Mackie MR5mk2 Support Question
Mackie MR5mk2 Support Question
Find answers below for this question about Mackie MR5mk2.Need a Mackie MR5mk2 manual? We have 2 online manuals for this item!
Question posted by msmith194 on July 20th, 2015
No Sound Coming From Mr5 Mk2 Speakers
Both my MR5 MK2 speakers stopped emitting sound at the same time. Neither the Tweeter or the Bass emits any sound, not even a hiss. The fuse is good and it has 120 volts coming in. I checked the speakers and they read 4 ohms which is what they are rated at. None of the components on the PCB look burned up or broken in any way. Any idea on where the problem might be?
Current Answers
Related Mackie MR5mk2 Manual Pages
Owner's Manual - Page 1
MR5mk2
High Resolution Powered Studio Monitor
OWNER'S MANUAL
Owner's Manual - Page 2
...modifications to sufficiently intense noise for replacement of time. Individuals vary considerably in susceptibility to noise-induced...Duration, per day in hours 8 6 4 3 2 1.5 1
Sound Level dBA, Slow Response 90 92 95 97 100 102 105
...) dans le livret d'instruction accompagnant l'appareil. MR5mk2
Important Safety Instructions
1. Read these instructions. 3. Follow all warnings. 4. ...
Owner's Manual - Page 3
...MR5MK2 LIMITED WARRANTY 15
• Precisely tuned to work interchangeably with other Mackie products. All Rights Reserved. Owner's Manual
3 INPUT LEVEL 6 3. MAINS INPUT AND FUSE 7
• Neodymium magnet minimizes distortion and
7. BASS...against power compression
8. At the same time, your national law.
LOW FREQ ...tweeter
6. Correct disposal of natural resources.
Owner's Manual - Page 4
...of these !
The MR5mk2s feature a 5.25-inch high-precision, low-distortion woofer and a 1-inch neodymium silk dome tweeter.
MR5mk2
Introduction
The MR5mk2 Mackie Reference Monitor is...time domain characteristics of high-frequency sounds.
All-New Transducers... Precision Power Amplifiers... Investments in its category. With unbelievable power, performance and clarity, the MR5mk2...
Owner's Manual - Page 5
...coming out the speakers. This will illuminate.
8.
Luckily we've armed you with the voltage corresponding to the markings next to the IEC socket. Leave the High Freq [3] and Low Freq [4] Filter switches at their bass...). Nevertheless, please take the time to read the rest of the MR5mk2.
including room shape, room ... the walls and corners and you 're good and ready.
1. This is not a ...
Owner's Manual - Page 6
...speakers. TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY
NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. INPUT LEVEL
The MR5mk2 expects a line-level signal at a time to the input jacks.
• The MR5mk2...CAUTION: REPLACE WITH THE SAME FUSE AND RATING. SIGNAL INPUTS
There ... sound ...
Owner's Manual - Page 7
... replacing the fuse.
7. BASS REFLEX PORT
A bass reflex system uses the radiation from the speaker and the...bass content on page 9 for it at the mains input [6].
8
Owner's Manual
7 The fuse is necessary, use the +4 dB setting.
Your ears will thank you play it .
5. When the power switch is turned on and the MR5mk2 is available at least that the resulting mix only sounds good...
Owner's Manual - Page 8
...Integrated Magnetic Shielding
Input Signal Wiring
You should be necessary to move the speakers a few inches away.
8
MR5mk2
Speaker levels are much higher than line levels and can build your own.... you choose to ignore the warning signs (i.e., excessive distortion), you can still damage the speakers in the MR5mk2 by causing it may be able to assist, or you follow these guidelines.
•...
Owner's Manual - Page 9
...before the speaker.
Remove the fuse and replace it 's not the monitor.
• Too much bass or not enough bass? Use an...hiss is an indication of our website (www.mackie.com/support) where you are secure. If it sounds bad there, it with a small screwdriver. Replace the fuse... an unbalanced output to the MR5mk2 balanced input, make sure the AC outlet is live (check with a room mode where...
Owner's Manual - Page 10
... living outside the United States can be obtained through local dealers or distributors. To locate your new MR5mk2?
• Visit www.mackie.com and click Support to find: FAQs, manuals, and addendums....
• Email us at 1-800-898-3211 (normal business hours, Pacific Time), to explain the problem.
Service for Mackie products is located in your area. They will tell...
Owner's Manual - Page 11
...
