47
... slubbed thread?
Is the stitch plate hole damaged? Change the stitch plate. Check needle thread tension and the threading. Bobbin thread breaks Did you have followed this trouble shooting information and still have problems, take your sewing machine to your dealer. Check bobbin winding. Have your sewing machine serviced regularly by use of your thread...
Similar Questions
I'm Trying To Make A Button Hole, The Sewing Machine Is Not Advancing The Fabric
(Posted by paulinegp22 4 years ago)
Pfaff 259 Sewing Machine Won't Run With Foot Petal
I have a pfaff 259. When I push on the foot petal the motor runs but the machine itself doesn't run....
I have a pfaff 259. When I push on the foot petal the motor runs but the machine itself doesn't run....
(Posted by Aemazing 8 years ago)
Bobbin Holder Not Moving
my bobbin thread was misbehaving and making a big mess while in reverse, while my top thread was fin...
my bobbin thread was misbehaving and making a big mess while in reverse, while my top thread was fin...
(Posted by artphair62 9 years ago)
How To Save Person Stitch In Ambition 1.0
How Do I save a personal stitch on my Ambition 1.0. I can only save in sequencing.
How Do I save a personal stitch on my Ambition 1.0. I can only save in sequencing.
(Posted by myrl 9 years ago)
Pfaff Ambition 1.5
Hello, I have the Pfaff Ambition 1.5 but all the text in the display is in Italian. I would like to ...
Hello, I have the Pfaff Ambition 1.5 but all the text in the display is in Italian. I would like to ...
(Posted by acewitten 10 years ago)