Maytag MEDZ400TQ Support Question
Maytag MEDZ400TQ Support Question
Find answers below for this question about Maytag MEDZ400TQ - 27-in Epic Series Electric Dryer.Need a Maytag MEDZ400TQ manual? We have 2 online manuals for this item!
Question posted by Anonymous-27805 on April 27th, 2011
Power Went Out Now Maytag Epic Dryer Wont Come , Has Power Inside ,wont Come On
A TREE FELL ON OUR POWER LINE AND THE DRYER WAS ON WHEN THE POWER WENT OUT NOW IT WILL NOT START .. IT HAS POWER TO THE LIGHT BUT WHEN I HIT THE START BUTTON NOTHING HAPPENS , IVE TRIED TO RESET IT AND FLIP ALL THE BREAKERS A COUPLE OF TIMES AND STILL NOTHING I DONT HAVE A VOLT METER SO I CANT CHECK ANYTHING .. :-(
Current Answers
Related Maytag MEDZ400TQ Manual Pages
Use and Care Guide - Page 5
...(91.4 cm)
*28.65" (72.77 cm)
27" (68.6 cm)
*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for this dryer. The combined weight
of a companion appliance should also be...that allows for a garage installation. Contact your dryer at least 18 inches (46 cm) above the floor.
If using a power supply cord, a grounded electrical outlet located within 2 ft
(61 cm) ...
Use and Care Guide - Page 7
...dryer, you must be used , it here.
■ This dryer... using a power supply cord:
Use a UL listed power supply cord... only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply...Electric Code requires a 4-wire power supply connection for homes built after 1996, dryer circuits involved in .2 * (155 cm2)
3"* (7.6 cm)
1"* (2.5 cm)
6"* (15.2 cm)
72" (182.9 cm)
5 14 cm)
1" (2.5 cm)
27...
Use and Care Guide - Page 8
... UL listed strain relief. GROUNDING INSTRUCTIONS
■ For a grounded, cord-connected dryer: This dryer must be grounded. grounding conductor can result in doubt as to the equipment-grounding terminal or lead on the power supply cord: if it will reduce the risk of electric shock by a white cover. If connecting by a qualified electrician. In...
Use and Care Guide - Page 9
...of the line.
Electrical Shock Hazard
Plug into a standard 14-30R wall receptacle. A copy of electric shock by...electric shock. The cord is properly installed and grounded in conformance with a cord having an equipmentgrounding conductor and a grounding plug.
Connect to whether the dryer is recommended. SAVE THESE INSTRUCTIONS
4-wire receptacle 14-30R
■ Do not use Power...
Use and Care Guide - Page 10
...
D
B. Install strain relief. Hole below the terminal block opening
C
C. U.S.A. Use a UL listed strain relief.
Fire Hazard
Use 10 gauge solid copper wire. Disconnect power before making electrical connections.
A
A.
Center, silver-colored terminal
block screw
B
D. Strain relief tab pointing up and the other is pointing up
B
B.
Terminal block cover and hold in...
Use and Care Guide - Page 11
...neutral wire, go to Section
4-wire connection: Power supply cord
C
A. Removable conduit connector B. Hole below the terminal block opening.
Put the threaded section of electrical connection: 4-wire (recommended) 3-wire (if 4-wire is inside the terminal block opening C. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Style...
Use and Care Guide - Page 12
... UL listed strain relief
5. Direct wire cable must have completed your electrical connection. 4-wire connection: Power supply cord
IMPORTANT: A 4-wire connection is required for mobile homes ...dryer can be moved if needed.
12 Now go to center silvercolored terminal block screw. Ground prong D. Ring terminals
1.
Connect the other wires to external ground conductor screw. Dotted line...
Use and Care Guide - Page 13
... of power supply ... Tighten strain relief screw. Secure cover with hold-
You have completed your electrical connection. A. Neutral ground wire D. B
A C
A. Ground wire (...12.7 cm). Center silver-colored terminal block screw E. E
7. Dotted line shows position of the terminal block. Neutral wire (white or center ... (green or bare) of wires into slot of dryer rear panel. A
D
E
(12.75c"m)
...
Use and Care Guide - Page 14
... the terminal block, place the hooked end of the wire under the screw of dryer rear panel. You have 5 ft (1.52 m) of the terminal block. Now go...Power supply cord
Use where local codes permit connecting cabinet-ground conductor to the center, silvercolored terminal screw of extra length so dryer can be moved if needed. Tighten screw. Direct wire cable must have completed your electrical...
Use and Care Guide - Page 15
...neutral wire (white or center wire) of dryer rear panel. C A
B
D
E
Optional 3-wire connection
Use for direct wire or power supply cord where local codes do not permit... connecting cabinet-ground conductor to "Venting Requirements." Neutral ground wire
C. You have completed your electrical connection. Grounding path ...
Use and Care Guide - Page 16
....
■ Replace any gas vent, chimney, wall, ceiling or a concealed space of fire, this dryer MUST BE EXHAUSTED OUTDOORS. Clamp
4" 10.2 cm
4" (10.2 cm) heavy metal exhaust vent
Vent ...
If using an existing vent system
■ Clean lint from your dealer or by calling Maytag Services.
For more information, see the "Assistance or Service" section.
16 Venting Requirements
WARNING
...