Owner's Manual
11 TRS jacks and plugs are used to make balanced connections to the MR5mk2. They are wired as phono plugs) and jacks are often used in home stereo and.... Owner's Manual
Appendix B: Connectors
XLR Connectors
XLR connectors are used to make balanced connections to the MR5mk2.
1/4" TRS Balanced Wiring: Hot (+) Tip Cold (-) Ring Shield (Ground) Sleeve
RING SLEEVE SLEEVE ...
Owner's Manual - Page 12
...120 VAC, 60 Hz 240 VAC, 50 Hz 220 VAC, 60 Hz 100 VAC, 50/60 Hz
Note: The MR5mk2 does not support multiple voltage configurations. MR5mk2
Appendix C: Technical Information
MR5mk2 Specifications
Acoustic Performance
Free Field Frequency Response:
50 Hz - 20 kHz
Sound...Fuse...dome tweeter
...time without notice.
7.8" / 197 mm
11.3" / 287 mm
10.6" / 269 mm
MR5mk2 WEIGHT 14.3 lb /
6.5 kg
12...
Owner's Manual - Page 13
...;2011 LOUD Technologies Inc.
Owner's Manual
13 POWER LED
+ LO VDC
- Owner's Manual
MR5mk2 Block Diagram
RCA UNBALANCED
LINE INPUT
XLR BALANCED
12
LINE INPUT 3
1/4" UNBALANCED
LINE INPUT
INPUT ...VDC HI-FREQUENCY POWER AMPLIFIER
HI-FREQ
LO-FREQ
-HI VDC
HI-FREQUENCY DRIVER
TWEETER
OVEREXCURSION PROTECT
34 Hz
FUSE
POWER
LOW FREQ +4 dB +2 dB 0
DARK SIDE OF THE MOON
TOROIDAL ...
Owner's Manual - Page 14
...MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. DISCONNECT SUPPLY CORD BEFORE CHANGING FUSE. NE PAS OUVRIR
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS...+2dB +4dB (NORMAL)
INPUT
OFF MAX LEVEL
ON
CAUTION: REPLACE WITH THE SAME FUSE AND RATING. MR5mk2
14
MR5mk2
AVIS: RISQUE DE CHOC ELECTRIQUE - DO NOT REMOVE COVER.
Owner's Manual - Page 15
...'s Manual
15 or Canada, please visit www.mackie.com/warranty to products purchased in materials and workmanship under normal use during normal business hours Pacific Time, excluding weekends or LOUD holidays. Please retain the original dated sales receipt as the specific duration of the Warranty for your local distributor, and information...
Owner's Manual (Español) - Page 14
...)
SETTINGS
HIGH FREQ FILTER
-2dB 0 +2dB (NORMAL)
LOW FREQ FILTER
0 +2dB +4dB (NORMAL)
INPUT
OFF MAX LEVEL
ON
CAUTION: REPLACE WITH THE SAME FUSE AND RATING. MR5mk2
14
MR5mk2
AVIS: RISQUE DE CHOC ELECTRIQUE - REFER SERVICING TO QUALIFIED PERSONNEL. DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE.
DISCONNECT SUPPLY CORD BEFORE CHANGING...
Similar Questions
My Speaker Lid Doesn't Come On It Just Makes A Zaping Noise When I Turn Power On
(Posted by Tyreejohnson939 11 months ago)
Nothing Comes Out Of The Speaker.
Lights come on and I can hear the hum of the speakers. I have my guitar plugged into channel 1 no so...
Lights come on and I can hear the hum of the speakers. I have my guitar plugged into channel 1 no so...
(Posted by Joeantonucci 2 years ago)
Why Won't My Fairly New Srm 650 Powered Speaker Turn On?
I went to a gig plugged it in and it no longer turns on
I went to a gig plugged it in and it no longer turns on
(Posted by Jarrodamanzi 2 years ago)
Mackie Hd1521 Speaker Doesn’t Turn On.
I have a pair of mackie hd1521. One works excellent. The other stopped producing sound. Took it to a...
I have a pair of mackie hd1521. One works excellent. The other stopped producing sound. Took it to a...
(Posted by Raulromo34 3 years ago)
Need Speaker Stand Cup
I need to replace the plastic cup in the bottom of the TH12A speaker that the speaker stand pole ext...
I need to replace the plastic cup in the bottom of the TH12A speaker that the speaker stand pole ext...
(Posted by tditmer40351 3 years ago)