2003 Mazda B3000 Support Question
2003 Mazda B3000 Support Question
Find answers below for this question about 2003 Mazda B3000.Need a 2003 Mazda B3000 manual? We have 1 online manual for this item!
Question posted by skisl on February 7th, 2014
How To Remove Headlamp Assembly On Mazda 2003 B3000
The person who posted this question about this Mazda automobile did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Manual Pages
Owner's Manual - Page 39
...the full upright position, past detent, to turn on your authorized Mazda dealer. Lights
High beams After turning the headlamps on, push the lever toward you to deactivate.
DIM
39 Move ...adjust the intensity of your headlamps should be checked by your vehicle are properly aimed at the assembly plant. If your vehicle has been in the vehicle during headlamp and parklamp operation.
Flash...
Owner's Manual - Page 40
... and pattern and safe visibility. NOTE: The correct bulbs will not damage the lamp assembly or void the lamp assembly warranty and will provide quality bulb burn time.
40
COURTESY/READING LAMPS (IF EQUIPPED)... up until the courtesy lamps come on the dome lamp to either the left turn signal. Headlamp bulbs must be turned on by moving the switch on . • the remote entry controls...
Owner's Manual - Page 41
...Mazda dealer. Your Mazda dealer has the proper tools, training and parts to perform this , vistit your dealer. To replace all instrument panel lights - If you have difficulty with this task. Replacing the interior bulbs Check the operation of bulbs Trade number Park/turn lamps 2 3157 AK (amber) (front) Headlamps...in color except where noted. Replacing headlamp bulbs NOTE: The procedure can ...
Owner's Manual - Page 42
... lamp assembly.
42 Without turning, remove the old bulb by the flying glass. Lights
WARNING: Handling Halogen Bulbs: When a halogen bulb breaks, it is touched with bare hands, body oil could cause the bulb to overheat and explode when lit. These bulbs contain pressurized gas. Keep the ring to release the headlamp assembly from...
Owner's Manual - Page 43
... 1. At the back of the bulb into the plastic base until you should be cleaned with two retainer pins. 5. You may need to release the headlamp assembly from your hands could cause the bulb to align the grooves in the plastic base with the tabs in the lamp...
Owner's Manual - Page 44
... clockwise. 8. Install the headlamp on lamp assembly. 10. Install screw(s) on vehicle, push rearward and secure with two retainer pins.
44 Disengage lamp assembly (it has a snap fit).
5. Install the bulb socket in the new bulb. 7. Align the lamp on the vehicle and push to snap in place. 9. Remove screw(s) from lamp assembly. 6. Lights
3. Rotate...
Owner's Manual - Page 45
...same portion of the socket and push in the new bulb. 5. Remove the four screws and the lamp assembly from the fog lamp bulb.
3. Install the bulb socket in the... electrical connector from vehicle.
3. Follow the same steps to expose the lamp assemblies. 2. Rotate bulb socket counterclockwise turn and remove from the fog lamp by turning clockwise. 6. Open the tailgate to replace ...
Owner's Manual - Page 46
... bulbs: 1. Pull out the old bulb from vehicle. 2. Remove the bulb socket from lamp assembly by rotating clockwise. 2. This procedure covers the high-mount brake lamp bulb. Remove the two screws and lamp assembly from socket and push in the new bulb. To remove the brake lamp assembly: 1. Lights
Replacing high-mount brake lamp and cargo...
Owner's Manual - Page 64
... a coded key programmed to your vehicle is on. If a problem occurs, turn off , remove all objects on the key chain away from touching the coded key while starting problems and a ... steadily when the ignition is an engine immobilization system. If a problem occurs with non-Mazda aftermarket remote start systems. Use of eight keys can program the keys yourself. SECURILOCK PASSIVE...
Owner's Manual - Page 71
... the risk of injury in a passenger front seat. To unfasten, push the release button and remove the tongue from the buckle. Vehicle sensitive mode This is not available on the driver safety belt...mode, which allows free shoulder belt length adjustment to your movements and locking in response to remove any slack in the vehicle are combination lap and shoulder belts. The belt will lock to ...
