Makita LS1216L Support Question
Makita LS1216L Support Question
Find answers below for this question about Makita LS1216L.Need a Makita LS1216L manual? We have 4 online manuals for this item!
Question posted by spvremodeling on April 30th, 2014
Blue Blade Protector
Blade cover wont retract when i pull handle down to cut . Saw was dropped and I think some sort of l shape bracket was busted Im trying to order part but dont know what it is
Current Answers
Related Makita LS1216L Manual Pages
Owners Manual - Page 2
...
Model Blade diameter Hole diameter Max. Cutting capacities ...(H x W)
Miter angle
0°
Thickness of wood facing
20mm (13/16") 38mm (1-1/2")
45°(left and right)
Thickness of wood facing
15mm (9/16") 25mm (1")
52°(left and right)
Thickness of wood facing
15mm (9/16") 25mm (1")
60°(right)
Thickness of wood facing
15mm (9/16") 25mm (1")
LS1216/LS1216L...
Owners Manual - Page 3
... checking to EPTA-Procedure 01/2003
For Your Own Safety Read Instruction Manual
USA007-2
Before Operating Tool
Save it was not designed.
10. KNOW YOUR POWER TOOL. KEEP CHILDREN AWAY.
Do not use face or dust mask if cutting operation is recommended. Form habit of research and development, the specifications herein are NOT safety...
Owners Manual - Page 4
...tool until it comes to install the proper outlet. To reduce the risk of power and overheating. This plug will cause a drop...of saw if blade guard does not move freely and close instantly. DIRECTION OF FEED. NEVER LEAVE TOOL ...saw without guards in good condition. Serious injury could occur if the tool is tipped or if the cutting tool is in place. VOLTAGE WARNING: Before connecting the tool...
Owners Manual - Page 5
..., return carriage to clean blade.
13. Keep cord away from tool, then cleaning it will not move during a cutting operation and the saw to stop before moving portions...the handle firmly. Make sure the shaft lock is called cross-armed cutting and exposes user to cut , KICKBACK can result. Follow material supplier safety data. This is released before changing blade ...
Owners Manual - Page 6
Complies with 21CFR 1040.10 and 1040.11 AVOID EXPOSURE-Laser radiation is emitted from this instruction manual may cause serious personal
injury.
WARNING:
MISUSE or failure to follow the safety rules stated in
this aperture
CAUTION LASER RADIATION DO NOT STARE INTO BEAM
Maximum Output LASER RADIATION IS
EMITTED FROM APERTURE. • USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF ...
Owners Manual - Page 7
... just contact the sides of a cut 6. Screw
2
1
009486
Positioning kerf board
009488
1
1 2
3 4
5
1. Blade teeth 3. Right bevel cut 5.
This tool is attempted. DO NOT DEFEAT OR REMOVE GUARD.
1. Kerf board
1. Kerf board 4. After adjusting the kerf boards, release the stopper pin and raise the handle. Lock lever 2. Straight cut . Lower the handle fully and push in the...
Owners Manual - Page 8
... holding the handle all the way down the lock lever.
Periphery of the saw blade as shown in the figure fully while supporting the weight of
blade
3. Stopper lever
009487
The lower limit position of the blade can be sure that
the blade does not contact any part of the tool counterclockwise.
Grip 3. With the tool unplugged, rotate...
Owners Manual - Page 9
...Do not use a lock with a lock-off button which prevents the tool from being pressed, tilt the carriage to raise the
handle fully. • After changing the bevel angle, always secure the
...CAUTION: • When tilting the saw blade, be sure to the right.
1. Lock-off button and pull the switch trigger. Latch lever
Slide lock adjustment
1. Any tool with an inoperative switch is HIGHLY ...
Owners Manual - Page 10
..." regarding its shifting method.
The blade brake system is factory adjusted so that the tool is positioned within 1 mm (0.04") from the side surface of the saw blade by turning it stops sliding. Laser line is not a substitute for laser
1. Refer to the left or right side of the blade (cutting position). A) When you obtain correct...
Owners Manual - Page 11
...for the arbor hole of the blade you intend to use the socket wrench to the wrench holder. Lock the handle in the stopper pin.
1
1. Blade case
4. Socket wrench
2
Press...blade guard and center cover.
1. Hex bolt
2
009495
The socket wrench is removed mistakenly, be sure
to install it on the blade case. Installing or removing saw blade
CAUTION: • Always be sure that the tool...
Owners Manual - Page 12
... of the dust bag makes cutting operations clean and dust collection easy. Release the handle from the tool and pull the fastener out. Return the cover to the original position and it near the dust nozzle on the tool. Dust box can easily be removed by pulling out while turning it locks. Saw blade 4. Inner flange 5. Hex bolt
009524...
