Maytag MVWC300XW Support Question
Maytag MVWC300XW Support Question
Find answers below for this question about Maytag MVWC300XW.Need a Maytag MVWC300XW manual? We have 5 online manuals for this item!
Question posted by scotland03 on October 12th, 2012
Drain Problem
Ran load on "BULKY" setting but when drain cycle kicked in, it remains ON constantly. All control panel LED lights are OFF and will not come on even when the machine is unplugged then re-plugged to power.
Current Answers
Related Maytag MVWC300XW Manual Pages
Installation Instructions - Page 2
...Drain hose too short
Extension Drain Hose Part Number 285863 Connector Kit Part Number 285835
Lint clogged drain
Drain Protector Part Number 367031 Connector Kit Part Number 285835
LOCATION REQUIREMENTS
Select proper location for installation are in cardboard insert in a basement, laundry...couplings (2 pack)
Alternate parts: (Not supplied with washer)
Adjustable or open end wrench 9/16" (14...
Installation Instructions - Page 3
... spacing of washer. Consider allowing more than 96" (2.44 m), you need :
n A water heater set to reduce noise transfer.
Top of drain hose should be at least 39" (990 mm) above floor; n Floor must install higher than 4.5" (113 mm) of laundry tub must be inside standpipe or below 32° F (0° C). Wall standpipe drain system
14...
Installation Instructions - Page 5
... to step 6. For a laundry tub or standpipe drain, go to remove all parts from rear panel. Gently place power cord over console to allow free access to move washer later.
4. IMPORTANT: 4.5" (113 mm) of laundry tub. Attach drain hose to free from tray. NOTE: Keep tray in place on bottom of laundry tub. Free power cord
If clamp is...
Installation Instructions - Page 6
... is seated on water faucets to check for a few seconds through hoses into a laundry tub, drainpipe, or bucket to a cold water faucet, you must use a Y-adapter...faucet. IMPORTANT: Do not overtighten or use old hoses. In most standard configurations, hoses will drain later.
6 Repeat with flat washers (not provided). n Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or...
Installation Instructions - Page 7
..." or 14 mm open -end or adjustable wrench to raise the washer.
Not Level
LEVEL
Not Level
7
Check levelness of sides. Rock washer back and forth to prop washer with beaded tie strap. HELPFUL TIP: You may want to laundry tub leg, drain standpipe, or inlet hoses for wall standpipe with wooden block. Tighten leveling...
Dimension Guide - Page 1
... a standpipe drain: 2" (51 mm). This washer has been tested for ease of washer. IMPORTANT: To avoid siphoning, no higher than 96" (2.44 m) from bottom of laundry tub must... clearances for planning purposes only.
Top-Loading Washer
PRODUCT MODEL NUMBERS
MVWC200X, MVWC400X, MVWC450X, MVWX500X, MVWX600X, MVWX700X, MVWC300X, MVWX550X
Washer dimensions
OVERALL DIMENSIONS
271/2"
27"
(...
Energy Guide - Page 1
... will depend on your utility rates and use.
• Cost range based only on standard capacity models. • Estimated operating cost based on eight wash loads a week and a 2007
national average electricity cost of 10.65 cents per kWh and natural gas cost of this label before consumer purchase. U.S.
Clothes...
Warranty Information - Page 1
... and exclusions may not apply to repair or replace appliance light bulbs, air filters or water filters. You will pay...an authorized Maytag servicer is not available.
9.
MAYTAG® LAUNDRY WARRANTY
LIMITED WARRANTY
For one year from the date of ...service under this limitation may not apply to resolve the problem
after checking "Troubleshooting," additional help you obtain assistance or...
Use & Care Guide - Page 3
... correct water level for clothes to traditional top-load washers. There will begin the sensing process to be above the water line. Concentrated Cleaning
Low-water cleaning means concentrated cleaning. The lower water level combined with dirty laundry, fill it is needed.
INTELLIFILL™ Water Level Control
Once you may hear sounds and noises...
Use & Care Guide - Page 4
... "Cycle Guide" for the load. press again to "Yes" if adding fabric softener. Appearance may hear the hum of fabric and soils being washed. If the washer has been paused the "wash" status light will first perform a self-test on the type of these spins. SENSING
When the START/Pause/Unlock button is restarted. CONTROL PANEL...
Use & Care Guide - Page 5
... this stage. The motor sounds may take several second pause. For cycles that use the extra rinse option, you will come on the load size. Fabric softener will partially fill the washer and then begin to have the sensing light on the selected cycle and spin speed.
Concentrated cleaning delivers the detergent directly to resume the...
Use & Care Guide - Page 6
... indicating "Machine Washable Silks" or "Gentle" cycle on all models. Use this cycle to shorten drying times for lightly soiled mixed loads.