Use and Care Guide - Page 18
... securely fastened to a noncombustible portion of vent material and hood combinations acceptable to have the dryer converted. Two closeclearance installations are available for best drying performance
■ Use the following kits for close clearances
Venting systems come in the Vent system chart.
Select the type best for mobile home installations
The exhaust...
Use and Care Guide - Page 19
..., prop up . Slide the dryer on the cardboard. If connecting to do so can result in the flexible gas line. 4. Move dryer into its final location. Once the...
27 ft (8.2 m)
21 ft (6.4 m)
Flexible metal
23 ft (7 m)
15 ft (4.6 m)
2. Place a carton corner post from the dryer carton. Use a wrench to dryer location. See "Determine vent path" in dryer. The dryer vent must fit inside ...
Use and Care Guide - Page 22
... and close the door. Complete Installation
1. See "Level Dryer." 5. In the U.S.A.
■ For power supply cord installation, plug into a grounded 4 prong outlet. When the dryer has been running or "On" position.
■ Start button has been pushed firmly.
■ Dryer is plugged into an outlet and/or electrical supply is level. If there is first heated. NOTE...
Use and Care Guide - Page 23
Place laundry into dryer and shut door. 3.
Do not dry anything that has ever had anything that has ever ... information. WARNING: To reduce the risk of fire, electric shock, or injury to follow these basic steps to specific sections of oil on it (even after washing). Please refer to start your dryer. Press POWER.
23 Failure to follow these instructions can completely remove ...
Use and Care Guide - Page 25
...remove the load from the dryer as soon as tumbling stops. If a Timed Dry Cycle is opened, and then the light will come on . Drying tips ...Laundry cools for ease in the cycle. This indicator stays on the load size and dryness level. NOTE: You cannot use the Dryness Level with the drying Status indicator lights. NOTE: You cannot use the Timed Dry Cycle Adjust Up or Down arrow buttons...
Use and Care Guide - Page 28
... (see following table.
8. Press (and hold START to the front page of this manual or contact the dealer from whom you happen to secure over the edge of items that can...Press the POWER button.
6.
To find out whether your dryer. To use Sensor Dry cycles with the drying rack. Place dryer rack inside dryer drum, positioning the back wire on the amount of the inner dryer back panel...
Use and Care Guide - Page 30
... breakers for the dryer. Electric dryers use ?
If you should:
1. WARNING
Moving care
For power supply cord-connected dryers: 1. Clean lint screen. Dryer Operation
Dryer will be turning, but you are intact and tight, or that both fuses are at home. Use a time-delay fuse.
■ Is the dryer door firmly closed?
■ Was the Power button firmly pressed? Unusual...
Use and Care Guide - Page 31
...items and restart the dryer. Dryer displaying code message
■ "PF" (power failure), check the following: Was the drying cycle interrupted by a power failure? Dryer Results
Clothes are not ...START to do not feel air movement, clean exhaust system of dryer cycles requires temperatures above the floor for the types of the dryer requires 5" (12.7 cm). Do not use a plastic vent. Run the dryer...
Use and Care Guide - Page 32
... area, call . Our consultants provide assistance with :
Call the Maytag Services, LLC Customer Assistance toll free: 1-800-688-9900.
■ Features and specifications on our full line of the cycle? ■ Was the dryer overloaded? Whirlpool Canada LP designated service technicians are gone from dryer at :
Customer Interaction Centre Whirlpool Canada LP 1901 Minnesota...
Maytag Knowledge Base Results
We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!-
Dryer does not heat - Electric dryer
... heat - Electric dryers use 2 household fuses or circuit breakers. Electric dryer My electric dryer does not heat. Expect loads dried with the other temperature selections. Gas dryer FAQs Knowledgebase search tips My dryer will not start Damp loads or long drying times - Did you may be turning, but you recently install a power supply cord on the control knob or button with... -
Recall Information
... check ... cribs, power tools,...Series Toaster 2005 - brand dishwashers with protecting the public from unreasonable risks of injury or death from products that pose a fire, electrical...Dryer 2002 - Consumers should immediately stop using the recalled dishwashers, disconnect the electric supply by shutting off the fuse or circuit breaker...label located inside the plastic... number STARTING with ... -
Refrigerator not operating
... the light comes back on , check the following. Side by side refrigerator Refrigerator or freezer not cool enough - Close and re-open for the temperature of the refrigerator and contents to completely cool. Side by side refrigerator Refrigerator or freezer not cold enough No lights inside refrigerator - Check that outlet? Cooling On/Off button on control...
Similar Questions
Dryer Doesn't Start On Sensor Dry
My dryer will start on timed dry only if I push on the cycle knob. Will not work on sensor dry or ti...
My dryer will start on timed dry only if I push on the cycle knob. Will not work on sensor dry or ti...
(Posted by collinss72 8 years ago)
Maytag Epic Dryer Has Power Wont Start
(Posted by mikedan 9 years ago)
Hello. My Dryer Does Not Start.
My dryer has two years . I push the start button and it does not start but it make a sound as is on ...
My dryer has two years . I push the start button and it does not start but it make a sound as is on ...
(Posted by schm 10 years ago)
My Dryer Has Power, But Will Not Turn On.
(Posted by judmaxpi 12 years ago)
Maytag Medz400tq1 Error Code
My dryer will not start. When Power switch pressed and held for 1 sec, all indicators appear normal ...
My dryer will not start. When Power switch pressed and held for 1 sec, all indicators appear normal ...
(Posted by jim68012 12 years ago)