Home » Maytag » Laundry Dryers » Maytag MEDC400VW

Maytag MEDC400VW Support Question

Find answers below for this question about Maytag MEDC400VW - Centennial Electric Dryer.
Need a Maytag MEDC400VW manual? We have 2 online manuals for this item!

Maytag Overview Questions Manuals Reviews Videos Research

Question posted by colapkdla on February 2nd, 2014

How To Replace Belt To A Maytag Centennial Electric Dryer

The person who posted this question about this Maytag product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Maytag MEDC400VW Manual Pages

Owners Manual - Page 2

The dryer must conform with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70. 2 IMPORTANT: The gas installation must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54.

Owners Manual - Page 3

... 2 years. The venting system attached to the dryer plays a big role in good air flow. ■■ Replace plastic or foil vent material with heat, dryers require good air flow to do not use .... Failure to follow the "What to efficiently dry laundry. WARNING: For your safety, the information in this or any electrical switch; WARNING: Gas leaks cannot always be paid by UL or CSA...

Owners Manual - Page 6

... selector is set it to complete drying, if needed. To stop your dryer has a Temperature selector, set to the recommended cycle for clothes to remove a load from the dryer as soon as it stops. 6. (OPTIONAL) Your dryer may have all of fire, electric shock, or injury to purchase one for temperature suggestions. Place drying...

Owners Manual - Page 7

... the lint screen toward you have a gas dryer, close shutoff valve in front of clean cloths or towels to both sides of clothes. Replace screen in the door of time, you should...dryer and fabrics. ■■ If lint falls off the screen with your fingers. 2. Every Load Cleaning Style 1: 1. Push the lint screen firmly back into place. 2. This includes clearing piles of laundry...

Owners Manual - Page 8

...; Has a household fuse blown, or has a circuit breaker tripped? The dryer may not have heat. Electric Dryers For power supply cord-connected dryers: 1. For direct-wired dryers: WARNING 3. Open the dryer door. Using a Phillips head screw driver, remove the screw located in dryer base. 4. Remove the cover. Replace all parts and panels before servicing. Close shutoff valve in...

Owners Manual - Page 9

... will increase drying times. Run the dryer for the types of dryer cycles requires temperatures above 45ºF (7ºC). ■■ Is the dryer located in a cycle. Long venting will change the amount of lint or replace exhaust vent with lint? Separate the load to move and install dryer. Lint screen should be cleaned before...

Owners Manual - Page 10

...door Drying rack - Allow the Cool Down cycle to finish before removing laundry from the dryer before Cool Down may have an odor. Items removed before the end of the cycle? ■...9632; Was the load removed from the area, rewash, and dry the clothing. ■■ Is the electric dryer being used ? fits 29" (737 mm) Super Capacity, 6.5 cu. Loads are cooled slowly to reduced wrinkling and...

Owners Manual - Page 11

...with electrical or plumbing codes, or use or when it is installed in an inaccessible location or is not installed in accordance with Maytag's ... repair labor to correct defects in your major appliance, to replace or repair house fuses, or to correct house wiring or... for future reference. You must be easily determined. MAYTAG® LAUNDRY WARRANTY LIMITED WARRANTY For one year from the date ...

Installation Instructions - Page 1

... la puerta. All safety messages will tell you what can be killed or seriously injured if you don't follow instructions. U.S.A. DRYER SAFETY Your safety and the safety of others . 29" (73.7 CM) ELECTRIC DRYER INSTALLATION INSTRUCTIONS INSTRUCTIONS POUR L'INSTALLATION DE LA SÉCHEUSE ÉLECTRIQUE DE 29" (73,7 CM) Table of injury, and...

Installation Instructions - Page 2

...ºF (7ºC). Drying times can result in garages, closets, mobile homes or sleeping quarters. Check that connect to the dryer must not be considered. ■ A level floor with a maximum slope of the dryer. If using a power supply cord, a grounded electrical outlet located within 2 ft (61 cm) of either side of 1" (2.5 cm) under entire...

Installation Instructions - Page 3

... the exhaust vent with equivalent ventilation openings are acceptable. ■ Companion appliance spacing should be considered for homes built after 1996, dryer circuits involved in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition and all local codes and ordinances. Recommended spacing should also be considered on all mobile home...

Installation Instructions - Page 4

...) Then choose a 4-wire power supply cord with ring or spade terminals and UL listed strain relief. SAVE THESE INSTRUCTIONS 4 Electrical Connection To properly install your dryer, you must determine the type of electrical connection you are in doubt as to the equipment-grounding terminal or lead on the power supply cord: if it...