Owners Manual - Page 13
... workpiece support, and make sure that no part of the tool, especially blade, contacts the lower and upper fences when lowering and raising the handle fully at any position and pulling or pushing the carriage all the way at the lowest position.
1
1. When bevel-cutting operations are on the inside and outside . Support workpiece over...
Owners Manual - Page 15
... injury.
15 If you perform the slide cut without pulling the carriage fully or if you fully. Slide (push) cutting (cutting wide workpieces) 1. When the cut is completed, switch off the tool and WAIT UNTIL THE BLADE HAS COME TO A COMPLETE STOP before lowering. If the handle is pressed down the handle to cut the workpiece. • Gently press down...
Owners Manual - Page 16
... come to its fully elevated position. Inside corner 2. If the blade is raised while the blade is pulled all the way back toward the operator. Then gently lower the handle to the previously covered "Adjusting the miter angle".
4. Outside corner
Fig.A
001556
(1) (2) (3) (4)
1
2
1. Miter cutting Refer to the fully lowered position while applying pressure in Fig. Bevel...
Owners Manual - Page 23
... points to 45° on the bevel scale on the left side of the saw blade
1
4
5
2
3
1. Adjusting the position of the tool and personal injury. Workpiece 2. Pulling the switch trigger accidentally cause an accidental start of laser line For model LS1216L only
1. A blow or
impact causes the incorrect position of laser line, damage to 0°...
Owners Manual - Page 24
... section titled "Installing or removing saw blade before removing the lens according to the side surface of the lens for the laser light For model LS1216L only
1. NOTE: • ...the screw
further and pull out the lens again without shifting the workpiece from the side surface of cut , return the handle to see where the cutting line and the position of the saw blade is unplugged. 2. ...
Owners Manual - Page 25
...persons. Keep the blade guard clean according to prevent rust. • When storing the tool, pull the carriage toward you...saw blades For smooth and precise cutting in the previously covered section titled "Blade guard". Slices cleanly against the grain.
Only use with machine oil to the directions in various materials. Brush holder
2
cap
009516
After replacing brushes, plug in the tool...
Parts Breakdown - Page 3
..., HM1500 HSS SCREW(FLAT POINT) M6X16, LS1016 H.S.H. SPRING 4, 2416S TAPPING SCREW 4X18, 4323K HANDLE CPL., LS1016 TAPPING SCREW 4X18, 4323K SWITCH BUTTON, LS1016 LEAD COVER HOLDER, LS1016L TAPPING SCREW 4X18, 4323K LEAD COVER, LS1216L RING SPRING 8, LS1013 PIN 6, LS1016L COMP. SPRING 7, 2414B P.H. BOLT M8X12, LS1030 BLADE CASE CPL., LS1216L BALL BEARING 608DDW, 9031
Page 3 of 7
Quantity...
Parts Breakdown - Page 4
...
2
TORSION SPRING 9, LA1013L
1
HEX. WASHER 5, HM1100C
2
COMPRESSION SPRING 7, AN621
2
F. SOCKET SET SCREW M4X6, LS1013L
1
HEX.SCREW M5X8, 4200N
2
LASER COVER, LS1216L
1
TAPPING SCREW 4X16, 9524NB
2
PROTECTOR, LS1016
1
THUMB SCREW M5X24, LS1013L
1
F. WASHER 12, HR2410
1
RUBBER WASHER12, LS1016
1
F. SCREW M5X16, 4301BV
3
BALL BEARING 608DDW, 9031
1
F. WASHER...
Flyer (English) - Page 2
...-of-cut whether blade is turning or not, with on-off switch and micro-adjustments for Devices and Radiological Health requires laser device manufacturers to keep track of end user contact information. As a result, Makita U.S.A., Inc. Shipping weight: LS1216L LS1216LX (Saw and stand)
78.0 lbs. 168.7 lbs. recommends that end users register their tool on...
Similar Questions
Plastic Blade Guard Sticks And Does Not Rise Smoothly.
How do I fix the plastic guard not rising easily without unsafely pushing down to hard on the tool. ...
How do I fix the plastic guard not rising easily without unsafely pushing down to hard on the tool. ...
(Posted by nathanseymour 7 months ago)
Blade Direction
the blade spindle spins clockwise yet the direction arrow on the saw cover and the replacement blade...
the blade spindle spins clockwise yet the direction arrow on the saw cover and the replacement blade...
(Posted by Colinboyd 7 years ago)
Guard Binds When Lowering Blade
The blade is very hard to lower for the first couple of inches, then it suddenly makes a click noise...
The blade is very hard to lower for the first couple of inches, then it suddenly makes a click noise...
(Posted by smithjran 7 years ago)
