Makita BBX7600N Support Question
Makita BBX7600N Support Question
Find answers below for this question about Makita BBX7600N.Need a Makita BBX7600N manual? We have 3 online manuals for this item!
Question posted by jimcrone on January 12th, 2014
My Makita Bbx7600 Will Only Run 1/2-3/4 Power.
Is there a way to clean or adjust the carburator?
Current Answers
Related Makita BBX7600N Manual Pages
Owners Manual - Page 2
...from your Makita Blower.
Table of Contents
Symbols 2 Safety instructions 3-5 Technical data 6 Designation of parts 7 Assembly instructions 8-9 Before starting the engine 10-11 Operation 12-13 Adjustment of ...er you the MAKITA blower, which refers in detail to ngers or hands
2 We are of state-ofthe-art technology with ergonomic design. The blower models BBX7600N combines the advantages...
Owners Manual - Page 4
...Fuel vapors accumulate at ground level
(risk of moisture, pitch, oil or grease. Change and clean protective clothing at regular intervals making sure that the fuel tank is to
start the engine ...Allow wet cloths to dry before disposing in
properly, covered container to refuel a hot or a running engine.
(9)
3 meters
4 Do not use any fuel contact with the instructions. Always ensure ...
Owners Manual - Page 5
... make sure that all relevant accident prevention instructions issued by the trade associations and by MAKITA. MAKITA will not accept any liability for accidents or damage caused by the use of any...by insurance companies. It will risk your safety. In particular check the correct adjustment of the carburetor.
• Clean the blower at high speed. • Pay attention to the direction of...
Owners Manual - Page 6
... oil E ngine oil volume C arburetor (Diaphragm-carburetor) Ignition s ys tem Spark plug E lectrode gap Noise Level 50Feet per ANSI B175-2-2000
BBX7600N
( kg)
10.2 22.4lbs
(mm) ( min-1 ) ( min-1 )
350 × 430 × 495
13.7 16.9 19.5... L x W x H) Max. Use the oil and spark plug speci ed by MAKITA. 2. TECHNICAL DATA
Model Mas s (without blower pipe) Dimension (without prior notice.
6
Owners Manual - Page 10
...marks on a level surface and remove the oil cap. the blower has not been running.
ᮦInspection: Set the blower down on the oil level gauge. Fill the ...better (4 stroke motor oil for the oil change the oil whenever it on a clean surface so that the oil level is cold i.e.
Verify that it does not accumulate ...
Recommended oil: MAKITA genuine oil or SAE10W-30 oil of operation.
Owners Manual - Page 18
...
Replace
Fuel filter
Clean/replace
٤
Clearance between air intake Adjust valve and air discharge valve
Oil tube
Inspect
Engine overhaul
Carburetor
Drain fuel
*1 Perform initial replacement after 20h operation. *2 For the 200 operating hour inspection, request Authorized Service Agent or a machine shop. *3 After emptying the fuel tank, continue to run the engine...
Owners Manual - Page 19
... for inspection and maintenance. Run engine at idling, and set to "OPEN"
Clogged fuel filter
Clean
Contaminated or clogged air cleaner
Clean
Abnormal carburetor
Make request for.... Pull strongly. Detached plug cap
Attach securely
Contaminated spark plug
Clean
Abnormal clearance of spark plug
Adjust clearance
Other abnormality of abnormality
Engine does not start still, remove...
Owners Manual - Page 20
... above limitation or exclusion may not apply to one of original purchase. IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE ...YEAR from state to you may also have been made or attempted by defective workmanship or material, Makita will repair (or at our option, replace) without charge. Some states do not allow the ...
Owners Manual - Page 22
EPA regulations. PARTS COVERED
Listed below may require scheduled maintenance and are the parts covered by Makita will, at the time of initial sale to all States, except the State of California
Makita U.S.A., Inc., (herein "Makita") warrant to the initial retail purchaser and each subsequent owner, that this utility equipment engine (herein "engine") was...
Owners Manual - Page 23
... they were made by the dealer or
service center authorized by Makita will perform the necessary repairs or adjustments within a reasonable amount of time and furnish you please refer to the nearest MAKITA Factory Service Center authorized by Makita when a problem exists. OBTAINING WARRANTY SERVICE To obtain warranty service, take your sales receipts indicating...
Owners Manual - Page 24
... be denied, however, solely because of the lack of our tools and accessories call: 1-800-4-MAKITA * Makita USA Inc. Head Office & Plant: 1950 Forbes Street, Whitby, ON L1N7B7.
24 MAINTENANCE, ... service department Tel 1-800-263-3734(Canada only), or visit our web site www.makita.ca *Makita Canada Inc. THINGS YOU SHOULD KNOW ABOUT THE EMISSION CONTROL SYSTEM WARRANTY MAINTENANCE AND REPAIRS...
Owners Manual - Page 25
... catalytic converters, fuel tanks, valves, filters, clamps, connectors, and other emission-related assemblies. Makita USA, Inc recommends that the engine or equipment is: (1) Designed, built, and equipped so .... As the small off-road engine owner, you should contact:
* For the nearest Makita service center, please visit www.makitatools.com * For technical support or questions regarding your ...