Installation Instructions - Page 5

... International Certified Power Cord intended to an individual branch circuit. 4-wire receptacle 14-30R ■ Do not use Power Supply Cord Replacement Part Number 3394208. Electrical Requirements - Failure to whether the dryer is equipped with a qualified electrician or service representative or personnel if you use an extension cord. A time-delay fuse or circuit...

Installation Instructions - Page 6

...or bare wire) must be connected to do so can result in death, fire, or electrical shock. Failure to green ground connector. Failure to remaining 2 terminals (gold). Disconnect power.... E. Connect remaining 2 supply wires to do so can result in place. Securely tighten all electrical connections. Only Power Supply Cord Direct Wire WARNING WARNING Fire Hazard Use a new UL listed ...

Installation Instructions - Page 7

...) A fused disconnect or circuit breaker box* A UL listed, 120/240-volt minimum, 30-amp, dryer power supply cord* 4-wire connection: Direct Wire 3-wire connection: Power supply cord 3-wire direct 3¹...conduit connector onto the strain relief threads. Ring terminals 4. Put the threaded section of electrical connection: 4-wire (recommended) 3-wire (if 4-wire is inside the terminal block ...

Installation Instructions - Page 8

Tighten screw. Direct wire cable must have completed your electrical connections. Cut 1¹⁄₂" (3.8 cm) ... terminal block screw C. Neutral wire (white or center wire) D. ¾" (1.9 cm) UL listed strain relief E. Dotted line shows position of dryer rear panel. A B FE D A. Secure cover with hold-down screw. 7. Neutral wire (white or center wire) D. ¾" (1.9 cm...

Installation Instructions - Page 9

... of the terminal block. Tighten strain relief screws. 6. Neutral ground wire B. You have completed your electrical connections. If using 3-wire cable with ground wire, cut bare wire even with up turned ends ...connecting cabinet-ground conductor to the terminal block, place the hooked end of dryer rear panel. Spade terminals with outer covering. Center silver-colored terminal block...

Installation Instructions - Page 10

... end together. Center silver-colored terminal block screw D. You have completed your electrical connections. Neutral ground wire C. Secure cover with hold -down screw. 6. Connect neutral ... screw D. Remove center silver-colored terminal block screw. 2. Place the hooked ends of dryer rear panel. Grounding path determined by a qualified electrician 3. Loosen or remove center silver-...

Installation Instructions - Page 11

... any plastic or metal foil vent with lint. ■ Replace any gas vent, chimney, wall, ceiling or a concealed space of the Dryer User Instructions. Do not use duct tape. Failure to avoid... Vent material ■ Use a heavy metal vent. Louvered hood style B. If this dryer MUST BE EXHAUSTED OUTDOORS. DURASAFE™ venting products are shown here. Clamp Exhaust Recommended ...

Installation Instructions - Page 15

... cord installation, plug into an outlet and/or electrical supply is on. ■ Household fuse is intact and tight, or circuit breaker has not tripped. ■ Dryer door is first heated. Remove the blue protective ...power. Be sure the vent is still no heat, contact a qualified technician. See "Level Dryer." 6. If you feel heat, cancel cycle and close the door. Check that both fuses ...

Maytag Knowledge Base Results

We have determined that the information below may contain an answer to this question. If you find an answer, please remember to return to this page and add it here using the "I KNOW THE ANSWER!" button above. It's that easy to earn points!

Dryer does not heat - Electric dryer
Did you may not have heat. Replace the fuses or reset the circuit breakers. If the problem continues, call an electrician. Gas dryer FAQs Knowledgebase search tips My dryer will not start Damp loads or long drying times - Electric dryer My electric dryer does not heat. Enter Model Number How do I find my model number? The drum may...
Display shows L2 - Dryer
...dryer have heat. The power supply cord may be a problem with your dryer. If the dryer has heat, disregard the L2 code on the dryer? Electric dryer Dryer... heated cycle, and restart the dryer. If the problem continues, call an electrician. The ... home power supply keeping the dryer's heater from turning on, even if the dryer drum is turning and the load...
My dryer or load has an odor
...and dry the load. The odor will result in the washer or dryer? Is the dryer being used for a long time will begin to grow mildew, which will be gone ...dryer. If so, ventilate the area. When odors or fumes are gone from the washer at the end of the wash cycle to avoid odors. Was a damp or wet load left in the washer or dryer for the first time? (Electric dryers) A new electric...