Select Fabric Softener Added-Yes if using fabric softener. Select Fabric Softener Added-Yes if using fabric softener. N/A
High This cycle uses a spin to drain
washer after cancelling a cycle or completing a cycle after power interruption...
Use & Care Guide - Page 7
...cycle, water temperature, and colorfastness.
• Separate heavily soiled items from lightly soiled.
• Separate delicate items from sturdy fabrics.
• Do not dry garments if stains remain after washing, because heat can set stains into the bottom of the washer basket before adding clothes.
If using an Oxi or color-safe bleach laundry...-resistant items, load evenly.
• Use ...
Use & Care Guide - Page 8
... around the agitator; See max fill line arrows. Items need to move freely for correct amount of the rim. For more than 1 cup (250 mL). Load laundry into washer. load them in cycle.
6. For best results, do not pack the load tightly. IMPORTANT: Fabric Softener Added option must be selected to "Yes" to choose your...
Use & Care Guide - Page 9
...Light soils
Cold
This is normal operation.
9 Promptly remove garments after cycle has completed to avoid odor, reduce wrinkling, and rusting of the spin prior to your load. the lid will light. This is the temperature from your previous washer.... If your hot water heater setting.
Unlocking the lid to check for several minutes if the load was spinning at high speed. ...
Use & Care Guide - Page 11
... and drain any remaining water into basket opening. Drape power cord over lid and down front of washer.
Shut off both water faucets.
2. Unplug power cord.
5. Place inlet hoses and drain hose inside washer. Run washer through the following recommended procedure:
To use , vacation, winter storage, or moving .
3. Place packing tray from back of detergent for a medium-size load...
Use & Care Guide - Page 12
.... Humming
Sensing light is added to basket could fall between basket and tub or may block pump.
Water Leaks
Check the following for leaks or clogged sink or drain. Fill hose washers.
Do not place tape over drain opening. Check all four fill hose flat washers are removed during the Drain & Spin cycles. The washer senses load sizes and...
Use & Care Guide - Page 13
...) (cont.)
Washer not draining/ spinning, loads are still wet, or spin light remains on your garment.
Cycles with lower spin speeds remove less water than 96" (2.4 m) above the floor.
See "Using Your Washer" for balanced spinning. Lower drain hose if the end is balanced. Do not add detergent.
13
The washer may be tightly packed or unbalanced. Plug power cord into...
Use & Care Guide - Page 14
....
Remove any kinks in loose heaps evenly around the basket wall. however, items will be on load after cycle
High speed spins extract more moisture than traditional top-load washers. http://www.maytag.com/help -
Load garments in hoses. Energy-saving controlled wash temperatures.
Both hot and cold water faucets must be attached and have both...
Use & Care Guide - Page 15
... heaps evenly around the basket wall. Odors
Lid locked light is tightly packed. Items may have been added incorrectly. Fabric damage can keep washer from operating correctly. Garment care instructions may have been damaged before starting a cycle.
Tie all strings and straps before washing. Load garments in the fabric softener dispenser. Do not pour...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
The cycle time is not correct - Bravos washer with agitator
... to redistribute the laundry load in the suds to spin out water. Top-load washer Not spinning out enough water - If the code remains and wash cycle dial is detected, then the washer will make several times to aid in future loads to zero at one value for a long time? Does this problem. There is using less... -
The cycle time is not correct - Front-load washer
...-sudsing, always use in the drum; this problem. Consider adding more likely to the cycle. Are you see "Sud" and the Done status light is not able to aid in the window? Front-load washer Why is detected, the washer will glow while the washer is HE High Efficiency detergent the only type... -
The cycle time is not correct - Top-load HE washer with Dispensers in Corners
...and washer is not correct - The Estimated Time Remaining is based on your desired cycle using cold water. Press Start. Do not add detergent. During this problem. Top-load washer with a single or bulky item...the suds. If the code remains and wash cycle dial is flashing, reselect your washer may occur several attempts to redistribute the laundry load in the suds to ...
Similar Questions
Cu Ft For My Maytag Washer,model# Mhwe450ww02 Front Load Washer
Hi, I want to know cu ft for my Maytag washer,Model# mhwe450ww02 front load washer
Hi, I want to know cu ft for my Maytag washer,Model# mhwe450ww02 front load washer
(Posted by rashmi3462 8 years ago)
Does Maytag Centennial Washer Mvwc300xw Need High Efficiency Detergent?
(Posted by Johabi 9 years ago)
Washer Is Stuck In A Drain Cycle How Do I Reset I Cannot Clear It
washer is stuck in a drain cycle how do I reset? I cannot clear it seems to need to be resent i ha...
washer is stuck in a drain cycle how do I reset? I cannot clear it seems to need to be resent i ha...
(Posted by jnd914 11 years ago)