Owners Manual - Page 27
...Check clogging of maintenance; Clean and adjust if
necessary. 7) Check muffler exhaust outlet(or port).
If clogged, replace with new
ones.
Remove and clean if necessary.
5) Clean air cleaner. 6) Check... scheduled inspection and maintenance services performed at the times when recommended.
however, Makita USA, Inc may deny a warranty claim if your responsibility to perform required...
Owners Manual - Page 66
Makita Corporation
3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502, Japan
Owners Manual BBX7600N 12_10_29 WARNING: The Engine Exhaust from this product contains chemicals known to
the state of California to cause cancer, birth defects or other reproductive harm.
Parts Breakdown - Page 14
...BOLT M6X30
6
17
667-15002-00 BASE 1
1
18
667-15003-00 BASE 2
1
19
667-10080-02 VOLUTE CASE 2 ASS'Y, BBX7600
1
20
667-10050-10 SQUARE NUT
2
21
931202-6
NUT M5
2
21
017-00599-50 NUT M5
2
22
073-62899-80 CAUTION...version on top not indented.
PARTS BREAKDOWN PARTrSev B4_R05E/21A/2K01D3 OWN
BBX7600N EM4251
Products with multiple versions are attached. Tech Bulletins Fig.
Parts Breakdown - Page 15
...view. Part No. No.
Tech Bulletins Fig. SCREW M5X30
2
61
141771-1
ROCKER COVER, BBX7600
1
61
597-15007-01 ROCKER COVER COMPLETE
1
62
597-15009-00 ROCKER COVER GASKET
... CAM LIFTER
1
103
597-30020-02 CAM GEAR ASSY, BBX7600
1
Page 15 of 17
PB_05-2013_rev 4
PARTS BREAKDOWN PARTrSev B4_R05E/21A/2K01D3 OWN
BBX7600N EM4251
Products with multiple versions are attached.
Parts Breakdown - Page 16
...BBX7600N ...-0
PRIMER PUMP COVER
1
131
266582-4
TAPPING SCREW 3X24
4
132
266795-7
ADJUST SCREW
1
133
264065-8
CABLE ADJUST NUT M6
1
134
325922-6
SWIVEL
1
135
413140-9
WASHER
1
136
266704...153
667-65005-00 CHECK VALVE PLATE
1
154
412129-4
TUBE 3-105, BBX7600
1
155
282027-4
HOSE CLAMP 6, BBX7600
1
Page 16 of 17
PB_05-2013_rev 4 S.H.B. Description
Q'ty Unit
Notes...
Parts Breakdown - Page 17
...MUFFLER GASKET
1
SN19
169
597-30010-03 MUFFLER EXHAUST
1
Type 2
169
597-30010-02 EXHAUST MUFFLER, BBX7600
1
Type 1
SN19
170
020-00698-90 WASHER, BBX7600
3
w/ Type 1 muffler only
SN19
171
266771-1
SOCKET HEAD BOLT M6X18, BBX76 3
w/ Type 2 ... Tech Bulletins Fig.
PARTS BREAKDOWN PARTrSev B4_R05E/21A/2K01D3 OWN
BBX7600N EM4251
Products with multiple versions are attached.
Accessory Catalog - Page 10
...: 5/32 in -1 sharpen gauge to reduce the risk or severity of an
injury if contact is made from 25% post consumer
materials. size: models: All Makita chain saws.
models: 1/4"pitch and 3/8"Low Profile saw chain
OPE Accessory Catalog_13-03-27
10 Chain Saw Sharpening Kit 5/32" 744100-A
• Filing guide has...
Accessory Catalog - Page 12
OPE Accessory Catalog_13-03-27
12 Makita chain saw bar & chain reference
Reference page # for more detailed bar & chain specifications.
Similar Questions
Makita Eb5300th - Motor Chokes, Won't Rev
My Makita EB5300TH - Motor chokes, won't rev. Carb is clean, Fuel and fuel lines are fine.Engine sta...
My Makita EB5300TH - Motor chokes, won't rev. Carb is clean, Fuel and fuel lines are fine.Engine sta...
(Posted by tonyscardarella 1 year ago)
Blower Won't Rev To Full Throttle !
hello ". I bought this blower about a year ago ,Mir starts perfectly and worked really well , I left...
hello ". I bought this blower about a year ago ,Mir starts perfectly and worked really well , I left...
(Posted by mrsnappy 1 year ago)
What's The Difference Between These Makita Blowers?
What is the difference between the Makita BBX7600N, the BBX7600 and the BBX7600CA?
What is the difference between the Makita BBX7600N, the BBX7600 and the BBX7600CA?
(Posted by gavinjanet 11 years ago)
Makita Bbx7600 Leaf Blower Valve Clearance
what are the valve clearances on makita leaf blower bbx7600
what are the valve clearances on makita leaf blower bbx7600
(Posted by brian81601 11 years ago)