Owner's Manual - Page 76
...safety belt is too short for you when fully extended.
Seating and Safety Restraints
Safety belt extension assembly If the safety belt assembly is too short for you , even when fully extended, 20 cm (8 inches) can be added to .... The safety belt warning light and warning chime turn off .
76 Safety belt extension assemblies can be obtained from your authorized Mazda dealership.
Owner's Manual - Page 81
... not. Seating and Safety Restraints
NOTE: If unsure about the proper procedures, bring your vehicle to an authorized Mazda dealership for child safety seats on seatback (if equipped), child safety seat tether bracket assemblies (if equipped), LATCH child seat tether anchors and lower anchors (if equipped), and attaching hardware, should be inspected...
Owner's Manual - Page 88
...collision. WARNING: Unless serviced, the system may not function properly in OFF position while removing OFF the key. 3. ON 2. Air bags MUST BE disposed of safety belt pretensioners, air ...bags, or air bag equipped vehicles, see your authorized Mazda dealership immediately. Seating and Safety Restraints
If any of these things happen, even intermittently,...
Owner's Manual - Page 89
...a person who meets the requirements stated either in Category 1, 2 or 3 of the switch, always remove the ignition key from the passenger air bag ON/OFF switch. WARNING: In order to avoid inadvertent...and the ignition switch is ON, have the passenger air bag switch serviced at your authorized Mazda dealership immediately. ON OFF 2. Seating and Safety Restraints
WARNING: If the OFF light fails ...
Owner's Manual - Page 120
Turn the ignition to the LOCK position and remove the key whenever you move unexpectedly and injure someone. Additionally, whenever the battery is ... or durability of the vehicle. If you do not hold the brake pedal down while you leave your authorized Mazda dealership.
This feature is installed, the strategy must relearn. To put your vehicle may move the gearshift lever from...
Owner's Manual - Page 139
... case fluid loss, damage to the driveshaft and internal transmission and transfer case components. Improper removal/installation of 80 km (50 miles). • Do not exceed 56 km/h (35 ...in the forward position to the internal transfer case components. Mazda recommends the driveshafts be exceeded, you must be removed/installed only by a qualified technician. CAMPER BODIES Your pickup...
Owner's Manual - Page 152
... as required. Conventional spare tire information If you find a leak or other tires on the side of your tires. Do not remove the cooling system cap when the engine and radiator are hot, scalding coolant and steam may compromise the integrity of the road. .... If it cool. 5. If this does not lower the temperature, stop the engine and call an Authorized Mazda dealer.
Owner's Manual - Page 153
When connecting the jack handle, assemble the following locations: Tool Spare tire Jack, jack handle, wheel nut wrench Location Under...In the glove box
Key, spare tire lock (if equipped)
Removing the spare tire
1. To assemble, slide parts together. To disconnect, depress button and pull apart. • one typical extension. Assemble the jack handle to the lug wrench as shown in the ...
Owner's Manual - Page 157
... Nm (100 lb-ft). Unblock the wheels. 157 Use only Mazda recommended (1/2-20) 5 2 replacement fasteners. 11. Replace the flat tire with the lug wrench. 8. Remove the jack and fully 1 tighten the lug nuts, in the ...lug wrench. It is fastened so it does not rattle when you can be injured. 7. Remove the wheel lug nuts with the spare tire, making sure the valve stem is snug against ...
Owner's Manual - Page 173
... 03 9999 95 023C 03 PUBLICATION DESCRIPTION 2003 WORKSHOP MANUAL 2003 WIRING DIAGRAM 2003 OWNER'S MANUAL
WORKSHOP MANUAL: Covers recommended maintenance and repair procedures of our publications through an Authorized Mazda Dealer, refer to correctly and safely maintain Mazda vehicles. 173 SERVICE PUBLICATIONS Factory-authorized Mazda service publication are available for the entire electrical...
Similar Questions
My 2003 B3000 Mazda Pickup
My mazda will not rev past 3000 rom in idle, and stutters when accelerating. I have changed plugs, w...
My mazda will not rev past 3000 rom in idle, and stutters when accelerating. I have changed plugs, w...
(Posted by Ci102mp 10 years ago)